|
115-24-10 Power Supply
This super-rugged DC power supply is ideal for powering 24-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.
Features:
Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
Thermally activated cooling fan on “CD” units
Specifications:
Nominal Input/VAC: 115/230
Maximum Input Current @115: 5.5
Maximum Input Current @230: 2.5
Output Amperage (Intermittent): 10
Output Amperage (Continuous): 4
Weight: 20 lbs. / 9.1 kg
Case Size:
H x W x D (inch): 5.7” x 4.8” x 16.3”
Input Range
105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC
Operating Temperature
Standard Units - 0-50 degrees C, Derate linearly from 100% @ 40 degrees C to 50% @ 50 degrees C thermal shutdown @ 85 degrees C case temperature
Duty Cycle:
Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 hours/day 100% Duty
Options:
Modify for use as a battery charger
The output voltage is adjusted (see Output Voltage for range)
Transfer relay for back-up battery in event of power failure (ERC option)
Output Voltage:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P (@ 110-125 / 220-250 VAC input)
1% Line and Load (@ 110-125 / 220-250 VAC input)
Mechanical:
Powder-coated aluminum heat sink case
Front panel terminal block
Heavy-duty mounting flange
Conformal-coated PC board
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1053.23 |
|
|
115-24-18CD Power Supply
This super-rugged DC power supply is ideal for powering 24-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.
Features:
Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
Thermally activated cooling fan on “CD” units
Specifications:
Nominal Input/VAC: 115/230
Maximum Input Current @115: 5.5
Maximum Input Current @230: 2.5
Output Amperage (Intermittent): 10
Output Amperage (Continuous): 4
Weight: 20 lbs. / 9.1 kg
Case Size:
H x W x D (inch): 5.7” x 4.8” x 16.3”
Input Range
105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC
Operating Temperature
C.D. Units - 0-65 degrees C, Derate linearly from 100% @ 50 degrees C to 50% @ 65 degrees C thermal Shutdown @ 85 degrees C case temperature
Duty Cycle:
Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 hours/day 100% Duty
Options:
Modify for use as a battery charger
The output voltage is adjusted (see Output Voltage for range)
Transfer relay for back-up battery in event of power failure (ERC option)
Output Voltage:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P (@ 110-125 / 220-250 VAC input)
1% Line and Load (@ 110-125 / 220-250 VAC input)
Mechanical:
Powder-coated aluminum heat sink case
Front panel terminal block
Heavy-duty mounting flange
Conformal-coated PC board
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1650.23 |
|
|
115-24-35CD Power Supply
This super-rugged DC power supply is ideal for powering 24-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.
Features:
Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
Thermally activated cooling fan on “CD” units
Specifications:
Nominal Input/VAC: 115/230
Maximum Input Current @115: 5.5
Maximum Input Current @230: 2.5
Output Amperage (Intermittent): 10
Output Amperage (Continuous): 4
Weight: 20 lbs. / 9.1 kg
Case Size:
H x W x D (inch): 5.7” x 4.8” x 16.3”
Input Range
105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC
Operating Temperature
C.D. Units - 0-65 degrees C, Derate linearly from 100% @ 50 degrees C to 50% @ 65 degrees C thermal Shutdown @ 85 degrees C case temperature
Duty Cycle:
Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 hours/day 100% Duty
Options:
Modify for use as a battery charger
The output voltage is adjusted (see Output Voltage for range)
Transfer relay for back-up battery in event of power failure (ERC option)
Output Voltage:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P (@ 110-125 / 220-250 VAC input)
1% Line and Load (@ 110-125 / 220-250 VAC input)
Mechanical:
Powder-coated aluminum heat sink case
Front panel terminal block
Heavy-duty mounting flange
Conformal-coated PC board
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2331.34 |
|
|
115-12-20A Power Supply
This super-rugged DC power supply is ideal for powering 12-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.
Features:
Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
Thermally activated cooling fan on “CD” units
Specifications:
Nominal Input/VAC: 115/230
Maximum Input Current @115: 5.5
Maximum Input Current @230: 2.5
Output Amperage (Intermittent): 20
Output Amperage (Continuous): 8
Weight: 20 lbs. / 9.1 kg
Case Size:
H x W x D (inch): 5.7” x 4.8” x 16.3”
Input Range
105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC
Operating Temperature
Standard Units - 0-50 degrees C, Derate linearly from 100% @ 40 degrees C to 50% @ 50 degrees C thermal shutdown @ 85 degrees C case temperature
Duty Cycle:
Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 hours/day 100% Duty
Options:
Modify for use as a battery charger
The output voltage is adjusted (see Output Voltage for range)
Transfer relay for back-up battery in event of power failure (ERC option)
Output Voltage:
13.6 VDC (internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P (@ 110-125 / 220-250 VAC input)
1% Line and Load (@ 110-125 / 220-250 VAC input)
Mechanical:
Powder-coated aluminum heat sink case
Front panel terminal block
Heavy-duty mounting flange
Conformal-coated PC board
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1060.00 |
|
|
115-12-35CD Power Supply
This super-rugged DC power supply is ideal for powering 12-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.
Features:
Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
Thermally activated cooling fan on “CD” units
Specifications:
Nominal Input/VAC: 115/230
Maximum Input Current @115: 7.5
Maximum Input Current @230: 3.5
Output Amperage (Intermittent): 35
Output Amperage (Continuous): 35
Weight: 32 lbs. / 14.6 kg
Case Size:
H x W x D (inch): 6.5” x 9.5” x 14.0”
Input Range
105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC
Operating Temperature
C.D. Units - 0-65 degrees C, Derate linearly from 100% @ 50 degrees C to 50% @ 65 degrees C thermal Shutdown @ 85 degrees C case temperature
Duty Cycle:
Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 hours/day 100% Duty
Options:
Modify for use as a battery charger
The output voltage is adjusted (see Output Voltage for range)
Transfer relay for back-up battery in event of power failure (ERC option)
Output Voltage:
13.6 VDC (internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P (@ 110-125 / 220-250 VAC input)
1% Line and Load (@ 110-125 / 220-250 VAC input)
Mechanical:
Powder-coated aluminum heat sink case
Front panel terminal block
Heavy-duty mounting flange
Conformal-coated PC board
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1550.04 |
|
|
115-12-8 Power Supply
This super-rugged DC power supply is ideal for powering 12-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.
Features:
Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
Thermally activated cooling fan on “CD” units
Specifications:
Nominal Input/VAC: 115/230
Maximum Input Current @115: 2.5
Maximum Input Current @230: 1.5
Output Amperage (Intermittent): 8
Output Amperage (Continuous): 5
Weight: 32 lbs. / 14.6 kg
Case Size:
H x W x D (inch): 6.0” x 4.6” x 8.5”
Input Range
105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC
Operating Temperature
Standard Units - 0-50 degrees C, Derate linearly from 100% @ 40 degrees C to 50% @ 50 degrees C thermal shutdown @ 85 degrees C case temperature
Duty Cycle:
Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 hours/day 100% Duty
Options:
Modify for use as a battery charger
The output voltage is adjusted (see Output Voltage for range)
Transfer relay for back-up battery in event of power failure (ERC option)
Output Voltage:
13.6 VDC (internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P (@ 110-125 / 220-250 VAC input)
1% Line and Load (@ 110-125 / 220-250 VAC input)
Mechanical:
Powder-coated aluminum heat sink case
Front panel terminal block
Heavy-duty mounting flange
Conformal-coated PC board
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
485.99 |
|
|
Galley Maid MR-24-10 Rebuilt Pump and Motor
Galley Maid water pressure system MR Series pump.
GPM Max:10
Voltage: 24 Volts
Breaker Size:30 amp
Inlet: 1" NPT
Outlet: 3/4" NPT
Rebuilt units also requiry a Core Fee, add the suggested product below to your cart or order will be canceled.
Use Discount Code: CORECHARGE when checking out.
|
698.40 |
|
|
PT-24-45U Battery Charger
“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.
A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.
Features:
24-volt model
“Smart” circuitry provides three-stage charging – bulk, absorption, float
Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages
Multiple isolated output banks; ammeter indicates total output current
The optional sensor adjusts output voltage based on battery temperature
Current limiting prevents damage from overloading
Use as a power supply; can power loads without a battery in line
Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry
Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield
Install in conjunction with PT-MCU for additional control and monitoring
ABS-type approval for battery charging and power supplies
Specifications:
Input VAC (50-60 Hz.): 90 – 264
Input Amps @ Full Load: @ 115 VAC: 12, @ 230 VAC: 7
Power Factor: .98@115V and .95@230V
Max Output Amps: 45
Output Banks: 3
Battery Capacity (Amp-Hours): 90 – 450
Operating Temp. Rating Reference: T-5
Case Size Reference: A-4
Case Size (H x W x D): 14.8B x 9.6 x 5.6D inches (37.6D x 24.4 x 14.2D centimeters) *Note with Dripshield installed D add 1” (2.54 cm) to height and .5” (1.2 cm) to depth
Weight Lbs./Kg: 12/6
Optional Temp. Sensor Model: TCS-12/24
Remote Panel Model: RP
Compliance Reference: EN, CE, ABS
Temperature Rating References:
Temperature: -20 degrees C to +70 degrees C
Derate Linearly From 100% @ 50 degrees C to 50% @ 70 degrees C
Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation):
Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load
Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load
Compliance References:
UL: UL 1950 (per DNB report)
CG: USCG CFR 183.410 (Ignition protected)
EN: EN 60335-1
CE: Carries the CE mark
ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13.
Options:
Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1827.58 |
|
|
PT-24-8W Battery Charger
“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.
A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.
Features:
24-volt model
“Smart” circuitry provides three-stage charging – bulk, absorption, float
Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages
Multiple isolated output banks; ammeter indicates total output current
The optional sensor adjusts output voltage based on battery temperature
Current limiting prevents damage from overloading
Use as a power supply; can power loads without a battery in line
Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry
Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield
Install in conjunction with PT-MCU for additional control and monitoring
ABS-type approval for battery charging and power supplies
Specifications:
Input VAC (50-60 Hz.): 85 – 264
Input Amps @ Full Load: @ 115 VAC: 2.8, @ 230 VAC: 1.4
Power Factor: .98@115V and .93@230V
Max Output Amps: 8
Output Banks: 3
Battery Capacity (Amp-Hours): 16 – 80
Operating Temp. Rating Reference: T-1
Case Size Reference: A-1
Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (28.4A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth
Weight Lbs./Kg: 8/4
Optional Temp. Sensor Model: TCS-12/24
Remote Panel Model: RP
Compliance Reference: CG, CE, ABS
Temperature Rating References:
Temperature: -10 degrees C to +60 degrees C
Derate Linearly From 100% @ 40 degrees C to 60% @ 60 degrees C
Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation):
Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load
Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load
Compliance References:
UL: UL 1950 (per DNB report)
CG: USCG CFR 183.410 (Ignition protected)
EN: EN 60335-1
CE: Carries the CE mark
ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13.
Options:
Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
601.07 |
|
|
PT-24-95U Battery Charger
“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.
A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.
Features:
24-volt model
“Smart” circuitry provides three-stage charging – bulk, absorption, float
Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages
Multiple isolated output banks; ammeter indicates total output current
The optional sensor adjusts output voltage based on battery temperature
Current limiting prevents damage from overloading
Use as a power supply; can power loads without a battery in line
Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry
Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield
Install in conjunction with PT-MCU for additional control and monitoring
ABS-type approval for battery charging and power supplies
Specifications:
Input VAC (50-60 Hz.): 90-264
Input Amps @ Full Load: @ 115 VAC: 26, @ 230 VAC: 14
Power Factor: .98@115V and .95@230V
Max Output Amps: 95
Output Banks: 3
Battery Capacity (Amp-Hours): 180 – 950
Operating Temp. Rating Reference: T-5
Case Size Reference: A-5
Case Size (H x W x D): 17.5E x 12 x 7.2E inches (44.5E x 30.5 x 18.3E centimeters) *Note with Dripshield installed E add 2” (5.08 cm) to height and 1” (2.54 cm) to depth
Weight Lbs./Kg: 24.5/11
Optional Temp. Sensor Model: TCS-12/24
Remote Panel Model: RP
Compliance Reference: EN, CE, ABS
Temperature Rating References:
Temperature: -20 degrees C to +70 degrees C
Derate Linearly From 100% @ 50 degrees C to 50% @ 70 degrees C
Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation):
Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load
Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load
Compliance References:
UL: UL 1950 (per DNB report)
CG: USCG CFR 183.410 (Ignition protected)
EN: EN 60335-1
CE: Carries the CE mark
ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13.
Options:
Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2704.96 |
|
|
Power-Pac 14AH Power Supply
The 12V DC power supply features built-in backup batteries, which are charged during normal operation and then continue to power radios and critical navigation equipment when AC power is lost. The Power-Pac is ideal for commercial vessels, work boats, and yachts.
The Power-Pac’s highly regulated, low-rising 10-amp output powers radios and other sensitive communications equipment without causing RF or audio interference. At the same time, it floats and charges one or two (depending on the model) built-in 7-amp/hour backup batteries. These are kept at peak charge during the normal functioning of the unit when AC is being supplied. In the event of a loss of AC power, the internal batteries automatically take over to power communication equipment, providing a true uninterruptible DC source.
Features:
Highly regulated, low ripple, noise-free 12-volt output
Built-in, “on-line” stand-by battery provides immediate backup power in case of AC power loss
Internal mounting space and terminals for conversion of the 7 A/H model into the 14 A/H model
Output “Normal” indicator L.E.D.
“Back-up power only” warning light
Audible and visual low battery (10.7 VDC) voltage indicators
Low battery warning buzzer mute switch
Automatic low battery (10.3 VDC) voltage disconnect
Low voltage disconnect override button
Over-voltage protection
Current limit protection
Input/output fused
Separate output terminals are provided for charging external batteries
115/230 50-60 Hz input, selected by a slide switch on the rear panel
Specifications:
Battery Capacity: 14 amp/hour
Case Size (H x W x D): 5.3 x 9.0 x 10.5 inches (13.3 x 22.9 x 26.7 centimeters)
Weight: 24 lbs. (10.9 kg)
Input: 115/230 VAC, 50-60 Hz.
Output: 13.6 VDC @ 5A cont., 10A Int.
Regulation: 1% line and load
Ripple: 1% P-P
Operating Temp: 0-40 degrees C
With a 14 Amp/Hour Battery Installed, the Unit Provides Approximately the Following Power:
7 amps for 100 min.
10 amps for 60 min.
15 amps for 30 min.
20 amps for 15 min
*Assuming battery at full charge when a.c. power failed.
The Power-Pac 7 A/H (single battery model) can power a 25-watt transceiver for up to 3 hours, based on a 20% transmit/receive duty cycle. Power-Pac 14 A/H can provide the same service for up to 6 hours. Provision is made for expanding backup power up to twelve hours (in this example, longer under lesser loads) with the installation of additional externally wired batteries (total 28 amps/hours max.). Batteries are automatically recharged when the AC is restored.
The operator is kept informed of all important functions, such as AC input, DC output, and battery status, with front panel indicator lights and a low battery warning buzzer.
Protection:
AC Input fuse
Internal and external Battery fuses
Over Voltage
Current Limit
Automatic Thermal Shutdown
Low Battery Disconnect
Mechanical Details:
Vinyl Laminated aluminum case
6’ standard AC power cord
Ac input selector switch
Battery Details:
Sealed Lead Acid, Deep-cycle.
Certified by DOT and IATA for shipment by Air
Weight per 7 AH Battery: 6 lbs.
Size (inch): 6” x 3.75” x 2.5”
Options:
Form C AC Failure Contacts (Contact factory for details)
Extra batteries, sold separately 7 A/H increments; each Power Pac will accommodate 28 A/H max. (14 internal, 14 external)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
873.17 |
|
|
Power-Pac 7AH Power Supply
The 12V DC power supply features built-in backup batteries, which are charged during normal operation and then continue to power radios and critical navigation equipment when AC power is lost. The Power-Pac is ideal for commercial vessels, work boats, and yachts.
The Power-Pac’s highly regulated, low-rising 10-amp output powers radios and other sensitive communications equipment without causing RF or audio interference. At the same time, it floats and charges one or two (depending on the model) built-in 7-amp/hour backup batteries. These are kept at peak charge during the normal functioning of the unit when AC is being supplied. In the event of a loss of AC power, the internal batteries automatically take over to power communication equipment, providing a true uninterruptible DC source.
Features:
Highly regulated, low ripple, noise-free 12-volt output
Built-in, “on-line” stand-by battery provides immediate backup power in case of AC power loss
Internal mounting space and terminals for conversion of the 7 A/H model into the 14 A/H model
Output “Normal” indicator L.E.D.
“Back-up power only” warning light
Audible and visual low battery (10.7 VDC) voltage indicators
Low battery warning buzzer mute switch
Automatic low battery (10.3 VDC) voltage disconnect
Low voltage disconnect override button
Over-voltage protection
Current limit protection
Input/output fused
Separate output terminals are provided for charging external batteries
115/230 50-60 Hz input, selected by a slide switch on the rear panel
Specifications:
Battery Capacity: 7 amp/hour
Case Size (H x W x D): 5.3 x 9.0 x 10.5 inches (13.3 x 22.9 x 26.7 centimeters)
Weight: 18 lbs. (8.2 kg)
Input: 115/230 VAC, 50-60 Hz.
Output: 13.6 VDC @ 5A cont., 10A Int.
Regulation: 1% line and load
Ripple: 1% P-P
Operating Temp: 0-40 degrees C
With a 7 Amp/Hour Battery Installed, the Unit Provides Approximately the Following Power. *7 Amps for 40 Min.
10 amps for 20 min.
15 amps for 10 min.
20 amps for 4 min.
*Assuming battery at full charge when a.c. power failed.
The Power-Pac 7 A/H (single battery model) can power a 25-watt transceiver for up to 3 hours, based on a 20% transmit/receive duty cycle. Power-Pac 14 A/H can provide the same service for up to 6 hours. Provision is made for expanding backup power up to twelve hours (in this example, longer under lesser loads) with the installation of additional externally wired batteries (total 28 amps/hours max.). Batteries are automatically recharged when the AC is restored.
The operator is kept informed of all important functions, such as AC input, DC output, and battery status, with front panel indicator lights and a low battery warning buzzer.
Protection:
AC Input fuse
Internal and external Battery fuses
Over Voltage
Current Limit
Automatic Thermal Shutdown
Low Battery Disconnect
Mechanical Details:
Vinyl Laminated aluminum case
6’ standard AC power cord
Ac input selector switch
Battery Details:
Sealed Lead Acid, Deep-cycle.
Certified by DOT and IATA for shipment by Air
Weight per 7 AH Battery; 6 lbs.
Size (inch): 6” x 3.75” x 2.5”
Options:
Form C AC Failure Contacts (Contact factory for details)
Extra batteries, sold separately 7 A/H increments; each Power Pac will accommodate 28 A/H max. (14 internal, 14 external)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
732.37 |
|
|
PT-24-13W Battery Charger
“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.
A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.
Features:
24-volt model
“Smart” circuitry provides three-stage charging – bulk, absorption, float
Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages
Multiple isolated output banks; ammeter indicates total output current
The optional sensor adjusts output voltage based on battery temperature
Current limiting prevents damage from overloading
Use as a power supply; can power loads without a battery in line
Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry
Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield
Install in conjunction with PT-MCU for additional control and monitoring
ABS-type approval for battery charging and power supplies
Specifications:
Input VAC (50-60 Hz.): 90 – 132, 180 – 264
Input Amps @ Full Load: @ 115 VAC: 6.5, @ 230 VAC: 4
Power Factor: .7
Max Output Amps: 13
Output Banks: 3
Battery Capacity (Amp-Hours): 26 – 130
Operating Temp. Rating Reference: T-2
Case Size Reference: A-1
Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (28.4A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth
Weight Lbs./Kg: 8/4
Optional Temp. Sensor Model: TCS-12/24
Remote Panel Model: RP
Compliance Reference: CG, ABS
Temperature Rating References:
Temperature: -10 degrees C to +60 degrees C
Derate Linearly From 100% @ 50 degrees C to 60% @ 60 degrees C
Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation):
Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load
Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load
Compliance References:
UL: UL 1950 (per DNB report)
CG: USCG CFR 183.410 (Ignition protected)
EN: EN 60335-1
CE: Carries the CE mark
ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13.
Options:
Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
706.67 |
|
|
PT-24-20U Battery Charge
“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.
A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.
Features:
24-volt model
“Smart” circuitry provides three-stage charging – bulk, absorption, float
Gel-cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages
Multiple isolated output banks; ammeter indicates total output current
The optional sensor adjusts output voltage based on battery temperature
Current limiting prevents damage from overloading
Use as a power supply; can power loads without a battery in line
Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry
Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield
Install in conjunction with PT-MCU for additional control and monitoring
ABS-type approval for battery charging and power supplies
Specifications:
Input VAC (50-60 Hz.): 85 – 135, 170 – 270
Input Amps @ Full Load: @ 115 VAC: 6.8, @ 230 VAC: 4.3
Power Factor: .7
Max Output Amps: 20
Output Banks: 3
Battery Capacity (Amp-Hours): 40– 200
Operating Temp. Rating Reference: T-3
Case Size Reference: A-2
Case Size (H x W x D): 13.85B x 9.5 x 4.8B inches (35.2B x 24.1 x 12.2B centimeters) *Note with Dripshield installed B add .75” (1.9 cm) to height and 1.35” (3.4 cm) to depth
Weight Lbs./Kg: 12/6
Optional Temp. Sensor Model: TCS-12/24
Remote Panel Model: NA
Compliance Reference: CG, ABS
Temperature Rating References:
Temperature: -20 degrees C to +60 degrees C
Derate Linearly From 100% @ 50 degrees C to 60% @ 60 degrees C
Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation):
Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load
Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load
Compliance References:
UL: UL 1950 (per DNB report)
CG: USCG CFR 183.410 (Ignition protected)
EN: EN 60335-1
CE: Carries the CE mark
ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1137.16 |
|
|
Magic 12/24-10 DC Converter
For The Toughest Tasks
The Mac and Magic DC-DC converters are designed for the toughest conditions for professional, semi-professional and recreational purposes. Even under the most extreme conditions, these DC-DC converters operate faultlessly, giving you round-the-clock output when necessary. The sustainability and technologies that underpin the Mastervolt concept have long been proven in practice. With an MTBF of 280,000 hours at full capacity and 24/7 use, the DC-DC converters are ideal for the toughest tasks and any situation that requires a reliable power supply.
Making The Best Even Better
The reliability and long lifespan of Mastervolt’s DC-DC converters have been established beyond doubt over the past 20 years. While the Mastervolt products have evolved with the latest technological developments, the dimensions and connections have remained the same. As a result it is exceptionally easy to replace one unit with another with only negligible downtime.
Mastervolt Green by Heart
As part of our constant search for eco-friendly and long-lasting solutions, Mastervolt has developed the Green by Heart program. Its impact on the Mac & Magic DC-DC converters include:
An exceptionally effective use of the consumed input current (cos phi) > 0.98!
Faster charging of batteries, even with when the input current is limited
Use of top quality components with a long lifespan
Savings in weight and space
Fewer installation materials
MasterBus Compatible
For the DC-DC converters you can use the MasterBus Serial Interface. All you need is a single cable with one connection. Your benefits: Fast and easy installation, plus centralized monitoring, configuration and operation of your system with a MasterView panel.
Programmable via Desktop or Laptop/PC
Remote control the Mac or Magic via your laptop or PC or configure your personal preferences. The device has a communication port and easy installation with a PC-Link and MasterAdjust software.
Energy-Saving Dimmer Function
Many standard light dimmers convert part of the energy to heat and also lose unnecessary energy. The Mastervolt Magic converters regulate the power supply efficiently and without excessive heat build-up, up to 580 watts for optimal safety (multiple Magic converters can be used for multiple lamps).
Parallel Operation
If you have many/heavy power-consuming devices onboard, the parallel use of several units allows capacities of 40, 60 or more Amps. Advanced high-frequency technology with modern microprocessors ensures minimum power loss when switching from 24 to 12 V and vice versa.
Powerful Selling Points:
Reliable and very stable DC supply
For 12 and 24 V battery systems
Parallel switching of multiple units for capacities of 40, 60 or more Amps
Battery charger and dimmer function
Adjustable output voltage
Voltage stabilization for a longer lifespan of halogen lights, etc
Corrosion-proof aluminium casing
Shock-proof
Temperature-powered fan for cooling
Generates limited heat, so installable almost anywhere
Fully MasterBus compatible with a MasterBus Serial Interface
Specifications:
Nominal output voltage: 27.2 V
Output voltage (adjustable with MasterAdjust): 20-28.5 V
Output voltage dimmer (adjustable with MasterAdjust): 8-26 V
Output voltage stabilization: 2% at extremes of temperatures, load and input
Output voltage ripple (peak peak): max. 1%
Max. output power: 300 W
Nominal output power: 300 W
Max. output current: 10A
Output charge current (3-step mode): 8 A
Nominal input voltage: 12V
Input voltage range: 11-16V
Input voltage range (3-step charge mode): 12-16V
Lower input set point (adjustable with MasterAdjust): 10V
Delay lower input set point (adjustable with MasterAdjust): 30 sec.
Galvanic isolation: yes
Voltage limited: yes
Efficiency: > 90% at nom. input voltage, full load; peak 92 %
Dimmer function: yes, by external momentary switch via fast-on connection, to be activated by DIP switch setting
Alarm contact: yes (fast-on connector)
Dimensions, HxWxD: 227 x 154 x 81mm / 8.9" x 6.1" x 3.2"
Weight: 1.8kg / 4.0lb
Approvals: CE
3-Step charge option: yes (DIP switch settings)
DC consumption: < 115 mA
Connections: screw terminals (max. wire size 16 mm² / AWG5)
Temperature range (ambient temp.): -25 °C to 80 °C, derating > 40 °C -13 °F to 176 °F
Sound level: < 48 dBA at 1M
Protection degree: IP21
Protections: against over load & over temperature
Cooling: maintenance free vario fans
MasterBus compatible: yes, in combination with a MasterBus Serial Interface
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
443.21 |
|