Connect Charge Inlet Product Features For use with the Guest Connect Charge plug Exclusive molded notch on plug locks into inlet, eliminates rewiring Mounts from the rear using locking ring or from the front with 3 screws Low profile cap won't catch fishing line Can be mounted almost anywhere on a boat Mounts easily to fiberglass and aluminum hulls Black WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

On-Board Charger Inlet Great for Bass Boats! The Marinco On-Board Charger Inlet makes battery charging through an on-board battery charger safer and more convenient. The inlet mounts on the boat's exterior and is hard wired directly to the charger. Just open the flip lid cover and plug an extension cord into the inlet to bring charging power to the boat's batteries. All of the hatches remain closed and locked throughout the charging cycle, adding convenience and security for the boater. Features: 15Amp 125V straight blade inlet Low profile cap won't catch fishing line Mounts easily to fiberglass and aluminum hulls Perma-Lock™ terminals and color coded wire entrance holes make wiring a snap UV resistant housing/cap Color: Black WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

15A 125V On-Board Charger Inlet - Front Mount - White Marinco on-board charger inlets make battery charging through an on-board battery charger safer and more convenient. Inlets mount on the boat exterior and are hard-wired directly to the charger. To use, just open the flip lid cover and plug an extension cord into the inlet. All hatches remain closed and locked throughout the charging cycle for added security. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

100A Connector for Inlet - 120/208V  Mate with M5100B9R inlet.  WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ConnectPro® Charging/Trolling Receptable, Plug & 6-Guage Adapter The ConnectPro® system features locking plug and receptacle and spring clamping connection, which provide a secure electrical contact. Receptacle is universal design for 2-or-3 wire configuration, 12, 24, 12//24, 24//36 or 36 volt systems. Features: Watertight sealing cap Corrosion resistant, plated brass electrical components with drain holes in receptacle to keep water away from electrical components Standard 1-1/8 diameter mounting hole and accepts up to 8 gauge wire Includes mounting plate Plug has O-ring seal for waterproof connections Weather resitant plug cover Accepts 16 to 8 gauge wire WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ConnectPro® Charging/Trolling System Receptacle & Plug ConnectPro® Receptacle Universal design for 2 or 3-wire configuration 12, 24, 12/24, 24/36 or 36 volt systems Watertight sealing cap Corrosion resistant, plated brass electrical components Drain holes in receptacle keep water away from electrical components Perma-Lock™ screw terminals will not loosen under extreme hull vibration Standard 1-1/8" diameter mounting hole Easy to install, with supplied mounting plate for front panel installation, or locking ring for rear access installation Accepts 10 and 8 gauge wire Easily replaces other trolling motor plugs and receptacles ConnectPro® Plug O-ring seal for waterproof connections Weather resistant plug cover Corrosion resistant, plated brass electrical components Accepts 16 to 8 gauge wire Ergonomic contoured grip for easy hook-up and ground blade alignment WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

By now, the skipper in your life has probably dropped a few hints about holiday gifts. Was it the note left on the coffee pot about Articulated ABS Barrel Hinge foldable Aluminum Tubing? At first glance, one would have thought that the message was a reminder about being out of coffee filters. Then it comes back to you that there was a conversation in the car about GemLock Assembled Folding Struts.    Foldable aluminum tubing is one of the hottest trends in stainless steel hardware for marine canvas and solar panel frames. The tubing offers versatility in styling, high quality, and ease of use. https://www.clrmarine.com/462m4/manufacturers/g/gemini-marine.html   Back to your captain's holiday gift list. Was there a subtle hint, while you both were swimming off the boat, and your skipper showed concern that the transom ladder seemed a little short by a few steps? She would find getting out of the lake sooooo much easier if she didn't have to reach her foot up so far to the lowest step. She had also mentioned a discussion with other boat captains about the Extend Your Step, an easy-to-use boat boarding ladder extension. Several of her sailing buddies already have them and raved about the ease and portability. .   All of the products mentioned above are available at CLR Marine.com. How confident are the folks at CLR Marine about the Extend Your Step regarding ease in boarding and extending the ladder length? This product reflects the confidence and integrity of CLR Marine's owner, Chuck Reed. He invented the Extend Your Step! When shopping for the extending ladder, be sure to check out the Extend Your Step Three – a longer and non-moving version of the Extend Your Step! https://www.clrmarine.com/Boat-Boarding-Ladder-Extension   It's possibly time for your captain to give the best seat in the house – on your boat- an upgrade. There is no better place to watch the glint of the sun on the waves than in a stern perch seat. Stern rail seats are now available for older model boats, even pre-1993, and the seats are removable. https://www.clrmarine.com/sternperch-seats.html     Stocking Stuffers   Floatable key rings. If you are old enough to have keys, then you are old enough to lose keys. House keys, boat keys, car keys – when these fall into the drink and aren't retrievable, your boat outing takes a turn for the worse. Car key fobs are expensive to replace. Neon colored strong straps or carabiner clips offer added security against key loss. DryCASE Smartphone Case   The DryCASE waterproof cell phone case keeps your electronics protected, whether surfing, paddle boarding, or canoeing. The DryCASE uses vacuum seal technology to ensure a watertight seal every time. Best of all, you'll still be able to use your touch screen to text or make calls, and the crystal clear covering makes taking pictures a cinch. When you purchase the DryCASE you will also receive a small hand pump, neoprene armband, and a lanyard  $36.92. https://www.clrmarine.com/m4/45443—drycase-smartphone-case.html   RAM Mount AQUA BOX Medium RAM AQUA BOX® cases provide sealed enclosure and protection for your handheld devices. The clear, touch through screen allows you to view your electronics and use their function keys while in place. There is even a place for a small lock to serve as a theft deterrent. The AMPS hole pattern on the back of the box allows this enclosure to be attached to many RAM mounting bases and kits. Ideally suited to Motorcycles and ATV's, the AQUA BOX keeps your portable devices safe, dry, and accessible $36.49.   Scotty 130 Paddle Safety Leash   Paddles, rods, nets, gaffs, and many other items can be secured while in use with the Scotty Safety Leash. Features include two extra strong Scotty 1009 swivel snaps; super-strong Flex Coil cord allows for maximum unrestricted movement and stretches to approx. 6'. Unit Includes two figure eight securing straps $11.99. https://www.clrmarine.com/m4/37811--scotty-130-paddle-safety-leash-black.html Gifts under $30.00   Don't forget about covers for your water toys. The Dallas Manufacturing Co – Pedal Boat Cover will keep your pedal boat dry, dirt free, and protected from the sun when not in use. Features include 150 Denier Silver Polyester, fits both 3 and 5 Person Pedal Boats and is backed by a one year warranty $13.19.  https://www.clrmarine.com/m4/36879—dallas-manufacturing-co-pedal-boat-polyester-cover.html   Mustang Lil' Legends 70 Youth Vest -  Fluorescent Yellow-Green/Gray   Have guests arrived on your boat with a small young family member who needs a life vest? The Mustang Lil's Legends is a quality youth vest, and it never hurts to have a spare on board. It fits a child 50-90 pounds  $21.59.  https://www.clrmarine.com/m4/49897—mustang-lil-legends-70-youth-vest-50-90lbs-fluorescent-yellow-green-gray.html     Be good—Santa's watching. Stay healthy. Fair Winds. Smooth sailing.   To obtain more information about the products and services mentioned in this article, please contact CLR Marine https://www.clrmarine.com ______________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com     

Flip Pro with Front Fit Bezel 12/24V Fast Charge Dual USB-A/C Socket Ultra-fast USB charging for the next-generation boater.  Flip Pro is designed for use with either a 12V or 24V input and features a 1x USB-A and 1x USB-C charging port. This provides the optimum choice of connection and the fastest charging for your device onboard. Ultra-fast USB charging for the next-generation boater.  Flip Pro with a front bezel is designed for use with either a 12V or 24V input and features a 1x USB-A and 1x USB-C charging port. This provides the optimum choice of connection for any device and the fastest charging for your device onboard. Flip Pro with front bezel was manufactured as an adaption to the original SC-USB-F1 to offer flexibility to installation, as in some cases, it is not possible to gain access to behind panels. Therefore, the front fit bezel provides an alternative route for installation, allowing the option to fit the product from the front using screws. When not in use, the spring-loaded cap remains tightly closed, protecting the ports from the elements. When charging, it quickly locks open to protect your cables when plugged in. Featuring a super compact footprint, Flip Pro is constructed from premium, marine-grade materials. and is IPX4 waterproof, making it completely washdown-ready. Flip Pro is FAST! It will charge at 36W on a 12V system or up to 60W on a 24V system. This makes it perfect for charging modern laptops via the USB-C port. It’s also 2x faster for charging large tablets and is designed to effortlessly charge both an iPad Pro & iPhone at the same time.  The install cut-out matches those of standard USB sockets for easy retrofit or swap of an existing USB charger, allowing you to keep up with the heavier power draws of modern electronic devices. Universal: Universal fit for any USB-A or USB-C connectors. Fast charge (60W max) up to 2 devices at a time. Easy Install, using standard USB mounting hole - 29mm (1 1/8”) Washdown Proof: IPX4 waterproof with the cover closed. Marine Ready: Internal anti-corrosion protective coating UV resistant 316 stainless hinge and spring Electrical Information: Input voltage: 10-30V DC (12/24V System) Input current Max: 6A (10A fuse recommended)  Standby power draw: 0.01W USB – C output:  60W max on 24V system 36W max on 12V system USB – A output:  36W max The charge cable supplied with your device (tablet, phone, action camera, etc) must be used to achieve maximum charge performance from this charger. Phones will charge at the same speed whether on a 12V or 24V input voltage system. However, a 24V system must be used to get the full 60W output suitable for fast-charging laptops.  What is USB-C?  More powerful - Our USB-C has no problems charging even the largest iPad Pro at twice the speed as a USB-A.  More Compact: The slim, oval shape is smaller than USB-A and is also symmetrical and reversible - no more having to flip the cable over to get it into the port! More Flexible: It’s fast becoming the universal connector/charge type on all devices, replacing the USB-A, USB-B, and Micro-USB. New devices are being launched with this charge option only e.g. iPhone 13.

Skylla-i Battery Charger 24/100 (3) 230V Battery Charger The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current. Features: Rugged - Aluminium epoxy powder-coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity, and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Flexible - Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Please refer to the manual for a complete overview of the possibilities.  Synchronized parallel operation - Several chargers can be synchronized with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP cables. Note: Two output and three output chargers cannot be paralleled with each other. Please see the manual for details. The right amount of charge for a lead-acid battery: variable absorption time - When only shallow discharges occur the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. Preventing damage due to excessive gassing: BatterySafe mode - If to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached. Less maintenance and aging when the battery is not in use: Storage mode - The storage mode kicks in whenever the battery has not been subjected to discharge for 24 hours. In the storage mode float voltage is reduced to 2.2V/cell (26.4V for 24V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure. To increase battery life: temperature compensation - Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead-acid batteries and/or when important fluctuations in battery temperature are expected. Battery voltage sense - To compensate for voltage loss due to cable resistance, the Skylla-i is provided with a voltage sense facility so that the battery always receives the correct charge voltage. Suitable for AC and DC supply (AC-DC and DC-DC operation) - The chargers also accept a DC supply. Use as a power supply - As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available. Li-Ion (LiFePO4) ready - Simple charger on-off control can be implemented by connecting a relay or open collector optocoupler output from a Li-Ion BMS to the remote control port of the charger. Alternatively, complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port. Specifications: Input voltage (VAC): 230V Input voltage range (VAC): 185-265V Input voltage range (VDC): 180-350V Maximum AC input current @ 180 VAC: 20A Frequency (Hz): 45-65Hz Charge voltage 'absorption' (VDC): 28.8V Charge voltage 'float' (VDC): 27.6V Charge voltage ‘storage’ (VDC): 26.4V Charge current (A): 3 x 100A (max total output: 100A) Charge algorithm: 7-stage adaptive Battery capacity: 500-1000Ah Charge algorithm (LiFePO4): 3 stages, with on-off control or CAN bus control Temperature sensor: Yes Power supply mode: Yes Remote on-off port: Yes (can be connected to a Li-Ion BMS) VE.Can communication port: Two RJ45 connectors, NMEA2000 protocol, galvanically isolated. Integrated 12V CAN-bus power supply, 30V DC maximum Synchronized parallel operation: Yes, with VE.Can Forced cooling: Yes Protection: Battery reverse polarity (fuse) / Output short circuit / Over temperature Operating temp. range: -20 to 60°C (Full output current up to 40°C) Material & Colour: aluminium (blue RAL 5012) Battery connection: M8 bolts 230 VAC-connection: screw-clamp 10mm² (AWG 7) Protection category: IP21 Weight: 16 lbs. (7 kg) Dimensions (hxwxd): 405 x 250 x 150 in (16.0 x 9.9 x 5.9mm) Please contact your dealer for any returns, repairs or support issues related to this product.

Skylla - 24/100 TG Charger - 230V One full rated output and one (1) 4 Amp output.  Charge voltage can be precisely adjusted to suit any battery system.   The input for the charger is 230V at 50/60HZ.  Charge voltage can be measured directly on the battery terminals in order to compensate for voltage loss due to cable resistance.  An external sensor allows to measure battery temperature and compensate charge voltage accordingly. Features: Perfect chargers for any type of battery - Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system.  In particular, sealed maintenance-free batteries must be charged correctly in order to ensure long service life.  Overvoltage will result in excessive gassing and venting of a sealed battery.  The battery will dry out and fail. Suitable for AC and DC supply (AC-DC and DC-DC operation) Every TG Charger has a microprocessor, which accurately controls the charging in three steps Use of TG Chargers as power supply - As a result of the perfectly stabilized output voltage, a TG Charger can be used as a power supply if batteries or large buffer capacitors are not available. Manufactured with a battery temperature sensor.  When connected, charge voltage will automatically decrease with increasing battery temperature.  In order to compensate for voltage loss due to cable resistance, TG Chargers are provided with a voltage sensor so that the battery always receives the correct charge voltage Technical Specifications:  Input Voltage - 230V AC Input Voltage Range - 185 to 264V AC Input Voltage Range - 180 to 400V DC Battery Capacity - 500 to 1000 Ah  Frequency - 45 to 65 Hz Battery Connection - M8 studs 230V AC Connection - Screw clamp (AWG 6) Dimensions (H x W x D) - 14.4" x 9.9" 10.1" (36.5 x 25 x 25.7 cm) Weight - 22 Lbs (10 kg) In the Box: Charger Mounting brackets Temperature sensor with 4.9' (1.5 M) wire Instruction manual  *Sold as an Individual  Please contact your dealer for any returns, repairs or support issues related to this product.

ROKK SC-USB-02 Charge+  Waterproof USB Socket - Dual Port The ultimate rapid charge waterproof USB charger with dual socket connectivity that can charge devices up to 3x faster than standard USB sockets.  Featuring an ultra low profile, that’s perfect for any outdoor application. *Cables sold separately   Features: Works with any USB Type-A Connector Charge up to 2 devices at a time Anti-corrosion coating on circuit board UV resistant 316 stainless hinge and spring Low profile, small footprint Technical Specifications: USB Input Voltage Range - 12-24V  USB Output Voltage - 5V +/- 5%  Output Current - 4.2A IPX6 Waterproof with the cover closed Protection - UV Resistant In the Box: USB Socket Instruction manual *Sold as an Individual

RV Kit 30 AMP Dual Configuration Cordset and Stainless Steel Inlet Combo - 30' People discovering the joys of RVing are often unaware of the dangers lurking in their outdated, Twist-type park power connections.  Today's RVs have enormous electrical draws. Microwaves, TVs, in-floor heating and slide-out systems are conveniences that weren't even invented when the L-style pin system was introduced in the 1930s. These Pigtail Adapters have an asymmetrical design with locking, multi-point stainless steel side clips for simple one-handed operation.  These Pigtail Adapters are designed for extreme weather conditions.  The 30 AMP 125 V RV cordset provides a weather resistant power cord solution for park power. The cordset comes with the SmartPlug connector for the RV side and the industry standard three pin connector for the park power side.  It comes standard with a cool blue LED Power indicator on the female connector, a special coating that makes it more flexible and easy to roll up. Features: Eliminates Overheating – Increased pin and clip surface area greatly improves electrical conductivity during high amperage demand. Ease of Use – No twist required, the unique plug body shape and push-in design means it only goes in the right way every time – even in the dark. Multi-Point Locking System – Side clips and inlet cover lock the plug body securely into the inlet which eliminates any stress on the electrical components by movement of the power cord. Weather Resistant Seals – Multi-fin silicone gaskets installed in the plug body eliminate any water penetration when plug is connected to inlet. Quick and Easy Installation – Inlet mounting flange holes match existing inlet holes for an installation that is typically finished in 30 minutes. Technical Specifications: Length - 30' Cordeset Color - Black Inlet Color - Stainless Steel Vehicle Side Connection - 30 AMP/125 V SmartPlug Park Side Connection - 30 AMP/125 V Push Type Plug In the Box: 30' Cordset Inlet cover Instruction manual *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RV Kit 30 AMP Dual Configuration Cordset and White Inlet Combo - 30' People discovering the joys of RVing are often unaware of the dangers lurking in their outdated, Twist-type park power connections.  Today's RVs have enormous electrical draws. Microwaves, TVs, in-floor heating and slide-out systems are conveniences that weren't even invented when the L-style pin system was introduced in the 1930s. These Pigtail Adapters have an asymmetrical design with locking, multi-point stainless steel side clips for simple one-handed operation.  These Pigtail Adapters are designed for extreme weather conditions.  The 30 AMP 125 V RV cordset provides a weather resistant power cord solution for park power. The cordset comes with the SmartPlug connector for the RV side and the industry standard three pin connector for the park power side.  It comes standard with a cool blue LED Power indicator on the female connector, a special coating that makes it more flexible and easy to roll up. Features: Eliminates Overheating – Increased pin and clip surface area greatly improves electrical conductivity during high amperage demand. Ease of Use – No twist required, the unique plug body shape and push-in design means it only goes in the right way every time – even in the dark. Multi-Point Locking System – Side clips and inlet cover lock the plug body securely into the inlet which eliminates any stress on the electrical components by movement of the power cord. Weather Resistant Seals – Multi-fin silicone gaskets installed in the plug body eliminate any water penetration when plug is connected to inlet. Quick and Easy Installation – Inlet mounting flange holes match existing inlet holes for an installation that is typically finished in 30 minutes. Technical Specifications: Length - 30' Cordeset Color - Black Inlet Color - White Vehicle Side Connection - 30 AMP/125 V SmartPlug Park Side Connection - 30 AMP/125 V Push Type Plug In the Box: 30' Cordset Inlet cover Instruction manual *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RV Kit 30 AMP Dual Configuration Cordset and Grey Inlet Combo - 30' People discovering the joys of RVing are often unaware of the dangers lurking in their outdated, Twist-type park power connections.  Today's RVs have enormous electrical draws. Microwaves, TVs, in-floor heating and slide-out systems are conveniences that weren't even invented when the L-style pin system was introduced in the 1930s. These Pigtail Adapters have an asymmetrical design with locking, multi-point stainless steel side clips for simple one-handed operation.  These Pigtail Adapters are designed for extreme weather conditions.  The 30 AMP 125 V RV cordset provides a weather resistant power cord solution for park power. The cordset comes with the SmartPlug connector for the RV side and the industry standard three pin connector for the park power side.  It comes standard with a cool blue LED Power indicator on the female connector, a special coating that makes it more flexible and easy to roll up. Features: Eliminates Overheating – Increased pin and clip surface area greatly improves electrical conductivity during high amperage demand. Ease of Use – No twist required, the unique plug body shape and push-in design means it only goes in the right way every time – even in the dark. Multi-Point Locking System – Side clips and inlet cover lock the plug body securely into the inlet which eliminates any stress on the electrical components by movement of the power cord. Weather Resistant Seals – Multi-fin silicone gaskets installed in the plug body eliminate any water penetration when plug is connected to inlet. Quick and Easy Installation – Inlet mounting flange holes match existing inlet holes for an installation that is typically finished in 30 minutes. Technical Specifications: Length - 30' Cordeset Color - Black Inlet Color - Grey Vehicle Side Connection - 30 AMP/125 V SmartPlug Park Side Connection - 30 AMP/125 V Push Type Plug In the Box: 30' Cordset Inlet cover Instruction manual *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RV Kit 30 AMP Dual Configuration Cordset and Black Inlet Combo - 30' People discovering the joys of RVing are often unaware of the dangers lurking in their outdated, Twist-type park power connections.  Today's RVs have enormous electrical draws. Microwaves, TVs, in-floor heating and slide-out systems are conveniences that weren't even invented when the L-style pin system was introduced in the 1930s. These Pigtail Adapters have an asymmetrical design with locking, multi-point stainless steel side clips for simple one-handed operation.  These Pigtail Adapters are designed for extreme weather conditions.  The 30 AMP 125 V RV cordset provides a weather resistant power cord solution for park power. The cordset comes with the SmartPlug connector for the RV side and the industry standard three pin connector for the park power side.  It comes standard with a cool blue LED Power indicator on the female connector, a special coating that makes it more flexible and easy to roll up. Features: Eliminates Overheating – Increased pin and clip surface area greatly improves electrical conductivity during high amperage demand. Ease of Use – No twist required, the unique plug body shape and push-in design means it only goes in the right way every time – even in the dark. Multi-Point Locking System – Side clips and inlet cover lock the plug body securely into the inlet which eliminates any stress on the electrical components by movement of the power cord. Weather Resistant Seals – Multi-fin silicone gaskets installed in the plug body eliminate any water penetration when plug is connected to inlet. Quick and Easy Installation – Inlet mounting flange holes match existing inlet holes for an installation that is typically finished in 30 minutes. Technical Specifications: Length - 30' Cordeset Color - Black Inlet Color - Black Vehicle Side Connection - 30 AMP/125 V SmartPlug Park Side Connection - 30 AMP/125 V Push Type Plug In the Box: 30' Cordset Inlet cover Instruction manual *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.