Oberdorfer N991R-32-A89 Gear Pump 3/8 Rv 24V  

Oberdorfer N1100 Series Gear Pump FEATURES Pump Body: Bronze Ports: 1 1/4" NPT Flow: 40 GPM Max Pressure: 150 PSI Max Bearings: Self-Lubricating Carbon Bearings Gears: Bronze Helical Gears Shaft Seal: Viton Lip Seals Standard, Buna Lip Seal Optional. Shaft: Stainless Steel Shafts Motor / Drive: The pump is driven directly from the electric motor shaft by means of a flexible coupling. An aluminum adapter connects the pump to the motor. We have many motor options and can assemble for you.    CHARACTERISTICS BRONZE CLOSE COUPLED ROTARY GEAR PUMPS   Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.   Oberdorfer Gear Pump Bronze 1 1/4"NPT Viton Lip Seal With Bracket 182TC/184TC  

OBERDORFER CB9000L CAST IRON GEAR PUMP 1" FEATURES: • Flows to 24.8 GPM • Max. RPM: 1725 • Max. PSI: 100 • Suction lift to 19.5 ft.* • Maximum viscosity to 100,000 SSU at reduced speed (max. input torque of 160 in.-lbs.) • Housing gasket: Vellomoid • Construction: Cast Iron housing, Steel gears, Steel shafts • Shaft Seals: Synthetic Braided compression packing with Teflon dispersion • Shaft Bearing Journals: Grease lubricated Cast Iron • Temperature range: -20 to 210° F • Maximum working pressure: 130 PSI • Pumps can operate bidirectionally (reversible) This Oberdorfer CB9000L is the drop in replacement for models C4K and C4V. It can also be considered as replacements for models 4KHK4 and 4KHJ7. This self-priming, positive displacement, external rotary gear pedestal pump is ideal for oil based fluids in a wide range of light-duty commercial, industrial, marine, and agricultural applications. It is for use with particulate free and non-abrasive high lubricating oil-based fluids compatible with iron and steel. Not to be used with water-based fluids. Line mounted pressure relief valves are recommended to protect downstream equipment. The pump should be mounted on a rigid base and properly aligned with the motor. Direct drive via flexible shaft coupling is the preferred method. When a belt drive is needed, additional support is necessary to absorb the added pulley load.

Oberdorfer 109MB Series Centrifugal Pump FEATURES Pump Body: Bronze Ports: Inlet: 1 1/4" NPT Outlet: 1" NPT Flow: 80 GPM Max Pressure: to 19 PSI, 45 feet of head Impeller: Centrifugal Shaft Seal: Teflon Barrier Seal to Protect Motor Bearings. Carbon Face Mechanical Pump Seals. Buna Std., Viton and Teflon available. Shaft: 416 Stainless Steel is standard, Monel Shaft available for Marine Use Motor / Drive: Pump heads mount to standard footed NEMA 56J jet pump motors. A wide variety of motors are available and we can assemble for you.     APPLICATIONS / CHARACTERISTICS Oberdorfer™ centrifugal pumps have a single rotating metal impeller. Liquid enters at the center and is thrown outward radially by centrifugal force. The impeller is not in contact with other pump parts resulting in quiet, efficient, pumping action. The flow produced is not positive which permits the discharge line to be shut off completely without danger of overloading motors or bursting lines. Consequently a relief valve is not required. The liquid flow varies directly as the pump speed—the higher the speed the greater the flow. Horsepower required varies directly as flow and pressure. Maximum horsepower is required with a wide open discharge line. This is the point of maximum flow. With a throttled discharge, the flow decreases at a greater rate than the pressure increases thereby requiring less horsepower at the higher pressures. This is known as an “unloading” feature of the pump. FEATURES Rugged Bronze Construction A Standard in the Marine Air Conditioning Industry Extremely Quiet Operation O-Ring Housing seal eliminates gasket problems Polytetrafluoroethylene (PTFE) Barrier Seal to protect motor bearings Handles Contaminated Liquids Discharge port orientation flexibility-8 positions Mechanical Seal - Carbon/Ceramic, Nitrile - standard, Fluoroelastomer (S10) optional, Polytetrafluoroethylene (PTFE)(S11) optional Pump Heads mount to standard footed Nema 56J Jet Pump Motors Shafts: 416 Stainless, Nickel Alloy, or 316 Passivated Stainless Multiple motor options available For Industrial Version - see Model 700 series DRIVE This close-coupled pump uses a standard NEMA C-Flange Jet Pump Motor with weld-on base and threaded shaft end to accept the pump impeller. Single phase motors are nonreversible and are wired for the proper pump rotation which is counter-clockwise looking at the inlet end of the pump. (See the dimensional drawing.) Three phase motors must be checked out for proper rotation when the pump is installed.  Interchanging of any 2 wires in a 3-phase system will reverse motor rotation.  LIQUIDS & TEMPERATURES The special pump alloys used provide corrosion resistance to many liquids including water, water solutions, and a wide range of commercial chemicals. Questions as to the chemical compatibility of special liquids should be referred to the factory. The pump uses a mechanical type shaft seal with a Nitrile rubber element. It is suitable for water, oils, and some mild solvents and it is limited to 212oF and 75 P.S.I. Fluoroelastomer (S10) seals and Polytetrafluoroethylene (PTFE) (S11) seals are available for severe solvents and difficult chemicals. Viscous liquids with a maximum viscosity of 2000 Saybolt Seconds Universal can be pumped. However, when pumping viscous liquids as compared with water, a reduction in flow and pressure occurs and the required horsepower rate increases.  Liquids heavier than water require additional horsepower in direct proportion to the increase in specific gravity. Liquids contaminated with small solids or abrasives can be handled, but a reduction in mechanical seal life must be expected.  SUCTION LIFT These centrifugal pumps are not self-priming. They must be installed below the liquid level so that the liquid flows to the pump by gravity (flooded suction). However, if a foot valve is used at the beginning of the suction line and all air is bled from the pump by manual priming, the pump will lift on the suction side up to 15 feet. Such a system relies entirely on a non-leaking foot valve for starting capability.   Will Handle Contaminated Liquids. Extremely Quiet. A Standard in the Marine Air Conditioning Industry.     109MB is Oberdorfers - Centrifugal Pump Head Only Bronze 1 1/4" X 1"NPT  

Oberdorfer Pump 800B Ped Mnt Brz 1 1/4 X 1 Oberdorfer™ centrifugal pumps have a single rotating metal impeller. Liquid enters at the center and is thrown outward radically by centrifugal force. The impeller is not in contact with other pump parts resulting in quiet, efficient, pumping action. The flow produced is not positive which permits the discharge line to be shut off completely without danger of overloading motors or bursting lines. Consequently a relief valve is not required. The liquid flow varies directly as the pump speed--the higher the speed the greater the flow. Horsepower required varies directly as flow and pressure. Maximum horsepower is required with a wide open discharge line. This is the point of maximum flow. With a throttled discharge, the flow decreased at a greater rate than the pressure increases thereby requiring less horsepower at the higher pressures. This is known as an “unloading” feature of the pump.  Silent, efficient, centrifugal pumping is ideal for convenient equipment location in offices, laboratories, public areas, and living quarters. Long trouble-free service life has made centrifugal pumps acceptable for industrial uses or wherever clean or contaminated liquid is to be transferred or handled. The 800B centrifugal pump has external ball bearings isolated from the liquid being pumped. The ball bearings are grease sealed for life requiring no maintenance.     FEATURES Bronze Construction Heavy Duty Ball Bearings Designed for Pulley Drive Mechanical Seal Quiet Operation Handles Contaminated Liquids No Lubrication Required Closed Impeller -- High Discharge Pressure DRIVE The pedestal centrifugal pumps can be direct driven by electric motors and gasoline engines or pulley driven at intermediate speeds as listed in the capacity chart above.    LIQUIDS & TEMPERATURES Because centrifugal pumps are more efficient at higher shaft speeds, pumping of viscous or thick liquids is difficult. It is possible to lose as much as 40% pump performance when attempting to pump liquids of viscosity equal to S.A.E. 30 oil at room temperature. S.A.E. 30 oil at room temperature has a viscosity of 2000 Saybolt Seconds Universal. More viscous liquids are not recommended for centrifugal pumps.   Heavy liquids can be pumped; however, they demand more horsepower in direct ratio to the weight of water. For example, carbon tetrachloride has a specific gravity of 1.6 which means it is 1.6 times heavier than water and the horsepower required is 1.6 times water horsepower.   SUCTION LIFT This centrifugal pump is not self priming. Normally these pumps must be installed below the liquid level so that the liquid flows to the pump by gravity. However, if a foot valve is used at the beginning of the suction line and all air is bled from the suction line and pump by careful manual priming, these pumps will lift liquid on the suction side up to 15 ft. Such a system is only as positive as the ability of the foot valve to seal and keep the suction line and pump full of liquid. If the foot valve should leak, the pump will not prime. 

OBERDORFER N9000L PEDESTAL MOUNT GEAR PUMP Pump housings and gears are made of top quality bronze, shafts are 303 stainless steel. Bearings are made of high performance carbon-graphite material selected for wear resistance and long service life. Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid relatively unaffected by the backpressure in the discharge line. Shaft speed and flow are directly proportional.   DRIVE Either direct drive with flexible coupling or pulley drive can be used. Make sure both flexible coupling halves are properly aligned. When using a pulley, do not over tighten the belt. Also, to absorb belt side thrust at higher pressures and larger size pumps, an external ball bearing support is recommended - consult factory.   LIQUIDS & TEMPERATURES Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. These positive displacement pumps have tight tolerances. Fine abrasives like sand, silt, or powders in suspension will accelerate pump wear and reduce throughput. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified (see chemical compatibility or check factory). When possible, flush the pump after each usage. Temperature extremes are detrimental to service life and should be avoided. Basic metals of construction allow a temperature range of -40°F to 400°F. Some lip and mechanical seal elastomers have a limit of 212°F. Allowing a liquid to freeze in the pump can cause damage.   SUCTION LIFT Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet. Though gear pumps are self priming, a foot valve is recommended. If possible, wet the gears with liquid to be pumped for the first dry start. Liquid retained in the system and gear chambers serves to “wet” the pump on subsequent starts.

Oberdorfer N1000 Series Gear Pump FEATURES Pump Body: Bronze Ports: 1/4" NPT Flow: 2.1 GPM Max Pressure: 150 PSI Max Bearings: Heavy Duty Carbon Bearings (Self Lubricating) Gears: Special Cast Bronze Helical Gears Shaft Seal: Formed Ring Seal Packing Standard. Optional Lip Seals or Mechanical Seals in Buna or Viton. Shaft: Stainless Steel Shafts Motor / Drive: Either direct drive with flexible coupling or pulley drive can be used. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE PEDESTAL MOUNT ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.    Oberdorfer Gear Pump, Bronze, 1/4"NPT Ports, Buna Lip Seal  

Oberdorfer N1000 Series Gear Pump FEATURES Pump Body: Bronze Ports: 1/4" NPT Flow: 2.1 GPM Max Pressure: 150 PSI Max Bearings: Heavy Duty Carbon Bearings (Self Lubricating) Gears: Special Cast Bronze Helical Gears Shaft Seal: Formed Ring Seal Packing Standard. Optional Lip Seals or Mechanical Seals in Buna or Viton. Shaft: Stainless Steel Shafts Motor / Drive: Either direct drive with flexible coupling or pulley drive can be used. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE PEDESTAL MOUNT ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet. Oberdorfer Gear Pump, Bronze, 1/4"NPT Ports, Packed Seal      

Oberdorfer N1000 Series Gear Pump FEATURES Pump Body: Bronze Ports: 1/4" NPT Flow: 2.1 GPM Max Pressure: 150 PSI Max Bearings: Heavy Duty Carbon Bearings (Self Lubricating) Gears: Special Cast Bronze Helical Gears Shaft Seal: Formed Ring Seal Packing Standard. Optional Lip Seals or Mechanical Seals in Buna or Viton. Shaft: Stainless Steel Shafts Motor / Drive: Either direct drive with flexible coupling or pulley drive can be used. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE PEDESTAL MOUNT ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.   Oberdorfer Gear Pump, Bronze, 1/4"NPT Ports, Buna Lip Seal, Relief Valve  

Oberdorfer N1000 Series Gear Pump FEATURES Pump Body: Bronze Ports: 1/4" NPT Flow: 2.1 GPM Max Pressure: 150 PSI Max Bearings: Heavy Duty Carbon Bearings (Self Lubricating) Gears: Special Cast Bronze Helical Gears Shaft Seal: Formed Ring Seal Packing Standard. Optional Lip Seals or Mechanical Seals in Buna or Viton. Shaft: Stainless Steel Shafts Motor / Drive: Either direct drive with flexible coupling or pulley drive can be used. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE PEDESTAL MOUNT ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet. Oberdorfer Gear Pump, Bronze, 1/4"NPT Ports, Packed Seal, Relief Valve  

Oberdorfer N991-32 Gear Pump Peo 3/8" Brz Buna FEATURES Pump Body: Bronze Ports: 3/8" NPT Flow: 3.6 GPM Max Pressure: 100 PSI Max Bearings: Carbon Graphite Bearings, Self-Lubricating Gears: Durable bronze spur gears Shaft Seal: Buna Lip Seal Standard, Optional Viton Lip Seal. Shaft: 303 Stainless Steel Shafts Motor / Drive: Compact close-coupled design attaches to AC or DC motors with adaptor brackets. We have many motor options and can assemble for you   APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.   Oberdorfer- Gear Pump Head Only, Bronze, 3/8"NPT Ports, Buna Lip Seal  

Oberdorfer N1000 Series Gear Pump FEATURES Pump Body: Bronze Ports: 1/4" NPT Flow: 2.1 GPM Max Pressure: 150 PSI Max Bearings: Heavy Duty Carbon Bearings (Self Lubricating) Gears: Special Cast Bronze Helical Gears Shaft Seal: Formed Ring Seal Packing Standard. Optional Lip Seals or Mechanical Seals in Buna or Viton. Shaft: Stainless Steel Shafts Motor / Drive: Either direct drive with flexible coupling or pulley drive can be used. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE PEDESTAL MOUNT ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.    Oberdorfer Gear Pump, Bronze, 1/4"NPT Ports, Viton Lip Seal  

Oberdorfer N1000 Series Gear Pump FEATURES Pump Body: Bronze Ports: 1/4" NPT Flow: 2.1 GPM Max Pressure: 150 PSI Max Bearings: Heavy Duty Carbon Bearings (Self Lubricating) Gears: Special Cast Bronze Helical Gears Shaft Seal: Formed Ring Seal Packing Standard. Optional Lip Seals or Mechanical Seals in Buna or Viton. Shaft: Stainless Steel Shafts Motor / Drive: Either direct drive with flexible coupling or pulley drive can be used. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE PEDESTAL MOUNT ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.   Oberdorfer Gear Pump, Bronze, 1/4"NPT Ports, Viton Lip Seal, Relief Valve  

Oberdorfer N992-S5 Gear Pump Peo 3/8 Viton FEATURES Pump Body: Bronze Ports: 3/8" NPT Flow: 4.4 GPM Max Pressure: 150 PSI Max Bearings: Carbon Graphite Bearings, Self-Lubricating Gears: Durable bronze helical gears Shaft Seal: Buna Lip Seal Standard, Optional Viton Lip Seal. Shaft: 303 Stainless Steel Shafts Motor / Drive: Compact close-coupled design attaches to motors with adaptor brackets. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.   Oberdorfer Gear Pump Head Only, Bronze, 3/8"NPT Ports, Viton Lip Seal  

Oberdorfer N992-37-F30 Gear Pump 3/8" 115V W/ FEATURES Pump Body: Bronze Ports: 3/8" NPT Flow: 5.9 GPM Max Pressure: 150 PSI Max Bearings: Carbon Graphite Bearings, Self-Lubricating Gears: Durable bronze helical gears Shaft Seal: Buna Lip Seal Standard, Optional Viton Lip Seal. Shaft: 303 Stainless Steel Shafts Motor / Drive: Compact close-coupled design attaches to motors with adaptor brackets. We have many motor options and can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED ROTARY GEAR PUMPS Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.     Oberdorfer Gear Pump, Bronze, 3/8"NPT Ports, Reversible 1/3HP 115V TEFC Motor