|
Flotec FP3212 3-Wire 4 Inch Submersible Well Pump, 230 Volts 1/2 HP, 10 GPM
4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.
KEY FEATURES
For 4" inside diameter or larger wells
Pumps from depths of 150ft
Floating Stack Design for sand resistance and reduced sand locking
Corrosion-resistant stainless steel pump and motor housing
3 year limited warranty
HORSEPOWER: 1/2
PERFORMANCE SERIES: 10 GPM
VOLTAGE: 230v, 60 Hz
NUMBER OF WIRES: 3 plus ground
BODY CONSTRUCTION: Stainless steel
MAXIMUM CAPACITY: 14 GPM
OPERATING RANGE: 20' to 150'
MAXIMUM DEPTH-TO-WATER: 150'
MAX PSI: 105 psi
PUMP DIAMETER: 3.78"
DISCHARGE PIPE SIZE: 1-1/4" NPT
RECOMMENDED BREAKER: 10 amp
|
588.75 |
|
|
Flotec FP2212 2-Wire 4 Inch Submersible Well Pump, 230 Volts 1/2 HP
4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.
KEY FEATURES
For 4" inside diameter or larger wells
Pumps from depths of 150ft
Floating Stack Design for sand resistance and reduced sand locking
Corrosion-resistant stainless steel pump and motor housing
3 year limited warranty
HORSEPOWER: 1/2
PERFORMANCE SERIES: 10 GPM
VOLTAGE: 230v, 60 Hz
NUMBER OF WIRES: 2 plus ground
BODY CONSTRUCTION: Stainless Steel
MAXIMUM CAPACITY: 13.6 GPM
OPERATING RANGE: 20' to 150'
MAXIMUM DEPTH-TO-WATER: 150'
MAX PSI: 105 psi
PUMP DIAMETER: 3.78"
DISCHARGE PIPE SIZE: 1-1/4" NPT
RECOMMENDED BREAKER: 10 amp
|
593.25 |
|
|
Flotec 3-Wire 4 Inch Submersible Well Pump, 230 Volts 1.5 HP, 10 GPM
4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.
KEY FEATURES
For 4" inside diameter or larger wells
Pumps from depths of 300ft
Floating Stack Design for sand resistance and reduced sand locking
Corrosion-resistant stainless steel pump and motor housing
WARRANTY
3 year warranty
HORSEPOWER: 1-1/2
PERFORMANCE SERIES: 10 GPM
VOLTAGE: 230v, 60 Hz
NUMBER OF WIRES: 3 plus ground
BODY CONSTRUCTION: Stainless Steel
MAXIMUM CAPACITY: 16 GPM
OPERATION RANGE: 40' to 300'
MAXIMUM DEPTH-TO-WATER: 300'
MAX PSI: 170 psi
PUMP DIAMETER: 3.78"
DISCHARGE PIPE SIZE: 1-1/4"
|
1510.56 |
|
|
Flotec FP2122 Submersible Well Pump 4"
Flotec Submersible Well Pump, for 5" or Larger Wells, Stainless Steel Pump and Motor Housing, 7GPM Series, 2 Wire, 3/4HP 230V, 1-1/4”NPT Port, Water Filled Submersible Motor, Built-in Check Valve, No Control Box Required
|
650.30 |
|
|
Flotec FP2112 Submersible Well Pump 4"
Flotec Submersible Well Pump, for 5" or Larger Wells, Stainless Steel Pump and Motor Housing, 7GPM Series, 2 Wire, 1/2HP 230V, 1-1/4”NPT Port, Water Filled Submersible Motor, Built-in Check Valve, No Control Box Required
|
512.29 |
|
|
Iwaki WMD-30RLZT, 3/4 inch MPT in/outlet 270gph 120v
Iwaki WMD 30RLZT Water Pump
American motor high pressure water rated pump
3/4 inch MPT inlet and outlet.
1/16 HP Motor output.
3150 RPM motor speed.
120 volts
1.00 amps.
Max flow 4.5 GPM.
270 GPH
Max head 36.1 ft.
Max system pressure 24.20 psi.
WMD pumps have American Made Motors
MD pumps have Japanese Made Motors
RLT pumps are for pressure applications
RZT pumps are for very high pressure applications
RLXT pumps are for circulation and wet or dry return
|
377.52 |
|
|
Iwaki WMD-20RLZT, 3/4 inch MPT in/outlet 174gph 120v
Iwaki WMD 20RLZT Water Pump
American motor high pressure rated water pump.
3/4 inch MPT inlet and outlet.
1/38 HP Motor output.
3100 RPM motor speed.
120 volts
0.53 amps
Max flow 2.9 GPM.
174 GPH
Max head 22.6 ft.
Max system pressure 14.22 psi.
WMD pumps have American Made Motors
MD pumps have Japanese Made Motors
RLT pumps are for pressure applications
RZT pumps are for very high pressure applications
RLXT pumps are for circulation and wet or dry return
|
329.68 |
|
|
Flotec FP4105 Cast Iron Jet Pump 1/2 HP
New cast iron shallow well jet pump is ideal for wells with pumping levels of 25' or less. Self-priming after the pump housing is initially filled with water.
KEY FEATURES
Reliable performance at 25' depth to water or less
Maximum pressures of 63 PSI and maximum pumping capacities to 5.1 GPM
Pump housing is constructed of heavy-duty cast iron and is ready to install
115 volt 1/2 HP
Fan cooled, completely enclosed motor
1" Suction Port and 1" Discharge Port
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 5.6 GPM
FLOW at 10' LIFT and 40 PSI: 4.5 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 63 PSI
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 7.2 amps
VOLTAGE: 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
381.42 |
|
|
BURKS 24CT6M, Turbine Pump 115/230v 1"Ports
Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction.
Close Coupled to a 1/4 Horsepower, 1750 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
|
2118.60 |
|
|
Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9 GPM (shallow well setup)
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM (shallow well setup)
MAX LIFT: 25' w/ shallow well jet kit / 70' w/ deep well jet kit
MAX PSI: 62 psi (shallow well setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4"
MINIMUM SUCTION PIPE SIZE: 1-1/4"
DRIVE PIPE SIZE: 1"
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
516.00 |
|
|
Flotec FPZT7350 1/2 HP Zinc Body Submersible High Output Sump Pump, Vertical Switch
A ½ HP version of our highly engineered sump line – this pump moves up to 6,000 gallons per hour! The vertical switch allows this pump to fit in a sump basin as small as 10” wide.
FEATURES
Corrosion Resistant Zinc Construction - Dissipates heat quickly and extends motor life
Uni-Body Motor Housing - Eliminates leak points and maximizes pump life
Stainless Steel Fasteners and Hardware - Superior quality
Quadra SealTM Technology - Provides superior motor protection over single seal designs
Smooth Flow HydraulicsTM - Deliver high performance for demanding applications
Vertical Float Switch - Operates in 10” basins or larger
3 year limited warranty
BODY CONSTRUCTION: Zinc
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 6,000 GPH
FLOW at 10' LIFT: 4,140 GPH
SWITCH TYPE: Vertical Float
FLOAT SWITCH 'ON' LEVEL: 7-1/2"
FLOAT SWITCH 'OFF' LEVEL: 3"
MINIMUM SUMP DIAMETER: 10"
DISCHARGE PIPE SIZE: 1 1/2” NPT
MAXIMUM SOLIDS HANDLING SIZE: 3/8"
CORD LENGTH: 8'
VOLTAGE: 115 VAC, 60 Hz
|
338.52 |
|
|
Little Giant Condensate Pump 554425
Little Giant VCMA-20ULS Condensate Pump
Motor 115 Volts 1/30 hp high performance motor, ABS tank, motor cover, and volute, 1/2 gallon tank capacity Stainless steel shaft, Removable 3/8" (9.5 mm) barbed check valve, 3 inlet drain holes, Thermal overload protection
554425 For removal of condensate from an air conditioner, suitable for high efficiency, gas furnace condensation, and condensing boilers
|
112.32 |
|
|
Little Giant Condensate Pump 554435
Little Giant VCMA-20ULST Condensate Pump
Motor 115 Volts 1/30 hp high performance motor ABS tank, motor cover, and volute, 1/2 gallon tank capacity, Stainless steel shaft, Removable 3/8" (9.5 mm) barbed check valve, 3 inlet drain holes, Thermal overload protection
554435 For removal of condensate from an air conditioner, suitable for high efficiency, gas furnace condensation, and condensing boilers
|
117.78 |
|
|
Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP
This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less.
KEY FEATURES
Perfect for shallow wells (depth-to-water less than 25')
Thermoplastic construction for higher corrosion resistance
1-1/4" Suction / 1" Discharge
Comes with pre-wired 30/50 pressure switch
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8 GPM
FLOW at 10' LIFT and 40 PSI: 6.4 GPM
MAX LIFT: 25'
MAX PRESSURE: 77 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 9.4 amps
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
432.90 |
|
|
Flotec FP4112 Cast Iron Shallow Well Jet Pump 1/2 HP
Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less.
KEY FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install dual voltage (115v/230v) motor
1-1/4" NPT suction and 1" NPT discharge pipe sizes
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8.8 GPM
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM
MAX PSI: 56 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
MINIMUM SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.4 amps
VOLTAGE: 115v/230v (preset to 115v), 60 Hz
RECOMMENDED BREAKER: 15 amp
LIQUID TEMP RANGE: 32°F-140 °F (0°C-60 °C)
JET KIT: included
|
433.55 |
|