|
Raritan PHII PUMP Phii Pump Assy Complete
|
468.75 |
|
|
Check all of your impellers contained within the engine cooling pumps, bilge pumps, ballast pumps, and so on. One of the biggest contributors to impeller deterioration and damage is sitting idle in the same position for several months, so a proper check of the impeller(s) is vital to a reliable operation of the boat after storage and/or no operation.
Replacing an impeller is a fairly easy and straightforward process and one that you have probably done in the past. It is important to use the right tool to remove an impeller from the pump. Channel lock or needle-nose pliers are fine, but using an impeller removal tool is the best choice. Never use a screwdriver to pry an impeller out of a pump; you could accidentally score the bronze housing which can lead to leaks. Make sure you know how the impeller is being held in place. Some are sealed to the shaft with an O-ring; others are held in place with a set screw and others with a c-clip.
Make sure to check the pump and the water lines for any trash or chunks of rubber that may have broken off from the impeller. Even the smallest blockage can cause major engine cooling and overheating issues. Also, remember to properly lubricate your new impeller with Vaseline or the lubricant included with the new impeller. This will reduce friction for a brand new impeller on a dry startup.
Most importantly, make sure you are using the right impeller for the application. We have seen many instances of people who have replaced an impeller with something that is close to the original, but not exactly right, and this can cause major problems for the engine once normal operation resumes. You cannot match the size of the used impeller to a new one to determine the replacement, as a used impeller can be swollen and disfigured from its original specifications. The best method is to obtain the impeller number off of the impeller itself, usually located on the edge of the shaft hole of the impeller, or obtain the part number of the pump, usually stamped into the bronze housing.
You can find just about every impeller that needs to be replaced at CLR Marine. We carry Sherwood, Jabsco and Globe just to mention a few. We also carry many of the miner and major rebuild kits for many pumps. A minor repair kit consists of the impeller and any gaskets or O-rings that may be needed to replace the impeller. Our major rebuild kits include everything to rebuild that pump except for the shaft. All kits are put together at time of order so you will always see the Quantity on Hand as 0.
|
|
|
March 809-PL-HS Magnetic Drive Beer Pump
The March 809-PL-HS Home Brew Beer Pump is great for all your brewing needs.
The March 809 PL HS hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include brewing, home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Home Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
Unit System - 60Hz
Max Flow - 6 GPM - 18.9 LPM
Max Head - 12.1 FT - 2.5 M
Power - .04 HP - .029 KW
Electrical - 115V 60HZ
Type - Centrifugal Mag Drive
Inlet - 1/2"MPT
Outlet - 1/2"MPT
Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Can handle liquids of 250F Materials and is FDA Food Compliant with 6 Foot Cord and plug Components are UL Recognized.
Made in American
|
348.08 |
|
|
Ampco Pumps GS8101150 CB114 Seal Kit
Material: Viton
Product: Replacement Kit
Series: CB+ Craft Brew Pump Series
Model: CB+ 114/214
|
263.25 |
|
|
March 815 PL C Beer Pump
March Pump’s industrial 815-PL-C is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 8 gallons per minute at 3 feet, and its maximum head is 18.6 Feet (8PSI).
At 60Hz
SystemUS Metric
Max Flow8 GPM 30.3 LPM
Max Head18.6 FT 5.7 M
Power0.04 HP 0.029 KW
At 50Hz
USMetric
7.9 GPM30 LPM
13.5 FT4.1 M
0.04 HP0.029 KW
Electrical: 115V 50/60Hz or 230V 50/60Hz
Inlet: 3/8"FPT & 3/4"MPT
Outlet: 1/2"MPT
Wet End: Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Max Internal Pressure: 50 PSI / 3.4 bar
Max Liquid Temperature: 250 °F / 121 °C
Applications for the 815-PL-C Magnetic Drive Pump include home brewing, hot water systems, solar heating, and fryers.
The 815-PL-C has pumped Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water.
|
332.48 |
|
|
March 815 PL Beer Pump 115V
March Pump’s 815-PL Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7 gallons per minute at 4.5 feet, and its maximum head is 18.6 Feet (8PSI).
Wet End: Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Materials are FDA Food Compliant: Components are UL Recognized
Max Internal Pressure: 50 PSI / 3.4 bar
Max Liquid Temperature: 250 °F / 121 °C
Note: Product image may be different than actual product received.
The 815-PL Beer Pump has pumped Hot Water and Hot Wort.
March Pump’s 815-PL Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7 gallons per minute at 4.5 feet, and its maximum head is 18.6 Feet (8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 1/2 inch male pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The 815-PL Beer Pump motor has a six foot cord, a plug, and a base. The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
|
344.18 |
|
|
March 815 Series Mag-Drive Centrifugal Pumps
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze 230V High Speed 7.2GPM 1/2"MPT Ports
|
428.03 |
|
|
March 809 815 Series Mag-Drive Centrifugal Pumps
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze with Base 24VDC High Speed 7.5GPM 1/2"MPT Ports
|
498.00 |
|
|
March 809 815 Series Mag-Drive Centrifugal Pumps Bronze Center Inlet 115V 4.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
426.08 |
|
|
March Mag-Drive Centrifugal Pumps Bronze Center Inlet 12VDC 5.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
479.06 |
|
|
March Mag-Drive Centrifugal Pumps Bronze 115V High Speed 4.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
443.63 |
|
|
March 809 BRC HS 12VDC Mag-Drive Pump
March Mag-Drive Centrifugal Pumps Bronze 12VDC High Speed 5.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC High Speed 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
499.69 |
|
|
March Mag-Drive Centrifugal Pumps Bronze 230V High Speed 4.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 230V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
417.30 |
|
|
March 809 BRC HS 24VDC Mag-Drive Centrifugal Pumps Bronze 24VDC High Speed 5.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 24VDC High Speed 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
501.56 |
|
|
March 809 BR HS Mag-Drive Centrifugal Pump Bronze 24V Pump
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze 24VDC High Speed 7.5GPM 1/2"MPT Ports
|
463.13 |
|