|
PA D5000.5 PAD Series 5-Channel Amplifier - 500W
When install space is at a premium, but your sound system demands plenty of power to realize its full potential, Polk Audio’s new super-efficient D Series amplifiers are a very cool solution.
Polk's PA D5000.5 5-channel amplifier may be small, but it can power your complete system, sending 70 watts RMS to each of your front and rear speakers and up to 500 watts RMS to a sub. Or, you can switch this little beast to 3-channel mode to drive a couple high-level components with 200 watts RMS each and still have that 500 watts RMS left over for the bass. However you use it, this amplifier will fit in almost any location.
Separate high- and low-pass filters on the front and rear channels allow this versatile amp to run a variety of speaker systems, like bi-amped mid-bass and tweeter components, or two front speakers and a sub.
Features:
Super-Efficient Class D Bridgeable Design - Runs cooler than conventional amps.
High-Speed MOSFET Switching power supply.
Front and rear level controls.
Protection - thermal, DC offset, reverse polarity and short circuit.
Nickel-plated wire terminals and RCA connectors.
Stainless steel hardware.
Technical Specifications:
Number of Channels - 5
Frequency Response - 20Hz - 20KHz
2 Ohm RMS Power (14.4V) Per Channel - 4 x 100W, 1 x 400W
4 Ohm RMS Power (14.4V) Per Channel - 4 x 70W, 1 x 200W
4 Ohm RMS Power Bridge (14.4V) Channel - 2 x 200W
Signal-to-Noise Ratio - >105dB
Product Dimensions (with panels) (H x W x D) -1-13/16'' x 13-5/16'' x 6.75''
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
475.57 |
|
|
PA D4000.4 PAD Series 4-Channel Amplifier - 400W
When install space is at a premium, but your sound system demands plenty of power to realize its full potential, Polk Audio’s new super-efficient D Series amplifiers are a very cool solution.
Polk's PA D4000.4 4-channel amplifier may be small, but it can power your front and rear speakers with up to 125 watts RMS each. Or, you can switch this little beast over to 2-channel mode to drive a couple subwoofers with up to 200 watts RMS each. However you use it, this amplifier will fit in almost any location.
Separate high- and low-pass filters on the front and rear channels allow this versatile amp to run a variety of speaker systems, like bi-amped mid-bass and tweeter components, or two front speakers and a sub.
Features:
Super-Efficient Class D Bridgeable Design - Runs cooler than conventional amps.
High-Speed MOSFET Switching power supply.
Front and rear level controls.
Protection - thermal, DC offset, reverse polarity and short circuit.
Nickel-plated wire terminals and RCA connectors.
Stainless steel hardware.
Technical Specifications:
Number of Channels - 4
Frequency Response - 20Hz - 20KHz
2 Ohm RMS Power (14.4V) Per Channel - 4 x 200W
4 Ohm RMS Power (14.4V) Per Channel - 4 x 125W
4 Ohm RMS Power Bridge (14.4V) Channel - 2 x 400W
Signal-to-Noise Ratio - >105dB
Product Dimensions (with panels) (H x W x D) -1.81'' x 10.94'' x 6.75''
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
376.36 |
|
|
Select S-1100.2 2 Channel Amplifier - 1800W
The SELECT series of amplifiers by DS18 is known for two things - legendary power and striking elegance.
This brushed aluminum amplifier adds a nice touch of sleekness to your sound system. Each amplifier has adjustable crossover settings, gain control, and Hi/Lo pass filters to deliver powerful and accurate sounds that will make you feel like you’re in a concert.
Own an elegant amplifier that provides awesome power and amazing reliability.
Features:
Surface mount component technology
Audio precision quality control verification
Multilayer PCB trace layout
Clipping, power, and protection LED indicator
Short circuit, thermal, and voltage protection
Precise filters so you can get the perfect sound from your speakers
Technical Specifications:
Number of Channels - 2
Frequency Response - 20Hz - 200KHz
2 Ohm RMS Power (14.4V) Per Channel - 2 x 80W
4 Ohm RMS Power (14.4V) Per Channel - 2 x 60W
Signal-to-Noise Ratio - >90dB
Product Dimensions: (L x W x H) - 7.4" x " x 1.87" (18.8 x 5.83 x 4.75 cm)
*Sold as an Individual
|
149.94 |
|
|
ASK902B.6 4 Channel Amplifier & 6.5" Speaker Kit - White
No room for a stereo head unit? Want to listen to your music from a Bluetooth enabled device? No worries. Boss has taken audio to the next level with a powerful amplifier and weatherproof speaker kit.
This kit packs a punch with the MC900B 4-Channel amplifier w/multi-function controller, a pair of 6.5" MR6W speakers, waterproof pouch and a USB/Aux accessory extension cable.
All in one and ready to play all your music on the water or in any environment.
Features:
Weatherproof 6.5" MR6W speakers - White
Hideaway antenna
4-Channel Weatherproof 500W amplifier with multi-function controller -
Included in the Box:
MC900B Bluetooth amplifier w/multi-function controller
One (1) pair of MR6W speakers
Waterproof pouch
MUSB35 USB/Aux Accessory Extension Cable
Mounting hardware
Instruction manuals
*SiriusXM Promotion - Get 3 Free Months SiriusXM Streaming Service - LINK
*Sold as an Individual Kit
|
176.96 |
|
|
ASK904B.64 4 Channel Amplifier & 2 Pairs of 6.5" Speaker Kit - White
No room for a stereo head unit? Want to listen to your music from a Bluetooth enabled device? No worries. Boss has taken audio to the next level with a powerful amplifier and weatherproof speaker kit.
This kit packs a punch with the MC900B 4-Channel amplifier w/multi-function controller, a two (2) pairs of 6.5" MR6W speakers, waterproof pouch and a USB/Aux accessory extension cable.
All in one and ready to play all your music on the water or in any environment.
Features:
Weatherproof 6.5" MR6W speakers - White
Hideaway antenna
4-Channel Weatherproof 500W amplifier with multi-function controller -
Included in the Box:
MC900B Bluetooth amplifier w/multi-function controller
Two (2) pairs of MR6W speakers
Waterproof pouch
MUSB35 USB/Aux Accessory Extension Cable
Mounting hardware
Instruction manuals
*SiriusXM Promotion - Get 3 Free Months SiriusXM Streaming Service - LINK
*Sold as an Individual Kit
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
199.16 |
|
|
MS-AM504 4-Channel Marine Amplifier - 500W
Features:
Marine Grade Chassis - Stainless steel end caps and bottom plate provide a stunning finish with added environmental protection.
Heat Sink Technology - Heat sink technology transfers heat more efficiently and offers more thermal stability for maximum component reliability.
Class-AB Design - The 500 Watt 2-Ohm stable (per channel) design ensures clean and powerful amplification of the input signal,enough to rock the boat.
Conformal Coated Circuitry - Provides added protection from salt air and moisture to ensure maximum product life.
RCA Line Out - A pass through RCA output enables linking of multiple amplifiers for enhanced system performance.
4 Channels - Capable of powering 4 speakers, a sub and a pair of speakers or 8 speakers in parallel (2 speakers per channel in parellel @ 2 Ohms).
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
277.36 |
|
|
HYDRO Full Range Digital Marine 4-Channel Amplifier - 720W
Whether you are the type of audio enthusiast that likes to hit the open road on his bike, ride the rough trails on your side by side, or cruise the open waters, you are going to need a powerful and waterproof rated amp that has a small footprint and also make great power.
DS18 has a line just for the job with the NXL series of amplifiers to power your whole system. This 4 channel amplifier helps you accommodate for all your different speaker setups without having to look further. Being a full range amps, these can be run on subs, mids, or tweeters because of the internal design of the amp.
All units have stable and reliable 4-layer PCB layouts, IPX67 rated for power sports, has an ultra-compact size for easy installation, and has audio precision quality control verification.
Features:
Stable and reliable 4 layers PCB layout design
IPX67 Waterproof for Powersports applications
Ultra compact size for easy installation
Audio precision quality control verification
Technical Specifications:
Number of Channels: 4
Frequency Range: 20Hz - 20KHz
Max Power: 720W
2 Ohm RMS Power Per Channel: 150W x 4
4 Ohm RMS Power Per Channel: 100W x 4
4 Ohm Bridged Power Per Channel: 260W x 2
Signal-to-Noise Ratio: 90 dB
Dimensions (L x W x H) - 200mm x 93.4mm x 39.8mm
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
335.94 |
|
|
HYDRO Full Rangle Digital Marine 2-Channel Amplifier - 600W
Whether you are the type of audio enthusiast that likes to hit the open road on his bike, ride the rough trails on your side by side, or cruise the open waters, you are going to need a powerful and waterproof rated amp that has a small footprint and also make great power.
DS18 has a line just for the job with the NXL series of amplifiers to power your whole system. This 4 channel amplifier helps you accommodate for all your different speaker setups without having to look further. Being a full range amps, these can be run on subs, mids, or tweeters because of the internal design of the amp.
All units have stable and reliable 4-layer PCB layouts, IPX67 rated for power sports, has an ultra-compact size for easy installation, and has audio precision quality control verification.
Features:
Stable and reliable 4 layers PCB layout design
IPX67 Waterproof for Powersports applications
Ultra compact size for easy installation
Audio precision quality control verification
Technical Specifications:
Number of Channels - 2
Frequency Range: 50Hz - 250KHz
Max Power - 900W
2 Ohm RMS Power Per Channel - 150W x 2
4 Ohm RMS Power Per Channel - 100W x 2
4 Ohm Bridged Power Per Channel - 300W x 1
Signal-to-Noise Ratio - 90 dB
Dimensions (L x W x H) - 7.87" x 3.68" x 1.57"
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
335.94 |
|
|
NXL 1-Channel Full-Range Class D Marine/Powersports Amplifier - 1500W RMS, 1-Ohm
Elevate your marine sound experience to new heights with DS18's NXL-X1500.1FR. Designed to deliver the best performance for your marine speakers, this digital class amplifier is the ultimate choice for those who refuse to settle for anything less than exceptional.
Featuring an innovative Input Selector, this amplifier allows you to effortlessly choose between multiple signal sources. This flexibility ensures that you can easily customize your audio setup according to your preferences. This amplifier’s Full Range Capabilities also give users the option of powering either subs or mids and highs.
Not only does DS18's NXL-X1500.1FR deliver unparalleled performance, but it also boasts an IPX6 Waterproof Rating, protecting against water intrusion. Additionally, this amplifier is built to withstand harsh marine conditions with its UV, Salt, and Fog protection. It's designed to endure whatever nature throws at it without compromising sound quality.
With its Direct Power harness design featuring marine-grade OFC tinned wires, this amplifier ensures optimal power transfer and efficiency. We’ve also included a 150A Fuse to protect you and your boat from almost any electrical short related to the amp's installation. Every detail has been carefully crafted to provide you with a seamless and hassle-free installation process.
Experience the future of marine amplification with the latest digital amplifier design and SMC technology, including both high pass and low pass filters for the one output channel. This bandpass filter system enhances audio clarity and precision, allowing you to enjoy every note with exceptional clarity and detail.
Prepare to be blown away by the NXL-X1500.1FR's staggering performance, delivering 700W RMS at 4 ohms, 1000W RMS at 2 ohms, and 1500W RMS @ 1 ohm. These power settings are guaranteed to supercharge any custom marine build.
Don't settle for mediocre sound on your boat or power sports vehicle. Upgrade to the DS18 NXL-X1500.1FR Marine & Powersports Digital Amplifier and unleash the true potential of your marine speakers.
Features:
Marine Full Range
1 Channel
1 X 1500 Watts @ 1 Ohm
Built-in Crossover
Class D
Water Resistant - IP67
Technical Specifications:
Number of Channels - 1
Frequency Response - 10Hz-250Hz
4 Ohm RMS Power - 700W
2 Ohm RMS Power - 1000W
Signal-to-Noise Ratio - >81dB
Product Dimensions (L x W x H) - 13.4" x 4.4" x 1.77"
|
659.94 |
|
|
ME-60 4 Channel Amplifier - 120 Watts
The ME60 is a four channel 120 Watts RMS audio amplifier of delivering up to 30W RMS per channel. It has a compact, water resistant design that allows for flexible mounting possibilities, and makes it simple to expand the audio system capabilities for any installation.
Features:
To add additional loudspeakers to a current audio system
To provide amplification for a separate audio zone
Powers up to eight (8) 4ohm speakers
Internal distortion limiting circuits
Dedicated gain level control
External volume control with ON/OFF switch included
Rear channels switchable from full range to powered sub out
Specifications:
Number of Channels - 4
Speaker Impedance - 2-8 ohm
4 Ohm RMS Power - 4 x 20 W
2 Ohm RMS Power - 4 x 30 W
Frequency Response - 20Hz-40kHz
Dimensions (W x H x D) - 6.9" x 4.5" x 1.4" (175mm x 115mm x 35mm)
Volume Control Cable Length - 114" (290 cm)
*Sold as an Individual
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
53.94 |
|
|
ME-52 2 Channel Amplifier - 50 Watts
The ME-52 is a compact 2-channel 50-watt audio amplifier with separate volume control. This unit is designed for adding additional speakers to an existing system or as a separate zone amp.
Features:
To add additional loudspeakers to a current audio system
To provide amplification for a separate audio zone
Powers up to four (4) - 4ohm speakers
Internal distortion limiting circuits
Dedicated gain level control
External volume control with ON/OFF switch included
Specifications:
Number of Channels - 2
Speaker Impedance - 2-8 ohm
2 Ohm RMS Power - 2 x 25 W
4 Ohm RMS Power - 2 x 15 W
Frequency Response - 20Hz-20kHz
Dimensions (W x H x D) - 4-3/16" x 1-9/16" x 4-7/8" (106mm x 39mm x 124mm)
Volume Control Cable Length - 114" (290 cm)
*Sold as an Individual
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
79.93 |
|
|
SG-24DA61500 Signature Series 1500W - 6 Channel Amplifier - 24V
The Signature Series 24-volt 6-channel marine amplifier is designed for boats operating on 24-volt electrical systems. With a peak power of 1500-watts, it provides incredible power delivery to your onboard audio entertainment. The plug-and-play setup allows for easy installation without the need for an additional power adaptor.
Fusion Signature Series amplifiers are purpose-built for the marine environment. Boasting some of the most impressive environmental protection available, they deliver a Signature performance on the water like never before.
Features:
Class-D Amplifier Technology: The highly efficient Class-D design provides 1500-watt peak power while drawing less current than a standard Class-AB amplifier. This design provides increased efficiency and power output to your speakers and subwoofers, letting you enjoy your music for longer without needing to worry about battery drain.
1500-Watt Peak Power: With a peak power of 1500-watts, you can easily power up to 6 pairs of speakers OR up to 4 pairs of speakers and 1 subwoofer.
Marine-Ready Design with Conformal Coated PCBs: Extending the life of your amplifiers, the Signature Series amplifiers are designed specifically for marine use with conformal coated PCBs to provide extra protection from the marine elements.
Rigid Aluminum Alloy Heat Sink: Molded to form a singular die-cast chassis, the fin layout is calculated with precision to increase the surface area of the heat sink and improve heat dissipation.
Stainless Steel Mirror Finish: The polished stainless steel control panel cover conceals and helps protect all cable connections and the settings control panel while providing an attractive finish to complement any installation.
Speaker Configuration: Whether you require 2 ohms per channel or 4 ohms bridged, the Signature Series amplifier has your installation options covered to achieve optimum output levels. Connect up to 2 speakers per channel (2 x 4 ohm speakers in parallel) with the SG-24DA61500.
Zone Designation: To align with the Fusion Entertainment System Zone philosophy, the input and output connections are labeled as zones.
Technical Specifications:
Frequency Response : 10 Hz to 40 kHz (-3dB @ 4 Ohm rated power)
Peak Power Output: 1500 W
Rated Power Output (4 Ohm): 100 W rms x 6 @ 28.8 V input < 1% THD + N (EIA/CEA-490A)
Rated Power Output (2 Ohm): 140 W rms x 6 @ 28.8 V input < 1% THD + N (EIA/CEA-490A)
Rated Power Output (4 Ohm Bridged): 280 W rms x 3 @ 28.8 V input < 1% THD + N (EIA/CEA-490A)
Input Sensitivity: 0.3 V to 8 V rms, user adjustable
Input Impedance: 7k Ohm nominal
High-Pass/Low-Pass Full Range Filter: Yes, user selectable
Filter Cross-Over Frequency: 32 Hz to 320 Hz, user adjustable
Bass-Boost: 0 to 9 dB, user adjustable (zone 3 only)
Operating Voltage: 21.6 V to 32 V dc
Remote Switch-On: Yes - 6 V threshold
Current Consumption (Standby): < 1 mA @ 28.8 V input
Current Consumption (Idle): < 1.25 A @ 28.8 V input
Current Consumption (Max): 35 A @ 28.8 V input
Fuse Rating: 3 x 20 A ATC Blade-Type (SAE J1171 Compliant)
Protection Circuits: Reverse-Voltage, Input Under/Over Voltage, Over-Temperature, Output Short-Circuit
Operating Temperature Range: 0 to 50°C (32 to 122°F)
Ingress Protection Rating: Dry area installation only
Dimensions: 420 mm (L) x 210 mm (W) x 57 mm (H) or 16-9-16" (L) x 8-1/4" (W) x 2-1/4" (H)
Weight: 5.15 kg or 11.35 lb with cover
Warranty: 3 years
In the Box:
Four 8-gauge, self-tapping screws
3 mm hex key (for the top cover and power terminals)
2.5 mm hex key (for the speaker terminals)
Polishing cloth
Spare J1171 compliant 20 A blade-type fuses (only included with 24-Volt Signature Series 6 Channel 1500-Watt amplifier)
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
779.99 |
|
|
MA754AM 4-Channel Amplifier - 75W
The marine A754 4-channel amplifier delivers a powerful 75-watt RMS to each of the front and rear speakers in a boat. You can also bridge the amp to 2-channel mode to drive a couple of subs with a 200-watt RMS or 3-channel mode to drive both a pair of full-range speakers and a subwoofer.
Speaker-level inputs allow this amplifier to integrate into almost any system, even one using a marine factory radio. Separate high-pass and low-pass crossovers on the front and rear channels allow users to dial in the perfect roll-off to best suit speaker placement and cabin acoustics.
Features:
Compact size
High and low-level input
Variable crossover and bass boost
Low noise and distortion
Input Level Control
Full on-board protection
Phase Switch
RBC wired remote
Class D amp technology
Turn-on mode
General Specifications:
4-channel marine amplifier
75 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms)
200 watts RMS x 2 at 4 ohms in bridged mode (4-ohm stable in bridged mode)
Variable high- and low-pass filters (32-320 Hz, 12 dB/octave) on front and rear channels
Preamp and speaker-level inputs
Preamp outputs
Fuse rating
30A x 2
8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
Dimensions (W x H x D) 320mm x 51.3mm x 180mm (12-5/8” x 2-1/16" x 7-1/8”)
What’s in the Box:
One marine A754 4-channel amplifier
4 Bare wire-to-RCA adapters
Four 30A ATO fuses (2 installed, 2 spare)
Two JBL stickers
Owner's Manual
4 Mounting screws (M4 x 53mm)
1 logo badge
|
269.21 |
|
|
POWER760 4-Channel Amplifier - 760W
Time to stretch your sound muscles with the POWER760 4 channel amplifier. It tops out at 760W of peak power, has a protection circuit that safeguards against short circuits, DC offset and thermal overload, a channel mode selector which allows you to switch from 4, 3 or 2.
It's time to include this audio 4 channel amplifier in your sound system.
Features:
Designed to meet CEA-2006 test standards
Compact design allows great flexibility in mounting
MOSFET power supply
Channel mode selector switch - 4, 3 and 2 channel
Technical Specifications:
Number of Channels - 4
Frequency Response - 20Hz - 20KHz
2 Ohm RMS Power Per Channel - 2 x 190W
4 Ohm RMS Power Per Channel - 4 x 100W
4 Ohm RMS Power Bridge Channel - 4 x 75W
Overall Dimension (W x H x L) - 9" x 2.5" x 12.5"
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
129.67 |
|
|
Candy-X4B 4 Channel Amplifier - 1600W
Small, compact, and powerful is what the DS18 Candy-X4B amplifier is all about. Just like edible candy, we have many different flavors to choose from to give audio enthusiasts goosebumps when they turn it up. Instead of making your mouth tingle, DS18 Candy Amplifiers make your ears tingle with pleasure when you hook them up to any line of pro audio, marine, and power sports audio.
These amplifiers not only have the power to keep your speakers at maximum wattage efficiently, but they are also very small and compact in design so they can be mounted almost anywhere and still not have to worry about room.
DS18 Candy amplifiers are perfect for people who want a very small audio footprint with also having all the benefits of a huge amplifier putting out lots of power in a small package.
Features:
One of our most popular lines of automobile amplifiers because of its power output to size ratio
Small and powerful design that gives it a wide range of versatility because of its size
High-grade components made to stand the test of time and give you loud sound on demand
RCA and Hi/Lo inputs so you can integrate this amp into your factory audio system easily
Technical Specifications:
Number of Channels - 4
Frequency Response - 20Hz - 20KHz
2 Ohm RMS Power (14.4V) Per Channel - 4 x 120W
4 Ohm RMS Power (14.4V) Per Channel - 4 x 80W
Signal-to-Noise Ratio - >100dB
Product Dimensions: (L x W x H) - 9.21" x 5" x 1.87" (23.4 x 12.7 x 4.75 cm)
*Sold as an Individual
|
239.94 |
|