ProSport Cup Holder Power Inverter Up to 150 Watts of AC Power Fully Automatic, Electronic Power Inverters Converts 12-volt battery power to 110V AC up to 150 watts. Extruded aluminum case High surge capacity Power/status LED indicators Standard 110v AC receptacle Output short and input polarity protection Low battery shutdown Over-temperature and overload protection WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Eskimo Cup Holder - 12VDC  The Dometic Eskimo Cup is a thermoelectric refrigerated cup holder. It is designed to accommodate mounting into surfaces of various thicknesses. A polished marine-quality 316 stainless-steel trim ring finishes the surface installation and is accented with two blue LED interior lights. Features: Keeps cold beverages chilled while you drink them, even on a hot day Holds beverage containers up to 20 ounces (591 ml) Replaces most standard cup holders and is easy to install Polished 316 stainless steel trim ring Blue LED interior lights DC-powered premium thermoelectric Peltier cooling element Easy to keep clean with a non-stick aluminum surface and built-in drain Electronics are completely sealed for protection against salt spray Safety features include a low-voltage cut off to avoid a dead battery, a high-voltage cut off to prevent damage to the unit, a high-heat cut-off, and an in-line fuse 4" recessed cup holder Powered by the house battery *Sold as an Individual WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm, and Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

keywords: ProMariner, ProSport, GEN 2, ProMariner ProSport GEN 2, invertor, charger

Plastic Rod & Cup Holder Backing Plate for Round Rod/Cup Only for 3-3/4" Holes Threaded Backing Plates for replacing existing ø3-3/4 cup holders with ROUND ABS PLASTIC Combination Rod & Cup Holders. Screws are included. For use with Round Top ABS Plastic Only in a ø3-3/4 existing hole.

Stainless Steel Rod & Cup Holder Backing Plate for Round Rod/Cup Only for 3-3/4" Holes Threaded Backing Plates for replacing existing ø3-3/4 cup holders with round SST plastic combination rod and cup holders.  For use with round top SST plastic only in a ø3-3/4 existing hole. Features: Screws are included

Clamp-On Rail Mounted Cup Holder - Small for Up to 1-1/4" Rail - Grey Camco's Clamp-On Rail Mounted Cup Holder provides a secure location to keep your beverage. It is a great addition to any boat with 3/4-inch to 1-1/4-inch rails. The secure clamp assembly keeps the cup holder in place with the help of tension adjustment screws. Swivel mount allows you to install on any angle rail keeping your cup holder level and in place. The cup holder is constructed of a durable, UV-resistant polymer and fits most standard sized drinks, cups, cans, bottles and tumblers. Features: The Perfect Boating or RV Accessory: Provides a secure location to keep your beverage; Cup holder mounts to 3/4-inch to 1-1/4-inch boat rails Compatibility: Fits most standard cups, cans, bottles and tumblers Swivels to Any Angle: Swivel mount allows you to install on any angle rail keeping your cup holder level and in place Durable Construction: Constructed of a durable, UV-resistant polymer Color: Grey

RAM® X-Grip® with RAM-A-CAN™ II Cup Holder Mount for 7"-8" Tablets The RAP-299-3-UN8U consists of the RAM-A-CAN™ cup holder base, double socket system, and universal spring-loaded X-Grip® cradle for 7"-8" tablets. The cup holder base includes a 6" flex mounting feature. A durable composite shell construction and soft fins that can be trimmed to fit make the cup holder mount one of the most portable and versatile “Go Anywhere” products offered. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles.  The included X-Grip® cradle has a clean and clever four-leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring-loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your tablet. The perfect complement to the modern sleek interior of today's vehicles, the RAM X-Grip® is the cell phone cradle evolved. The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.   Specifications: Hardware Included: Assembly Hardware, (1) Optional Tether, (1) Glue Tube for Rubber Caps Product Dimensions: Overall Height: 10.8"  Holder Dimensions: Width Range: 2.5" - 5.75", Depth Range: .875" max Wedge Dimensions: Fits cup holders between 2.57" - 3.5" inside diameter Socket To Socket Length: 3" Ball Size: B Size (1") Weight Capacity: Standard Use: 2 lbs, Heavy-Duty Use: 1 lb Packaging Type: Polybag Weight: 1.83 lbs.

Sandbar Slug Portable Cup Holder Portable Cup Holder Features: Easily adjusts for 15° and 30° rod holders Keeps your drinks readily available Add extra drink holders in an instant Perfect for the sandbar

RAM-A-CAN™ II Universal Cup Holder Base with Double Ball Mount The RAP-299-3-B-102U consists of a double socket arm, two diamond bases and RAM-A-CAN™ II cup holder base. The diamond bases measure 2.43" x 1.31" diamond base and contain two holes 1.912" from center to center, positioned at both ends of the diamond base. The hole pattern found on the diamond bases will connect to many RAM cradles, as well as third party cradles including mounts with the industry standard AMPS hole pattern. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both socket ends of the arm. The RAM-A-CAN™ II cup holder base serves as a mounting point for the diamond base. Compatible with any vehicle cup holder with an inside diameter range of 2.57" to 3.5". Specifications: Material: High Strength Composite Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag

Clamp-On Rail Mounted Cup Holder - Large for Up to 2" Rail - White Camco's Clamp-On Rail Mounted Cup Holder provides a secure location to keep your beverage. It is a great addition to any boat with 1-1/2-inch to 2-inch rails. The secure clamp assembly keeps the cup holder in place with the help of tension adjustment screws. Swivel mount allows you to install on any angle rail keeping your cup holder level and in place. The cup holder is constructed of a durable, UV-resistant polymer and fits most standard sized drinks, cups, cans, bottles and tumblers. Features: The Perfect Boating or RV Accessory: Provides a secure location to keep your beverage; Cup holder mounts to 1-1/2-inch to 2-inch boat rails Compatibility: Fits most standard cups, cans, bottles and tumblers Swivels to Any Angle: Swivel mount allows you to install on any angle rail keeping your cup holder level and in place Durable Construction: Constructed of a durable, UV-resistant polymer Color: White

Clamp-On Rail Mounted Cup Holder - Small for Up to 1-1/4" Rail - White Camco's Clamp-On Rail Mounted Cup Holder provides a secure location to keep your beverage. It is a great addition to any boat with 3/4-inch to 1-1/4-inch rails. The secure clamp assembly keeps the cup holder in place with the help of tension adjustment screws. Swivel mount allows you to install on any angle rail keeping your cup holder level and in place. The cup holder is constructed of a durable, UV-resistant polymer and fits most standard sized drinks, cups, cans, bottles and tumblers. Features: The Perfect Boating or RV Accessory: Provides a secure location to keep your beverage; Cup holder mounts to 3/4-inch to 1-1/4-inch boat rails Compatibility: Fits most standard cups, cans, bottles and tumblers Swivels to Any Angle: Swivel mount allows you to install on any angle rail keeping your cup holder level and in place Durable Construction: Constructed of a durable, UV-resistant polymer Color: White

Clamp-On Rail Mounted Cup Holder - Large for Up to 2" Rail - Grey Camco's Clamp-On Rail Mounted Cup Holder provides a secure location to keep your beverage. It is a great addition to any boat with 1-1/2-inch to 2-inch rails. The secure clamp assembly keeps the cup holder in place with the help of tension adjustment screws. Swivel mount allows you to install on any angle rail keeping your cup holder level and in place. The cup holder is constructed of a durable, UV-resistant polymer and fits most standard sized drinks, cups, cans, bottles and tumblers. Features: The Perfect Boating or RV Accessory: Provides a secure location to keep your beverage; Cup holder mounts to 1-1/2-inch to 2-inch boat rails Compatibility: Fits most standard cups, cans, bottles and tumblers Swivels to Any Angle: Swivel mount allows you to install on any angle rail keeping your cup holder level and in place Durable Construction: Constructed of a durable, UV-resistant polymer Color: Grey

Cup Holder - 316 Stainless Steel Features: Stainless Steel Cup Holder @3.25ID Matches our ELITE Series Rod & Cup Holders Cutout Diameter: ø3.5” Flange Diameter: 4.75″ Ø1/2 Drain Barb Adhesive Tape / Gasket Installation – Included 316L Stainless Steel

Stubby Cup Holder Mount with Double Socket Arm The RAM Stubby™ cup holder base is a low-profile option of our cup holder mounting base. The durable composite shell construction and flexible support fins can be trimmed to size make this cup holder base a portable and versatile solution. The mount is designed with a patented RAM 1" diameter rubber ball and this kit includes a standard-length arm so that any of your existing device cradles can be used with this versatile base. The RAM ball and socket system allows for articulation at both ends of the double socket arm creating almost infinite adjustment and perfect viewing angles. Compatible with any vehicle cup holder with an inside diameter range of 2.57" to 3.5". Specifications: Material: High Strength Composite Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag.

RAM® X-Grip® Large Phone Mount with RAM® Stubby™ Cup Holder Base Sometimes, it's all about the design. If you are looking for a compact mount for your cell phone without that cookie cutter shape, you've found it. The RAM X-Grip® has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. This mount comes with the RAM Stubby™ cup holder mount. The durable composite shell construction and flexible support fins can be trimmed to size make this cup holder base a portable and versatile solution. The RAM ball and socket system allows for articulation at both ends of the double socket arm creating almost infinite adjustment and perfect viewing angles. Compatible with any vehicle cup holder with an inside diameter range of 2.57" to 3.5". The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.  Specifications: Purchase Includes: (QTY. 1) Optional Tether Included Cradle Dimensions: Minimum Width = 1.75" (Minimum Height = 5.5") Maximum Width = 4.5" (Minimum Height = 3.25") Depth = 0.875" Material: High Strength Composite & Stainless Steel Ball Size: B Size 1" Rubber Ball Note: The "U" in the part number reflects product packaged in poly bag. RAM highly recommends using the provided Tether for all open cockpit applications while using this product. Weight: 1.55 lbs.