|
Water Booster System - 40PSI - 4.5GPM - 115V
The Flojet 2840 Series Booster Systems are designed to provide constant water pressure of 0 to 40 psi (0.7 to 2.7 bar) and a maximum flow rate of 4.5 GPM at 10 psi (0.7 bar). The pump is fully automatic, with a built-in inlet strainer, pressure switch, and check valve, and supplies smooth flow from trickle to full flow. Typical uses include applications where available water pressure is very low and fluctuates widely. Easy installation requires only that the water lines be connected, and the power cord plugged in.
Features:
Integrated pump and tank system
It can be mounted vertically or horizontally
Flow rates up to 4.5 US Gallons/min.
Kit Consists of:
115V Quad MPU, 4.5 GPM, SW 40, 0.77 gal capacity accumulator tank, plastic mounting board, and pump inlet strainer
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
572.14 |
|
|
Water Booster System - 40PSI - 4.5GPM - 24V
The Flojet 2840 Series Booster Systems are designed to provide constant water pressure of 0 to 40 psi (0.7 to 2.7 bar) and a maximum flow rate of 4.5 GPM at 10 psi (0.7 bar). The pump is fully automatic, with a built-in inlet strainer, pressure switch, and check valve, and supplies smooth flow from trickle to full flow. Typical uses include applications where available water pressure is very low and fluctuates widely. Easy installation requires only that the water lines be connected, and the power cord plugged in.
Features:
Integrated pump and tank system
It can be mounted vertically or horizontally
Flow rates up to 4.5 US Gallons/min.
Includes:
24V Quad MPU, 4.5 GPM, SW 40, 0.77 gal capacity accumulator tank, plastic mounting board, and pump inlet strainer
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
568.00 |
|
|
Flojet 02840-300 Water Sys 24V 4.5 gpm 40psi Sw
Flojet- Diaphragm Pump Water Booster System 24V, 4.5GPM, 40psi Switch, 1.1 Gallon Accumulator Tank
|
737.30 |
|
|
Water Booster System - 40 PSI - 4.5GPM - 12V
The Flojet 2840 Series Booster Systems are designed to provide constant water pressure of 0 to 40 psi (0.7 to 2.7 bar) and a maximum flow rate of 4.5 GPM at 10 psi (0.7 bar). The pump is fully automatic, with a built-in inlet strainer, pressure switch, and check valve, and supplies smooth flow from trickle to full flow. Typical uses include applications where available water pressure is very low and fluctuates widely. Easy installation requires only that the water lines be connected, and the power cord plugged in.
Features:
Integrated pump and tank system
It can be mounted vertically or horizontally
Flow rates up to 4.5 US Gallons/min.
Kit Consists of:
12V Quad MPU, 4.5 GPM, SW 40, 0.77 gal capacity accumulator tank, plastic mounting board, and pump inlet strainer
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
550.61 |
|
|
Flojet 02840-100 Water Sys 12V 4.5/40 Sw
Flojet- Diaphragm Pump Water Booster System 12V, 4.5GPM, 40psi Switch, 1.1 Gallon Accumulator Tank
|
714.74 |
|
|
Flojet 04100-113C Pump 12V 4.5gpm 40 Psi no Switch
Flojet Diaphragm Pump Quad 12V, 3/4” Hose Barb Snap-In Ports, Open Flow 5.0GPM, 40psi Max, Polypropylene, Buna Valves, Geolast Diaphragm, no Switch
|
172.28 |
|
|
Flojet 02840-000 M Water Sys 115V 4.5/40 Sw
Flojet- Diaphragm Pump Water Booster System 115V, 4.5GPM, 40psi Switch, 1.1 Gallon Accumulator Tank
|
742.68 |
|
|
Flojet 02840-000-Garden Hose Fitting Water Sys 115V 4.5/40 Sw
Flojet- Diaphragm Pump Water Booster System 115V, 4.5GPM, 40psi Switch, 1.1 Gallon Accumulator Tank, with Garden Hose Fittings
|
745.85 |
|
|
Flojet 02840-210 230V 3.5Gpm 40 psi Booster System
Flojet- Diaphragm Pump Water Booster System 230V, 3.5GPM, 40psi Switch, 1.1 Gallon Accumulator Tank
|
725.49 |
|
|
Flojet 04325-343 Pump 24V 4.5/40 Pse Sw
Flojet- Diaphragm Pump Quad 24V, 3/4” Hose Barb Snap-In Ports, 4.5GPM, 40psi Switch, Polypropylene, EPDM Valves, Santoprene Diaphragm, U.S.C.G. Approved, with Strainer
|
351.61 |
|
|
Flojet 04325-443 Pump 32V 4.5/40 Pse Sw
Flojet- Diaphragm Pump Quad 32V, 3/4” Hose Barb Snap-In Ports, 4.5GPM, 40psi Switch, Polypropylene, EPDM Valves, Santoprene Diaphragm, U.S.C.G. Approved, with Strainer
|
363.40 |
|
|
March Mag-Drive Centrifugal Pumps Bronze 115V High Speed 4.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
443.63 |
|
|
Flojet 04100-123 Pump 12V 4.5/40 Pvv Nsw
Flojet- Diaphragm Pump Quad 12V, Snap-In Ports, Open Flow 5.0GPM, 40psi Max, Polypropylene, Viton Valves, Viton Diaphragm, no Switch
|
293.24 |
|
|
Flojet G57-3208 Pump Aod Viton 3/8" Ports
Flojet Diaphragm Pump AOD Air Powered, 3/8" Hose Barb Snap-In Ports, 4.5GPM Max, Polypropylene, Viton Check Valve Seat and Diaphragm, 1/4” Hose Barb Straight Plastic Air Inlet
Capable of Air or CO2 drive pressures up to 100PSI (6.9bar)
Highest flow rate for any air pump of comparable size
Robust Design with durable integral mounting
Patented Shuttle Valve, eliminates stalling
Capable of passing solids up to 3.2mm diameter easily with large clog-free Check Valves
Corrosion Resistant materials capable of handling a wide range of chemicals
Sanitary design with insert molded diaphragm (Santroprene only)
Leak Resistant radial seals, no critical o-ring seals
Quiet Operation with large exhaust muffler
Ease of Installation with all quick disconnect ports
Stall-proof design with patented shuttle valve
Automotive Cleaning and Recycling;Chemical Transfer and dispensing;Bag-In-Box chemicals Parts Washers ;Car Wash Systems
Innovative compact design features a patented shuttle valve that eliminates stalling and provides a long life. Features a chemically resistant polypropylene body with a choice of EP/PP blend, FKM or FFKM elastomers, as well as quick disconnect liquid and gas port fittings for easy installation.
|
315.84 |
|
|
Flojet 04100-113A Pump 12V 4.5/40 Pgb N/Sw
The Flojet 4100-113 has an open flow rate of 4.5 GPM and is fitted with Buna checkvalves and geolast diaphragms.
The Flojet 4100 series is a self-priming pump.
It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).
For vertical pump mounting be sure that the motor is located on top. This will prevent water from entering the motor chamber in event of a leak.
Compact design and plug-in port fitting make installation easy.
Can run dry without damage and handle liquids up to 54° C.
No metal contact with liquid being pumped.
Ball bearing drive throughout pump and motor assures longer pump life.
Excellent self-priming capability. Pump may be located above the liquid level.
Powerful, permanent magnet motor with low current draw and long life brushes.
|
245.25 |
|