|
Chesapeake White SS 4" Speedometer w/LCD Heading Display- 60MPH (GPS)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
The GPS Speedometer is a drop in replacement for your current speedometer to match your existing instrument dash.
GPS information is gathered from an internal GPS antenna. No external antenna required. The Faria GPS Speedometer uses a highly accurate 48 channel GPS receiver. You can be sure that the Faria GPS Speedometer is giving you the most accurate GPS information available on the market today.
Course Over Ground (COG) and actual heading (compass heading over ground) are displayed on the digital LCD.
Speed data is shown by an analog pointer. This pointer is driven by a digital stepper motor for increased accuracy and minimized pointer bounce during vessel operation.
Benefits:
No external GPS antenna required
Ultra fast Satellite acquisition time (TTFF) 1 second from Hot start
Speed Accuracy of +/- 1 MPH
Heading Accuracy of +/- 1 Degree
Ideal replacement for speed sensing devices (pitot tube and paddle wheel) that fail over time
Perfect for slow moving vessels where pitot tubes just don't work
Deutsch connectors
4"- Hole Size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Dual Scale - Imperial and Metric
Factory P/N SGP003
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
275.99 |
|
|
Chesapeake White SS 4" Speedometer - 60MPH (Pitot)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic speedometers operate by capturing pulses produced by a sensor. the pulses are then electronically converted to a speed reading very much like a tachometer converts ignition pulses to RPM.
Pitot tube type speedometers operate by pressure from the water being forced into the pitot tube. This pressure is then transmitted through flexible tubing to the bourdon tube movement inside the speedometer head where it is converted into a speed reading by the movement mechanism.
∗ Pitot tube sold separately.
4" - Hole Size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
12 VDC negative ground
Can be adapted for 24 VDC systems
Dual Scale - Imperial and Metric
Factory P/N SE9521
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
66.10 |
|
|
Chesapeake White SS 4" Speedometer - 80MPH (Pitot)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic speedometers operate by capturing pulses produced by a sensor. the pulses are then electronically converted to a speed reading very much like a tachometer converts ignition pulses to RPM.
Pitot tube type speedometers operate by pressure from the water being forced into the pitot tube. This pressure is then transmitted through flexible tubing to the bourdon tube movement inside the speedometer head where it is converted into a speed reading by the movement mechanism.
∗ Pitot tube sold separately.
4" - Hole Size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
12 VDC negative ground
Can be adapted for 24 VDC systems
Dual Scale - Imperial and Metric
Factory P/N SE9522
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
65.75 |
|
|
Chesapeake White SS 4" Tachometer with Hourmeter - 7000 RPM (Gas) (Outboard)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
4" - Hole size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
12 VDC negative ground
Can be adapted for 24 VDC systems
Technical Specifications:
7 character LCD display
0-999999.9 Hours
Updates in .1 increments
Factory P/N TCH008
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
145.13 |
|
|
Chesapeake White SS 4" Tachometer with Hourmeter - 6000 RPM (Gas) (Inboard)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
4" - Hole size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Technical Specifications:
7 character LCD display
0-999999.9 Hours
Updates in .1 increments
Factory P/N TC9128
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
145.13 |
|
|
Chesapeake White SS 4" Tachometer w/Systemcheck Indicator - 7000 RPM (Gas - Johnson/Evinrude Outboard)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
SystemCheck Warnings:
No Oil
Engine Overheat
Check Engine
Low Oil
4" - Hole size: 3.375" (85mm)
For Engine Types:
Johnson/Evinrude Outboard
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC9881
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
202.38 |
|
|
Chesapeake White SS 4" Tachometer with Hourmeter (4000 RPM) (Diesel) Mech. Takeoff & Var. Ratio Alt
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12vDC, Ground and one of the signal sources listed above.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
4" - Hole size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
12 VDC negative ground
Can be adapted for 24 VDC systems
Scale - 0 to 10000 Hours
Factory P/N TD9108
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
155.98 |
|
|
Chesapeake White SS 4" Tachometer with Suzuki Monitor - 7000 RPM (Gas) (Suzuki Outboard)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
SystemCheck Warnings:
Rev. Limit
Engine Overheat
Check Engine
Low Oil
4" - Hole size: 3.375" (85mm)
For Engine Types:
(Suzuki Outboard)
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC4025
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
243.37 |
|
|
Chesapeake White SS 4" Studded Speedometer - 60MPH (GPS)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
The GPS Speedometer is a drop in replacement for your current speedometer to match your existing instrument dash.
GPS information is gathered from an internal GPS antenna. No external antenna required. The Faria GPS Speedometer uses a highly accurate 48 channel GPS receiver. You can be sure that the Faria GPS Speedometer is giving you the most accurate GPS information available on the market today.
Course Over Ground (COG) and actual heading (compass heading over ground) are displayed on the optional digital LCD.
Speed data is shown by an analog pointer. This pointer is driven by a digital stepper motor for increased accuracy and minimized pointer bounce during vessel operation.
Benefits:
No external GPS antenna required
Premium LED back-lit dials
Ultra fast Satellite acquisition time (TTFF) 1 second from Hot start
Speed Accuracy of +/- 1 MPH
Heading Accuracy of +/- 1 Degree
Digital stepper motor driven pointers
Ideal replacement for speed sensing devices (pitot tube and paddle wheel) that fail over time
Perfect for slow moving vessels where pitot tubes just don't work
Deutsch connectors
4"- Hole Size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Dual Scale - Imperial and Metric
Factory P/N SGP113
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
130.55 |
|
|
Chesapeake White SS 5" Speedometer - 60 MPH (GPS)(Studded)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
The GPS Speedometer is a drop in replacement for your current speedometer to match your existing instrument dash.
GPS information is gathered from an internal GPS antenna. No external antenna required. The Faria GPS Speedometer uses a highly accurate 48 channel GPS receiver. You can be sure that the Faria GPS Speedometer is giving you the most accurate GPS information available on the market today.
Course Over Ground (COG) and actual heading (compass heading over ground) are displayed on the optional digital LCD.
Speed data is shown by an analog pointer. This pointer is driven by a digital stepper motor for increased accuracy and minimized pointer bounce during vessel operation.
Benefits:
No external GPS antenna required
Premium LED back-lit dials
Ultra fast Satellite acquisition time (TTFF) 1 second from Hot start
Speed Accuracy of +/- 1 MPH
Heading Accuracy of +/- 1 Degree
Digital stepper motor driven pointers
Ideal replacement for speed sensing devices (pitot tube and paddle wheel) that fail over time
Perfect for slow moving vessels where pitot tubes just don't work
Deutsch connectors
5"- Hole Size: 4.375" (112mm)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Dual Scale - Imperial and Metric
Factory P/N SGP502
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
283.66 |
|
|
Chesapeake White SS 4" Multifunction Gauge
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
4" - Hole size: 3.375" (85mm)
Multi-Function Gauge Displays:
Fuel (E-1/2-F)
Voltmeter (10 - 18 VDC)
Oil Pressure (0 - 80 PSI)
Water Temperature (120 - 220° F)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N GF0008
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
113.69 |
|
|
Chesapeake White SS 5" Tachometer w/Digital Hourmeter - 6000 RPM (Gas) (Inboard)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12vDC, Ground and one of the signal sources listed above.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
5" - Hole size: 4.375" (112mm)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Scale - 0 to 10000 Hours
Factory P/N TC9381
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
209.93 |
|
|
Chesapeake Black SS 4" Tachometer w/Systemcheck Indicator - 7000 RPM (Gas) (Johnson / Evinrude Outboard)
Perimeter-lighted Black dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
SystemCheck Warnings
No Oil
Engine Overheat
Check Engine
Low Oil
4" - Hole size: 3.375" (85mm)
For Engine Types:
(Johnson / Evinrude Outboard)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC9884
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
202.38 |
|
|
Chesapeake White SS 4" Tachometer - 6000 RPM (Gas) (Inboard & I/O)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
4" - Hole size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC9796
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
97.54 |
|
|
Chesapeake White SS 4" Tachometer - 7000 RPM (Gas) (All Outboards)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Electronic tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
4" - Hole size: 3.375" (85mm)
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC9002
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
97.54 |
|