|
200A, 40V 3-Bank Ideal Battery Isolator
Features:
Waterproof Expoxy Sealed Construction
Easy Connection
Most Efficient use of Available Alternator Output
Maximize Battery Performance
Three year parts and labour warranty
Analytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electrical
isolation between the battery banks or between a vehicle and trailer.
Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time.
While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load.
|
333.58 |
|
|
AC Charger 2-Bank 20A 12V Out, 110VAC In, with Digital Volt/Amp Meter
The traditional BCA310 series chargers feature 300 watts of precision charging power for 1, 2 or 3 banks of batteries at 12, 24, 32, 36, 48 or 72(rail) volts DC. Models are available to operate from 110 or 220 volts AC at 50, 60 or 400 Hz.
All models feature user selectable 2-stage or 3-stage charging profiles, temperature compensation and user initiated equalization for optimum charging and maximum battery life.
Features:
300 watts of charging power
One, two or three bank charging
Temperature compensation
Manual equalization mode
Two or three stage charging profiles
Low EMI
110 and 220 VAC inputs
Adjustable float voltage
Three year parts and labor warranty
|
539.99 |
|
|
2-Bank Battery Isolator, 200A, 40V
Analytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electrical
isolation between the battery banks or between a vehicle and trailer.
Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time.
While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load.
Features:
Waterproof Expoxy Sealed Construction
Easy Connection
Alternator/Charger post 5/16", Battery Post 1/4"
Most Efficient use of Available Alternator Output
Maximize Battery Performance
Three year parts and labour warranty
|
273.55 |
|
|
Single Bank Battery Isolator, 200A, 40V
Analytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electrical
isolation between the battery banks or between a vehicle and trailer.
Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time.
While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load.
Features:
Waterproof Expoxy Sealed Construction
Easy Connection
Alternator/Charger Post 5/16", Battery Post 1/4"
Most Efficient use of Available Alternator Output
Maximize Battery Performance
Three year parts and labour warranty
|
219.74 |
|
|
Battery Mate 1603 IG Isolator - 120 Amp, 3 Bank
The Battery Mate is the ultimate solution for charging several batteries simultaneously and is compatible with any type of alternator/battery charger, in both existing and new systems. As the voltage loss between the alternator and battery is negligible, the Battery Mate performs far better than conventional battery isolators. This ensures fast and complete charging of your batteries without having to make additional adjustments to the alternator.
While battery isolators are conventional diode splitters, the Battery Mate's technology is electronic and includes mosfets (transistors). Its components compensate for variations in voltage and ensure that charging continues at the right voltage level, even with several battery banks. The input side on the Battery Mate is connected to the alternator and/or battery charger, while two batteries are connected to the output side. The Battery Mate is easy to install on a DIN rail (industry standard).The Mastervolt Battery Mate can be used in any application even if the standard alternator need external excitation or voltage sensing. In this case the additional IG contact can be connected.
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
378.04 |
|
|
Battery Mate 2503 IG Isolator - 200 Amp, 3 Bank
The Battery Mate is the ultimate solution for charging several batteries simultaneously and is compatible with any type of alternator/battery charger, in both existing and new systems. As the voltage loss between the alternator and battery is negligible, the Battery Mate performs far better than conventional battery isolators. This ensures fast and complete charging of your batteries without having to make additional adjustments to the alternator.
While battery isolators are conventional diode splitters, the Battery Mate's technology is electronic and includes mosfets (transistors). Its components compensate for variations in voltage and ensure that charging continues at the right voltage level, even with several battery banks. The input side on the Battery Mate is connected to the alternator and/or battery charger, while two batteries are connected to the output side. The Battery Mate is easy to install on a DIN rail (industry standard).The Mastervolt Battery Mate can be used in any application even if the standard alternator need external excitation or voltage sensing. In this case the additional IG contact can be connected.
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
408.01 |
|
|
AC Charger 2-Bank 40A, 12V Out, 110VAC In with Digital Volt/Amp Meter
The traditional BCA610 series chargers feature 600 watts of precision charging power for 1 or 2 banks of batteries at 12, 24, 32, 36, 48 or 72(rail) volts DC. Models are available to operate from 110 or 220 volts AC at 50, 60 or 400 Hz.
All models feature user selectable 2-stage or 3-stage charging profiles, temperature compensation and user initiated equalization for optimum charging and maximum battery life.
Features:
Two or three stage charging profiles
Adjustable float voltage
One or two bank charging (three bank optional)
Temperature compensation
Low EMI
Manual equalization mode
Three year warranty (parts & labor)
|
800.84 |
|
|
AC Charger 2-Bank 30A 32V Out/110V In with Digital Volt/Amp Meter
The traditional BCA1000 series chargers feature 1000 watts of precision charging power for 1 or 2 banks of batteries at 12, 24, 32, 36, 48 or 72(rail) volts DC. Models are available to operate from 110 or 220 volts AC at 50, 60 or 400 Hz.
All models feature user selectable 2-stage or 3-stage charging profiles, temperature compensation and user initiated equalization for optimum charging and maximum battery life.
Features:
Two or three stage charging profiles
Adjustable float voltage
One or two bank charging (three bank optional)
Temperature compensation
Low EMI
Manual equalization mode
Three year warranty (parts & labor)
|
1498.63 |
|
|
15A Battery Charger - 12V - 3-Bank - 3-Stage w/Dip Switch & Lugs
This advanced fully automatic three-stage 15 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload and short-circuit protection. The unit allows charging of up-to 3 separate battery banks.
Features:
High efficiency
Commercial Grade
Lightweight
Quiet operation
Industry Proven Design – 1000s of units in operation
2 or 3 stage charging (user selectable)
120 or 230 VAC, 50/60 Hz (user selectable)
Voltage meter display – Ammeter and LED power status
For all types of Lead Acid batteries
Charge with a battery load or stand alone
Use as a power supply or DC UPS
UPC: Universal Protection Circuit – short circuit, overload, reverse battery polarity
Charge 3 banks of batteries at once – no isolator necessary
Specifications:
Input: 120 VAC 60 Hz or 230 VAC 50 Hz
Output: 12 VDC
Amps: 15 Amps
Weight: 4.4 (lbs)
Weight: 1.96 (kg)
Dimensions: 8.5 x 8.5 x 3 (in)
Dimensions: 21.6 x 21.6 x 7.6 (cm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
174.96 |
|
|
30A Battery Charger - 12V - 3-Bank - 3-Stage w/Dip Switch & Lugs
This advanced fully automatic three-stage 30 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 3 separate battery banks.
Features:
High efficiency
Commercial Grade
Lightweight
Quiet operation
Industry Proven Design – 1000s of units in operation
2 or 3 stage charging (user selectable)
120 or 230 VAC, 50/60 Hz (user selectable)
Voltage meter display – Ammeter and LED power status
For all types of Lead Acid batteries
Charge with a battery load or stand alone
Use as a power supply or DC UPS
UPC: Universal Protection Circuit – short circuit, overload, reverse battery polarity
Charge 3 banks of batteries at once – no isolator necessary
Specifications:
Input: 120 VAC 60 Hz or 230 VAC 50 Hz
Output: 12 VDC
Amps: 30 Amps
Weight: 7 (lbs)
Weight: 3.17 (kg)
Dimensions: 10.5 x 8.5 x 3 (in)
Dimensions: 26.7 x 21.6 x 7.6 (cm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
245.04 |
|
|
15A Battery Charger - 24V - 3-Bank - 3-Stage w/Dip Switch & Lugs
This advanced fully automatic three-stage 15 Amp battery charger is ideal for charging all types of 24 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 3 separate battery banks.
Features:
High efficiency
Commercial Grade
Lightweight
Quiet operation
Industry Proven Design – 1000s of units in operation
2 or 3 stage charging (user selectable)
120 or 230 VAC, 50/60 Hz (user selectable)
Voltage meter display – Ammeter and LED power status
For all types of Lead Acid batteries
Charge with a battery load or stand alone
Use as a power supply or DC UPS
UPC: Universal Protection Circuit – short circuit, overload, reverse battery polarity
Charge 3 banks of batteries at once – no isolator necessary
Specifications:
Input: 120 VAC or 230 VAC
Output: 24 VDC
Amps: 15 Amps
Remote Control: 900-RC
Weight: 6 (lbs)
Weight: 2.72 (kg)
Dimensions: 10.5 x 8.5 x 3 (in)
Dimensions: 26.7 x 21.6 x 7.6 (cm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
245.04 |
|
|
Battery Isolator
Max Current: 70 Amp
Configuration: 1 alt., 3 batt.
ProMariner Battery Isolator, with gold-plated terminals and improved efficiency, provide enhanced charging
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
95.99 |
|
|
AC Charger 1-Bank, 100A, 12V Out, 110/220 In, IP66 Rated, Ruggedized & Wide Temp
The BCA1550 Series battery charger provides up to 1000 watts of charging power to a one or two-bank battery system at 12, 24, 32, 36, 48, or 72 (Rail) VDC from an 85 – 264 VAC source.
The BCA1550 Series chargers (BCA) and power supplies (PWS) are designed to supply a DC load or charge a battery at 12, 24, 32, 36, 48, or 72 (Rail) VDC. The 1550 family provides up to 1500 watts of precision power (the 1050 family supplies up to 1000 watts). The 1550 and 1050 families are identical to their previous models (1505 and 1005, respectively) in form, fit, and function as a direct drop-in replacement.
Internally, the recently updated design incorporates a Power Factor Corrected (PFC) input stage allowing the charger to run continuously from 85 – 264 VAC at 50 or 60Hz with a Power Factor of 0.99 or better from 10% to 100% load. Heavy input filtering reduces EMI to extremely low levels to prevent interference with nearby sensitive electronics. These units are constructed from heavy-duty extruded aluminum chassis and aluminum ventilated front and rear panels with thermostatically controlled cooling fans and all stainless steel fasteners for rugged duty. Reliability features include LED status indicators, input circuit breaker, thermal shutdown, current limiting, reverse polarity connection protection, and output short circuit shutdown with automatic recovery.
Features:
Power Factor Corrected AC Input
Fast and accurate charging
Can function as a power supply
Visual indicators for operation and errors
Five-year parts and labor warranty
Specifications:
Input Voltage (AC): 85-265 VAC
Input Current (Max Amps): 100 A
Output Voltage (DC): 12 VDC
Nominal Output VDC: 12 VDC
Charging Current: 100 A
Number of Battery Banks: 1
IP Rating: IP66
Mounting: Panel
Approvals: CSA, UL
Net Weight: 12 lbs
Gross Weight: 12 lbs
|
2509.32 |
|
|
AC Charger 2-Bank, 60A, 24V Out, 110/220 In, IP66 Rated, Ruggedized & Wide Temp
The BCA1550 Series battery charger provides up to 1000 watts of charging power to a one or two-bank battery system at 12, 24, 32, 36, 48, or 72 (Rail) VDC from an 85 – 264 VAC source.
The BCA1550 Series chargers (BCA) and power supplies (PWS) are designed to supply a DC load or charge a battery at 12, 24, 32, 36, 48, or 72 (Rail) VDC. The 1550 family provides up to 1500 watts of precision power (the 1050 family supplies up to 1000 watts). The 1550 and 1050 families are identical to their previous models (1505 and 1005, respectively) in form, fit, and function as a direct drop-in replacement.
Internally, the recently updated design incorporates a Power Factor Corrected (PFC) input stage allowing the charger to run continuously from 85 – 264 VAC at 50 or 60Hz with a Power Factor of 0.99 or better from 10% to 100% load. Heavy input filtering reduces EMI to extremely low levels to prevent interference with nearby sensitive electronics. These units are constructed from heavy-duty extruded aluminum chassis and aluminum ventilated front and rear panels with thermostatically controlled cooling fans and all stainless steel fasteners for rugged duty. Reliability features include LED status indicators, input circuit breaker, thermal shutdown, current limiting, reverse polarity connection protection, and output short circuit shutdown with automatic recovery.
Features:
Power Factor Corrected AC Input
Fast and accurate charging
Can function as a power supply
Visual indicators for operation and errors
Five-year parts and labor warranty
Specifications:
Input Voltage (AC): 85-265 VAC
Input Current (Max Amps): 60 A
Output Voltage (DC): 24 VDC
Nominal Output VDC: 24 VDC
Charging Current: 60 A
Number of Battery Banks: 2
IP Rating: IP66
Mounting: Panel
Approvals: CSA, UL
Net Weight: 12 lbs
Gross Weight: 12 lbs
|
2509.32 |
|
|
AC Charger 2-Bank, 60A, 24V Out, 110/220 In, IP66 Rated, Ruggedized & Wide Temp
The BCA1550 Series battery charger provides up to 1000 watts of charging power to a one or two-bank battery system at 12, 24, 32, 36, 48, or 72 (Rail) VDC from an 85 – 264 VAC source.
The BCA1550 Series chargers (BCA) and power supplies (PWS) are designed to supply a DC load or charge a battery at 12, 24, 32, 36, 48, or 72 (Rail) VDC. The 1550 family provides up to 1500 watts of precision power (the 1050 family supplies up to 1000 watts). The 1550 and 1050 families are identical to their previous models (1505 and 1005, respectively) in form, fit, and function as a direct drop-in replacement.
Internally, the recently updated design incorporates a Power Factor Corrected (PFC) input stage allowing the charger to run continuously from 85 – 264 VAC at 50 or 60Hz with a Power Factor of 0.99 or better from 10% to 100% load. Heavy input filtering reduces EMI to extremely low levels to prevent interference with nearby sensitive electronics. These units are constructed from heavy-duty extruded aluminum chassis and aluminum ventilated front and rear panels with thermostatically controlled cooling fans and all stainless steel fasteners for rugged duty. Reliability features include LED status indicators, input circuit breaker, thermal shutdown, current limiting, reverse polarity connection protection, and output short circuit shutdown with automatic recovery.
Features:
Power Factor Corrected AC Input
Fast and accurate charging
Can function as a power supply
Visual indicators for operation and errors
Five-year parts and labor warranty
Specifications:
Input Voltage (AC): 85-265 VAC
Input Current (Max Amps): 41 A
Output Voltage (DC): 32 VDC
Nominal Output VDC: 32 VDC
Charging Current: 41 A
Number of Battery Banks: 2
IP Rating: IP66
Mounting: Panel
Approvals: CSA, UL
Net Weight: 12 lbs
Gross Weight: 12 lbs
|
2566.85 |
|