MP Pumps 21149 GASKET

MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 15 Part #: MP21381 Size: 3 in. NPT Flow-Rate: 320 GPM Head Feet: 145   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

MP Pumps 21383 FM 15 BRONZE PUMP MP Pumps 21383, FLOMAX 15 Self Priming Centrifugal Pump, Wet End Only FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators and Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   3" X 3" NPT Ports Capacity up to 320 GPM Total Head up to 145 feet Bronze construction 5.75 inch diameter impeller

MP Pumps 21312, FLOMAX 5 Self Priming Centrifugal Pump 1-1/2" X 1-1/2" NPT Ports, Capacity up to 145 GPM, Total Head up to 100 feet.   FM5PMP C: PED 5.0   MP Pumps Flomax 5, 1-1/2" pedestal mount self priming cast iron pump # 21312. MP Pumps Flomax 5, rated at 100 GPM in cast iron construction with viton mechanical seal.   Specifications   Rated Capacity 100 GPM Maximum Discharge Pressure: 40 PSI Suction & Discharge Connections: 1-1/2" X 1-1/2" FNPT Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve, 304 stainless steel stub shaft to fit 5/8"; viton mechanical seal.   Features:   Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift 5 blade impeller available for higher flows Base plate shown above is optional Double seal available for dry run applications Hydraulic motor .22 cu. in. Hydraulic motor .37 cu. in. Hydraulic motor .45 cu. in. Stainless steel impeller

MP Pumps 21338 PUMP FM8 BRZ PED MNT   MP Pumps Flomax 8, 2" NPT self priming centrifugal pumps # 21338. Up to 140 GPM, up to 40 PSI (92'), 3450 RPM, all bronze construction. Removable flanges and replaceable wear plates protect the housing and eliminate wear. All fasteners are Stainless Steel. Standard mechanical seal have Viton elastomers.   Specifications Rated Capacity 140 GPM Maximum Discharge Head 92 feet (40 PSI) Suction & Discharge Connections 2" X 2" FNPT   Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight 49 lbs. 304 stainless steel stub shaft viton mechanical seal.    

MP Pumps 21366 PUMP FM10 C/I 184TC MT Flomax 10 Pumpaks are liquid-ends less power source. Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Cast iron construction and will fit 184C/145TC NEMA motors with feet. PumPaks are provided less motors and with 5" maximum impeller diameters.   Specifications Rated Capacity 140 GPM Maximum Head: 92 feet (40 PSI) Suction & Discharge Connections: 2" X 2" FNPT Impeller Diameter: Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft to fit either 5/8" or 7/8" driver shaft; viton mechanical seal.   Pump water end only less motors. Motors Required: 1-1/2 HP, 2 HP or 3 HP TEFC, 3450 rpm, single phase or three phase, 60 Hz Motor Frames Required: 184C/145TC NEMA motors with feet.

MP Pumps 36067 PUMP HHLF HR 2" GAS/DIESEL MP Pumps 36067, HHLF High Head Low Flow Self Priming Centrifugal Pump End Only, 1-1/2" or 2" x 1-1/2" or 2"   High Pressure USCG Secifications Auxilary Fire Control HHLF2.0PPK B: ENG 1.0 6.7 HR

Sierra gaskets for Mercury outboard water pumps and impellers.

Sierra gaskets for Mercury outboard water pumps and impellers.

Sierra gaskets for Mercury outboard water pumps and impellers.

MP Pump 23241 Pump Series 110 Ci Gas Eng MP Pumps 23241 Series 110 End Suction Centrifugal Pump Cast The SERIES 110 high volume centrifugal pumps are close-coupled to standard NEMA "C" face motors. Open adaptor protects motor. All models are available in cast iron, bronze or aluminum construction to suit a wide variety of liquids. All fasteners are stainless steel to reduce corrosion. Impellers are balanced to improve efficiency and bearing life. Standard carbon / ceramic / Viton mechanical seal is self-adjusting and corrosion resistant to handle almost any liquid.

MP Pump 24550 Pump Fm8 Brz Man Clutch MP Pumps 24550 FLOMAX8 2" x 2" Self-Priming Centrifugal Pump, Bronze, Pedestal/Clutch, 5" Impeller Renewable wear plate. Stainless steel drive sleeve. Stainless steel closure. Up to a 25 foot suction lift Specifications for this product maximum flow150 gallons_per_minute Included ComponentsCentrifugal Pump UNSPSC Code40151500 MaterialBronze body materialBronze brand nameMP Pumps Number of articles1 Model number24550 part number24550

Sierra gaskets for Mercury outboard water pumps and impellers.

FLOMAX®8 by MP Pump part 26079 2" x 2" Self Priming Centrifugal Pump   FLOMAX® 8 self-priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump’s built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX® 8 PumPAK® is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive.   Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wearplate, and a semi-open dynamically balanced impeller.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.

MP Pumps 22925 PUMP HOUSING