|
Universal Masthead Mount
Extend your WindTrak 10.Sport or WindTrak 15 vane away from masthead obstructions and turbulence. The 13" (33 cm) arm comes with hardware allowing side or top mounting and offset angles up to ±20 degrees. May be attached securely to flat, curved, vertical, horizontal, or inclined surfaces. Gain space aloft and improve mounting position of wind finders and other equipment. Mount on the back of the mast for easier viewing from the cockpit. The mount adapts to virtually every masthead situation.
Features:
Length 13" (33 cm)
Weight 3.2 oz (90 g)
Boom can be shortened if necessary; complete instructions included
Can be used with WindTrak Light #3200. Also accommodates Davis J-Base Mounts (using #10 stainless steel screws and nuts, not included)
|
37.50 |
|
|
Spare Vane Only f/WindTrak 10.Sport
|
18.76 |
|
|
J-Base for WindTrak 10.Sport for Side, Top or Front of Mast Mounting
Allows for side, top, or front mounting on most masts, on big boats or dinghies alike. Standard with the WindTrak 10.Sport, J-Base™ can be ordered as an option for WindTrak 15.
Standard with the WindTrak 10.Sport, J-Base™ can be ordered as an option for WindTrak 15. Allows for side, top, or front mounting on most masts, on big boats or dinghies alike. J-Base is made of glass filled polycarbonate, 2″ (5 cm) long. Includes stainless steel set screw and (2) #10 self-tapping screws. Reduces overall weight by 15 grams when substituted for standard mounting base on WindTrak 15.
|
9.25 |
|
|
WindTrak 10 Sport Wind Vane
With the introduction of the WindTrak 10 Sport, WindTrak wind vanes continue to offer exceptional performance at the best value of any wind indicator worldwide. The secret is in the sapphire jewel suspension bearing, large fin-low inertia van, and easy-to-read, fully adjustable tacking tab system.
Reflector tape on the vane and tacking tabs make WindTrak 10 Sport easy to see day and night. WindTrak vanes are sturdy and when installed properly, offer many years of use. They have been wind tunnel tested to wind speeds of 80 knots! WindTrak 10 Sport has a 10" (25 cm) vane. Includes glass reinforced polycarbonate J-Base for side, top or front of mast mounting on most dinghies, smaller boats and sport boats. Stands just 9.25" (23.5 cm) tall and weighs 1.2 ounces (31 g).
|
33.76 |
|
|
RAM® X-Grip®Wheelchair Seat Track Mount for 9"-10" Tablets
This kit includes a C size RAM® diamond ball base with a universal hardware pack that accommodates the seat track on most major wheelchair brands, including Invacare, Permobil, and Quickie. With the included short single socket arm, pipe extension, and double socket arm, connect the RAM® X-Grip® universal holder for 9”-10” tablets. The spring-loaded RAM® X-Grip® provides a perfect fit for your tablet and can be easily adjusted to the ideal position.
Specifications:
Cradle Dimensions:
Minimum Width = 6.25"
Maximum Width = 8.1"
Depth = 0.875"
Maximum Length (using additional supports) = 10.25"
Included Mounting Hardware:
(QTY. 2) #10-32 x 1/2" Machine Screw
(QTY. 2) #10-32 T-Nut (3/8" x 5/8")
(QTY. 2) #10-32 T-Nut (1/2" x 1")
(QTY. 2) M4 x 12mm Machine Screw
(QTY. 2) M4 x 20mm Machine Screw
(QTY. 2) M4 Stainless Steel Washer
(QTY. 2) M4 Nylock Nut
Material: Powder Coated Marine Grade Aluminum & High Strength Composite
|
90.00 |
|
|
367 Universal Fishfinder Mount for Up to 9" Units
Features:
The Scotty Universal Sounder/Fishfinder Mount uses a new multi pattern universal top plate and the Scotty post mount design for quick removal and adjustable rotation
Simply fasten your sounder bracket to the top plate, then lock down the sounder mount into your favorite Scotty post mounting system
Only intended for use with Fishfinders and other marine electronics
|
23.64 |
|
|
Pole Mount for MSC 10
Mount your compatible device and route an NMEA 2000® cable through this 1-inch (outside diameter) pipe-threaded pole mount. This version allows for secure mounting and alignment of your MSC-10 Marine Satellite Compass.
|
53.99 |
|
|
GM S10 Gimbal Mount for SOLIX 10
The GM S10 is a metal gimbal mount for all SOLIX 10 Series products. This includes the gimbal mount, gimbal mounting knobs, and hardware.
Features:
Compatible with: All SOLIX 10 Series
1-Year Limited Warranty
|
54.54 |
|
|
J-BASE for WindTrak 15
This optional mount for WindTrak 15 provides more versatility and reduces overall weight aloft by 15 grams when substituted for standard WindTrak 15 mounting base.
The J-Base comes with two #10 (5 mm) selftapping screws. Drill a pilot hole in mast, apply silicone sealant or Locktite® and screw into mast. Installation of J-Base can also be accomplished by tapping the mast for 3/16" (5 mm) machine screws or by using epoxy putty to affix base to the mast
|
9.25 |
|
|
Spare Vane Only f/WindTrak 15
|
30.00 |
|
|
Universal Mast Mount Platform for 12"18" Radome
Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast.
Adjustable
Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast.
Incredible Strength
The solid under body construction not only greatly improves strength but also hides radar cables. On certain models.
Accessories
Pre-drilled under body allows for flood lights or horns to be mounted on certain models.
Compatible Manufacturers:
Furuno
JRC
Koden
Lorenz
Sitex
VDO
|
374.40 |
|
|
Masthead Light f/Sail or Power Less Than 20M - 12VDC - Black Base Mount/White Light
Features:
Black Plastic with Stainless Steel Mounting Bracket
Bulb Included
Certified for use on Sail or Power Driven Vessels Under 20 Meters (65.6 ft.) in Length.
3 Miles Visibility
12VDC
|
104.40 |
|
|
RAM® X-Grip® with RAM® Pod™ I Vehicle Mount for 12" Tablets
The RAM-B-316-1-UN11U consists of the RAM POD I universal No-Drill® vehicle base, 18” rigid aluminum rod, socket system and universal X-Grip® clamping cradle for 12" tablets. The base of the mount connects to your seat rail without any drilling necessary. The 18" rigid aluminum rod can be bent to position your device to its optimum viewing location. The X-Grip® clamping cradle consists of a composite spring loaded cradle, expandable grip arms and additional bottom support keeper. Included are extra easy access grip knobs, located on the back of the cradle for quick release of your tablet. The X-Gripclamping cradle expands and contracts for perfect fit of most 12" tablets with or without sleeves, as well as some smaller tablets. Please verify dimensions of your tablet below for compatibility with the X-Grip®. The X-Grip® cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. The RAM-HOL-UN11U is compatible with the iPad Pro WITHOUT CASE ONLY.
Features:
Universal vehicle mount attaches to seat rail without any drilling necessary; 18" aluminum rod can be bent to your ideal position
Spring-loaded 'X' design with rubber caps sports great holding power without hiding your tablet; fits most 12" tablets
Made of powder-coated, marine-grade aluminum and high-strength composite for durability and reliability in the most demanding environments
Backed by a lifetime warranty
Specifications:
Hardware Included: Assembly Hardware
Holder Dimensions: Max Height: 10.25" (using optional supports), Width Range: 7.25" - 8.75", Max Depth: .875"
Ball/Socket Size: B Size (1")
Materials: Marine-grade aluminum, High strength composite
|
131.74 |
|
|
368 Universal Sounder Mount
Scotty's Universal Sounder Mount uses a multi pattern universal top plate and the Scotty post mount design for quick removal and infinitely adjustable rotation. Simply fasten your sounder bracket to the top plate, then lock down the sounder mount into your favorite Scotty mounting system. Locked, loaded and ready to start catching fish!
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
15.48 |
|
|
RAM Tab-Tite Universal Clamping Cradle f/Apple iPad w/LifeProof & Lifedge Cases
The RAM-HOL-TAB17U consists of a spring loaded back plate and custom support cups for 10" screen tablets WITH heavy duty cases. The spring loaded design makes it easy to load and unload your tablet, along with keeping it secure while on the go. Interchangeable cup ends are designed to optimize the functionality of your tablet, allowing access to audio jacks, usb, power, and other ports, your tablet can be used just as it was intended. Perfect for stationary or on the go applications, the RAM-HOL-TAB17U is just what you need to get the most out of your tablet.
The RAM Tab-Tite cradle is compatible with the following tablets:
10" Screen Tablets with LifeProof nüüd cases
10" Screen Tablets with Lifedge cases
10" Screen Tablets with heavy duty cases
The Tab-Tite cradle is compatible with any tablet or reader that will fit the dimensions listed below. It is important to verify the dimensions of your tablet when determining the overall size.
Tab-Tite Cradle Dimensions:
Height: 8.75" minimum to 10.75" maximum
Width: maximum to 8.25"
Depth: maximum to 1.1"
Tab-Tite Cradle Features:
1. Support cups contain open slots to accommodate for tablets of various sizes
2. Back plate can support various size support cups
3. Spring loaded tension provides secure support for your tablet
4. Spring loaded cradle allows for quick release of your tablet
5. High strength materials maximize longevity of cradle
6. Full access to all ports
7. Lifetime warranty
Material:
High Strength Composite
Note:
The "U" in the part number reflects product packaged in poly bag.
|
27.61 |
|