Cannon Rod Holder The Cannon Rodholder features a three-position rod-holding configuration to deliver the fastest baitcast or spinning rod pickup. A rear-position cradle holds baitcasting reels or spinning reels. The middle baitcasting cradle conforms to longer rod butts and shrtens the amount of rod extending through the back of the holder. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Extension Post f/Cannon Rod Holder - 2-Pack Features: Extends height of rod holder by 6" Allows forward & backward pivot adjustment Alignment key allows for 360° pivot while holding post securely in place

Allows rod holder to mount into the gunnel of the boat. Alignment key allows for 360 degree pivot while holding rod holder securely in place. Includes water-tight cap.

Bracket can be mounted on vertical or horizontal surface. Alignment key allows for 360 pivot while holding rod holder securely in place.

Rail Mount For mounting our single axis rod holder, this convenient rail mount attaches to either round or square rails. For 3/4" to 1-1/4"

Outrigger Rod Holder with Liner & Strap - Aluminum Features: Strong, Stylish and Functional Includes Liner and Strap Aluminum

DUAL AXIS ADJUSTABLE ROD HOLDERS DOWNRIGGER MOUNT Mount our dual axis rod holders between the mounting base and swivel base of your Cannon downrigger for unparalleled rod positioning. A pistol grip release allows for quick, one-handed angle changes, and the innovative ratcheting adjustment system allows you to easily pull the holder to a vertical position. Full 360 degree rotation makes it the ultimate fishing accessory. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Rod Holder - Medium - 0° - Stainless Steel The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years. Lee manufacturers of over 46 different models of flush mounted rod holders. Available in two sizes, Medium (2 in O.D.) and Heavy (2 1/4 in. O.D.) three different angles (0, 15 & 30 degree) in Stainless Steel. All of our Rod Holders, are polished by hand then electropolished Lee’s has the rod holder to suit any task.

Rod Holder - Heavy Duty - 0° - Stainless Steel The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years. Lee manufacturers of over 46 different models of flush mounted rod holders. Available in two sizes, Medium (2 in O.D.) and Heavy (2 1/4 in. O.D.) three different angles (0, 15 & 30 degree) in Stainless Steel. All of our Rod Holders, are polished by hand then electropolished Lee’s has the rod holder to suit any task.

NEW - Innovative Trolling System Puts You In Control No matter how you fish - or what your fish for - you can customize our new trolling system to fit your style. Our new rod holders feature a pistol grip design for one-handed adjustment of the rod angle and a ratcheting system for easy rod removal. Made of High-strength aluminum to withstand the punishment of big water use and can be changed out in a snap with our unique track system. Adjustable Rod Holder Single Axis This 10" holder utilizes 6 up and down locking positions, and delivers 90° of side-to-side rotation. A pistol grip release allows for quick, one-handed angle changes, and the innovative ratcheting adjustment system allows you to quickly pull the holder to a vertical position. Includes a UV-resistant end cap to protect rod and reel. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

NEW - Innovative Trolling System Puts You In Control No matter how you fish - or what your fish for - you can customize our new trolling system to fit your style. Our new rod holders feature a pistol grip design for one-handed adjustment of the rod angle and a ratcheting system for easy rod removal. Made of High-strength aluminum to withstand the punishment of big water use and can be changed out in a snap with our unique track system. Adjustable Rod Holder Dual Axis Experience 360° of rotation at the push of a button with this 10" holder. It features six up and down locking positions, a pistol grip release for quick, one-handed angle changes and a ratcheting adjustment system that allows you to quickly position the holder vertically. Includes a UV-resistant end cap to protect rod and reel WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Dual Rod Holder/Front Mount Front-mount rod holder fits all 1 5/16" diameter Cannon booms, including telescopic boom. Also fits several other downrigger makes. Each holder has a separate angle adjustment. Comes with two rugged rod tubes with gimbal and drain hole, two aluminum tube clamps, and Lexan® dual-mounting bracked. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Aluminum Clamp-on Rod Holders Model:  RA5001GL Color:   Gold Fits:      1.050" O.D. Pipe Mount:  Vertical JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don't like the position, simply move them. These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe. All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.

Aluminum Clamp-on Rod Holders Model:  RA5004SL Color:   Silver Fits:      1.900" O.D. Pipe Mount:  Vertial JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don't like the position, simply move them. These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe. All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.

Aluminum Clamp-on Rod Holders Model:  RA5201GL Color:   Gold Fits:      1.050" O.D. Pipe Mount:  Horizontal JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don't like the position, simply move them. These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe. All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.