Seal kits for Baystar and SeaStar helm pumps.

March 893-04 Brush 12V DC Pump Applications for the March 893-04 Magnetic Drive Pump include marine refrigeration and water displays. March Pump's industrial 893-04 is an American submersible seal-less centrifugal magnetic drive pump ideal for applications such as marine equipment. It is capable of generating a maximum flow of 2.7 gallons per minute at 1 foot, and its maximum head is 10.6 Feet (or around 4.5PSI). The 893-04 must be used submerged. The standard wet end (the materials that come into contact with the solution) is composed of Noryl, Nylon, Carbon/Teflon, Buna N, Stainless Steel, and Ceramic Magnet.  When submerged Epoxy, Delrin, and the motor leads are also in contact with the solution. The inlet connection is 0.375 inch female pipe thread, and the outlet is 0.375 inch smooth. The standard motor is a 0.006 Horsepower DC Brushtype Motor, available in 12 Volts.  The 12 Volt Motor has an operating range from 0 to 14 Volts.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 160 Fahrenheit or 71 Celsius. The March 893-04 centrifugal magnetic drive pump is capable of handling mild corrosive chemicals, acids, and solvents.     Max Flow 2.7 GPM 11 LPM Max Head 10.6 FT 3.3 M Power .006 HP .004 KW Electrical 12V Range 0-14 Submersible Yes   Type Centrifugal Mag Drive Inlet 3/8"FPT Outlet 3/8"OD Wet End Noryl (Front and Rear Housings), Nylon (Impeller), Carbon/Teflon (Thrust Washer), Buna N (O-Ring), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Pump must be used submerged When submerged, the following is also in contact with the solution Epoxy, Delrin, Motor Leads  

BURKS 23325-7.06, Wet End Kit for Series GA7-1-1/2

Xtreme Power Assist Steering is engineered to bring the smooth, easy control of electric power-assisted steering to a wide range of popular boats, including pontoons, runabouts, RIBS, aluminum fishing boats and center consoles without increasing the load on mechanical steering helm or cable. Steering effort is significantly reduced, providing a car-like driving experience. Once installed, the mechanical steering cable only turns the power assist unit, while the electric steering actuator actually turns the engine load. Engineered to fit a wide range of single engine, mechanically steered outboard boats from 90-200HP. Self-contained, plug-and-play system easily mounts to all major outboard brands and integrates with the boats existing mechanical steering. Built in Fail-Safe System automatically reverts to mechanical steering in the event of a system failure.

Specifically designed to be used on smaller commercial fishing vessels. Features stainless steel shaft, heavy duty shaft seal and wiper. Shaft and seal help protect the pump from the abrasive effects of sediment that is brought on board by the operator handling traps or pots. 1000 PSI relief valve setting. Adjustable stainless steel ORB O-ring fittings simplify installation and allow simple reorientation of fittings after installation. Anodized rear cover, anodized black port plugs.

Seal kits for Baystar and SeaStar helm pumps.

Adjustable stainless steel ORB O-ring fittings simplify installation and allow simple reorientation of fittings after installation. Anodized rear cover, anodized black port plugs. Designed specifically for SeaStar hydraulic steering systems.

Adjustable stainless steel ORB O-ring fittings simplify installation and allow simple reorientation of fittings after installation. Anodized rear cover, anodized black port plugs. Designed specifically for SeaStar hydraulic steering systems.

Adjustable stainless steel ORB O-ring fittings simplify installation and allow simple reorientation of fittings after installation. Anodized rear cover, anodized black port plugs. Designed specifically for SeaStar hydraulic steering systems.

Volvo tilt and trim motor. Includes hydraulic valve body and ring terminal ends.

Baystar Plus helm uses bearings to keep tolerances tighter, improving responsiveness and performance. Standard Baystar helm uses internal bushings. 5 turns, lock-to-lock. Adjustable stainless steel ORB O-ring fittings simplify installation and allow reorientation of fittings after installation. Anodized rear cover, anodized black port plugs. Requires 3" cut-out hole in dash.

Adjustable stainless steel ORB O-ring fittings simplify installation and allow simple reorientation of fittings after installation. Anodized rear cover, anodized black port plugs. Designed specifically for SeaStar hydraulic steering systems.

Baystar Plus helm uses bearings to keep tolerances tighter, improving responsiveness and performance. Standard Baystar helm uses internal bushings. 5 turns, lock-to-lock. Adjustable stainless steel ORB O-ring fittings simplify installation and allow reorientation of fittings after installation. Anodized rear cover, anodized black port plugs. Requires 3" cut-out hole in dash.

Repair parts for SeaStar hydraulic cylinders.

Repair parts for SeaStar hydraulic cylinders.