Diaphragm Pump Made of corrosion-proof marine plastic. Two position stainless steel handle and adjustable (Octagonal) frame permits up to 16 variations in stroke direction. Mounts vertically on bulkhead or horizontally on deck without the need for special brackets. Uses Beckson FH-1-1/2 or VCS-1-1/2 hose. Dimensions with handle removed: Length: 9" (23 cm) Width: 6-1/4" (16 cm) Height: 4-1/2" (12 cm) Pumps: 16 gal. minute (60 L) (1 L per stroke)

Bosworth 2800-B Guzzler Brz Peo 56C   Bosworth Diaphragm Pump End Only Guzzler Bronze, 13.4GPM, 2” Smooth Ports, 56C Motor Flange, Buna Flapper Valves and Diaphragm   GE-2600B Requires 1/2HP Motor

Gianneschi CB25/16B-B 230V 50Hz Mpu Gianneschi CB-25/16-B-B-230V, CB Series Centrifugal Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 1.1 KW (1.5 Horsepower), 2900 RPM, 230 volts AC, Single Phase. Inlet Port is 1-1/2 Inch BSP Inlet, Discharge Port is 1 Inch BSP Outlet.   Applications for the CB25/16BB230V include air conditioning systems, water supply, lifting fresh or salty water at sanitary plants, water circulations, increasing water pressure at water plants, pumping fresh water and seawater, and cooling and heating.

Raritan PHII PUMP Phii Pump Assy Complete

  Check all of your impellers contained within the engine cooling pumps, bilge pumps, ballast pumps, and so on.  One of the biggest contributors to impeller deterioration and damage is sitting idle in the same position for several months, so a proper check of the impeller(s) is vital to a reliable operation of the boat after storage and/or no operation.   Replacing an impeller is a fairly easy and straightforward process and one that you have probably done in the past. It is important to use the right tool to remove an impeller from the pump. Channel lock or needle-nose pliers are fine, but using an impeller removal tool is the best choice.  Never use a screwdriver to pry an impeller out of a pump; you could accidentally score the bronze housing which can lead to leaks.  Make sure you know how the impeller is being held in place.  Some are sealed to the shaft with an O-ring; others are held in place with a set screw and others with a c-clip.   Make sure to check the pump and the water lines for any trash or chunks of rubber that may have broken off from the impeller.  Even the smallest blockage can cause major engine cooling and overheating issues.  Also, remember to properly lubricate your new impeller with Vaseline or the lubricant included with the new impeller. This will reduce friction for a brand new impeller on a dry startup.   Most importantly, make sure you are using the right impeller for the application. We have seen many instances of people who have replaced an impeller with something that is close to the original, but not exactly right, and this can cause major problems for the engine once normal operation resumes.  You cannot match the size of the used impeller to a new one to determine the replacement, as a used impeller can be swollen and disfigured from its original specifications.  The best method is to obtain the impeller number off of the impeller itself, usually located on the edge of the shaft hole of the impeller, or obtain the part number of the pump, usually stamped into the bronze housing.   You can find just about every impeller that needs to be replaced at CLR Marine.  We carry Sherwood, Jabsco and Globe just to mention a few. We also carry many of the miner and major rebuild kits for many pumps.  A minor repair kit consists of the impeller and any gaskets or O-rings that may be needed to replace the impeller.  Our major rebuild kits include everything to rebuild that pump except for the shaft.  All kits are put together at time of order so you will always see the Quantity on Hand as 0.

Handy-Mate Utility Pump Beckson's Handy-Mate pumps can be used around the home, car, RV or anywhere to handle routine and emergency pumping jobs. They are designed to handle all the routine pumping jobs, plus the unusual ones. They can pump water out of bilges, sump tanks and from one tank to another, or pump oil from inboard or stern drive or engine crankcases when it needs changing. A tube is provided to insert into the dipstick hole and the oil is quickly pumped out. The especially versatile 216PC pumps come with a kit of tubes, hoses, reducing foot and adapter. The Handy Mate is made entirely of tough marine plastic. It will not rust or corrode, is non-sparking for safety, and requires no priming to start pumping action. The pump body has a diameter of 1-1/2" (38mm), and it is fitted with a comfortable molded handle for easy, no-strain operation. Features: Length: 16" (40.6cm) Diameter: 1-1/2" (38mm) Pumps: 10 oz./stroke Two intake tubes: 36" (91.4cm) long x 1/2' (13mm) 1/4" (7mm) x 36" (91.4cm) w/adptr Flexible hose for water discharge: 1-1/4" (45mm) x 24" (61cm) Red discharge tube for oil: 1-1/4" (45mm) x 10" (25mm) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pry-Out Deck Plates Beckson developed the first pry-out deck plate. These plates were designed with an extra heavy O-ring to assure a water tight fit. Plates are provided with non-skid or smooth surfaces for different installation requirements. The original was used to access the handle for Beckson's permanently mounted pump. The Beckson Diamond Pattern deck plate extends across the center, eliminating a ring around the edge that traps dirt and debris. Pry-out plates should be installed in areas where internal pressure (oil-canning) is not present. O.D.: 8-1/2" Hole Cut: 6-1/2" Passage: 6-3/16" Center: Smooth

Pry-Out Deck Plates Beckson developed the first pry-out deck plate. These plates were designed with an extra heavy O-ring to assure a water tight fit. Plates are provided with non-skid or smooth surfaces for different installation requirements. The original was used to access the handle for Beckson's permanently mounted pump. The Beckson Diamond Pattern deck plate extends across the center, eliminating a ring around the edge that traps dirt and debris. Our clear center plates permit observation of controls or gauges and visual inspection without the necessity of removing the plate. Pry-out plates should be installed in areas where internal pressure (oil-canning) is not present. O.D.: 8-1/2" Hole Cut: 6-1/2" Passage: 6-3/16" Center: Smooth

Pry-Out Deck Plates Beckson developed the first pry-out deck plate. These plates were designed with an extra heavy O-ring to assure a water tight fit. Plates are provided with non-skid or smooth surfaces for different installation requirements. The original was used to access the handle for Beckson's permanently mounted pump. The Beckson Diamond Pattern deck plate extends across the center, eliminating a ring around the edge that traps dirt and debris. Pry-out plates should be installed in areas where internal pressure (oil-canning) is not present. O.D.: 8-1/2" Hole Cut: 6-1/2" Passage: 6-3/16" Center: Dimple

Pry-Out Deck Plates Beckson developed the first pry-out deck plate. These plates were designed with an extra heavy O-ring to assure a water tight fit. Plates are provided with non-skid or smooth surfaces for different installation requirements. The original was used to access the handle for Beckson's permanently mounted pump. The Beckson Diamond Pattern deck plate extends across the center, eliminating a ring around the edge that traps dirt and debris. Pry-out plates should be installed in areas where internal pressure (oil-canning) is not present. O.D.: 8-1/2" Hole Cut: 6-1/2" Passage: 6-3/16" Center: Dimple

Pry-Out Deck Plates Beckson developed the first pry-out deck plate. These plates were designed with an extra heavy O-ring to assure a water tight fit. Plates are provided with non-skid or smooth surfaces for different installation requirements. The original was used to access the handle for Beckson's permanently mounted pump. The Beckson Diamond Pattern deck plate extends across the center, eliminating a ring around the edge that traps dirt and debris. Pry-out plates should be installed in areas where internal pressure (oil-canning) is not present. O.D.: 10" Hole Cut: 8-3/8" Passage: 8" Center: Smooth

Pry-Out Deck Plates Beckson developed the first pry-out deck plate. These plates were designed with an extra heavy O-ring to assure a water tight fit. Plates are provided with non-skid or smooth surfaces for different installation requirements. The original was used to access the handle for Beckson's permanently mounted pump. The Beckson Diamond Pattern deck plate extends across the center, eliminating a ring around the edge that traps dirt and debris. Our clear center plates permit observation of controls or gauges and visual inspection without the necessity of removing the plate. Pry-out plates should be installed in areas where internal pressure (oil-canning) is not present. O.D.: 10" Hole Cut: 8-3/8" Passage: 8" Center: Clear

Compact toilet handling and waste water pump Viking Power Vacuum The Viking Power Vacuum diaphragm pumps have been designed to meet the rigorous demands of the world's leading manufacturers of boats, recreational vehicles and busses. The Viking Power Vacuum has double check-valves and can therefore also be used in vacuum toilet systems. Naturally, pumping ordinary shower or sink drain water or bilge water is no problem for either pump. Like the Viking Power 16, this new pump has been engineered with a ball-bearing supported transmission for long service life. The pump can not only be run dry, it can also handle a mixture of air and water without difficulty. The Viking Power 32/Vacuum provides maximum flow of 32 liters per minute and is self-priming up to a height 3.5 (Vacuum) meters. Although powered by an electric motor, this pump can also be cranked by hand in an emergency. The pump has been designed to prevent the leakage of unpleasant odors; and the Viking Power 32/Vacuum can be installed in a variety of different positions. The Viking Power 32/Vacuum is built to last, yet priced competitively. Features Maximum flow 32 l/min Specifically engineered to pump black wastewater Uncompromising odor-prevention features Whisper quiet operation Self-priming High-impact glass-fiber reinforced nylon body Ball-bearing supported transmission Non-choke valves - no waste shredding required Pump head rotatable 360° Double check valves on Viking Power Vacuum Self-priming up to 2.5 meters (8.2 feet) Can be run dry and can pump air/water mixture Robust single diaphragm Electric motor with power-out, manual-crank backup Complies with ISO 15083 and small craft bilge pump Standard for vessels above 12 m (39.4 ft)

Thirsty-Mate Hand Pump with 20" Hose The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 18" Diameter: 1-1/4" Strokes/Gal: 10 Capacity: 6GM Hose Length: 20" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thirsty-Mate Hand Pump The Beckson THIRSTY-MATE hand pump is manufactured in the U.S.A. of the finest materials available. It is self-priming and very easy to clean. This hand pump will not rust or corrode or mar your boat. If your THIRSTY-MATE hand pump becomes clogged, simply remove the foot valve assembly and clean out the inside. Spare parts such as replacement foot valve assemblies and hoses are readily available. Features: Angled top sleeve Contoured red tee handle Non-conductive material Self-priming plunger valve Special polyvinyl grey body and shaft Removable foot valve for cleaning Self-priming Solvent welded construction Will withstand temperature to 120 degrees F (49 degrees C) Length: 24" Diameter: 1-3/4" Strokes/Gal: 6 Capacity: 10GM Hose Length: 24" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.