Trolling Motor Saver Set for Bass Boats A must for every trolling motor.  Keeps motor firmly mounted to the boat, and more importantly it keeps the trolling motor secure with less bouncing when traveling down the lake.   Adjustable 9" to 18"

Trolling Motor Saver Set for Deep V Boats Specially designed for deep "V" boats with extra long trolling motor shafts.  Designed with two straps,  the longer strap is mounted where the trolling motor shaft fastens to the mounting bracket and can mount 24" above the deck.  The second strap is designed to hold down the actual motor.  It wraps around the entire mounting bracket, and the trolling motor shaft, helping to keep the motor from bouncing when traveling down the lake.  Keep your trolling motor tied down securely and undamaged for longer life.  Adjustable 9" to 24".

Trolling Motor Propeller Cover The cover keeps the trolling motor and prop from cutting a hole in your boat tarp during transport.  This complete cover protects the motor as well as the tarp. There is an additional webbing liner inside the cover for increased protection from the trolling motor prop. The cover will fit up to a 12" trolling motor prop and is 19" in length.  It is also designed for the trolling motor prop to be positioned on the inside of the boat vs. the outside.

Trolling Motor Mount f/GT36 and GT56  Easily attach your compatible 4- or 8-pin scanning transducer to the trolling motor of your boat with this mount. Its low-profile design provides ultimate protection from underwater obstructions and easy mounting.

XTM 9 20 MSI T Trolling Motor Transducer f/MEGA Units MEGA SI, MEGA DI, DualBeam PLUS, 20/60/86/55 degrees, 200/83/455/800 kHz and 1.2 MHz, temperature built-in trolling motor transducer. For HELIX MEGA Side Imaging units only. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Replacement Cable for Trolling Motor Pull Rope Never worry about that trolling motor pull rope breaking again. This stainless steel vinyl coated braided cable is used to replace the manufacturer's pull rope on your trolling motor. This replacement cable will not rust, break or rot. It comes with complete, easy to follow installation instructions. Don't wait for your rope to break, replace it with this durable steel cable now. 

Trolling Motor Mount for MK, Garmin, Rhodan, & Power Pole The Sea Swivel is a heavy-duty marine-grade pivoting bracket designed to maneuver a trolling motor in the correct position while being deployed. This bracket also has the benefit of being able to adjust the stowed position to match the angle of any boat. That means no more anchor hatches covered up and no more trolling motorheads hanging off the side of the boat. All that is needed is an 8" x 8" flat mounting surface and access under the gunwale to tighten the nut. During installation, it is recommended that users apply teff-gel or marine-grade grease to the main bolt threads and the bearing assembly. Features: Maneuverability and Positioning The Sea Swivel offers a heavy-duty pivoting bracket that allows users to easily maneuver the trolling motor into the correct position while deployed. This is especially useful for maintaining proper control and direction while fishing or navigating in different conditions. Adjustable Stowed Position The ability to adjust the stowed position of the trolling motor to match the angle of the boat is a significant advantage. This means that the trolling motor won't interfere with anchor hatches or hang off the side of the boat when not in use, enhancing the boat's aesthetics and functionality. High-Quality Materials The use of 7075T6 aluminum alloy, commonly found in the aerospace industry, provides peak strength and ensures the Sea Swivel's durability. This material choice suggests that the product is designed to withstand the rigors of marine environments and provide longevity. Corrosion Resistance The anodized finish is designed to protect the Sea Swivel from the harsh marine environment, which typically includes exposure to saltwater and other corrosive elements. This coating enhances the product's ability to resist rust and other forms of corrosion over time. Stainless Lock Pin and Hardware The utilization of all 316 stainless lock pins and mounting hardware further enhances the product's resistance to corrosion, as 316 stainless steel is known for its exceptional corrosion resistance properties, making it well-suited for marine applications. Backing Plate for Strength The inclusion of a pre-cut backing plate to be placed under the mounting surface is a smart design choice. This additional plate strengthens the installation area, reducing the risk of damage or failure due to stress or strain over time. Easy Installation The patent-pending design and single-bolt mounting system contribute to streamlined installation processes. This can be a significant selling point for customers, as it saves time and effort during setup. *It is recommended that users apply teff-gel or marine-grade grease to the main bolt threads and the bearing assembly. Compatibility The Sea Swivel stands out as a versatile solution seamlessly accommodating many makes, models, and sizes of trolling motors. It makes installation a breeze and comes pre-drilled for the quick-release brackets listed below: Minn Kota RTA 54/62 (fits all 36V permanent magnet motors) Minn Kota RTA 55/56 (fits all new Brushless/Quest motors) Minn Kota RTA17 (fits all 24V motors for smaller units) Also fits quick-release mounts for the *Garmin Kraken 24v/36v Rhodan large mount 6 bolt 36v 96/108 Rhodan smaller mount 4 bolt 24v Power Pole Move PV 36V/24V Lifetime Warranty Sea Swivel offers a limited lifetime warranty. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

14" Straight Trolling Motor Plate for Garmin’s Kraken The Sea Brackets 14" Straight Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Dimensions: 14" x 8" x 1/2" Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

16" Straight Trolling Motor Plate for Garmin’s Kraken The Sea Brackets 16" Straight Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

18" Straight Trolling Motor Plate for Garmin’s Kraken The Sea Brackets 18" Straight Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Dimensions: 18" x 8" x 1/2" Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

20" Straight Trolling Motor Plate for Garmin’s Kraken The Sea Brackets 20" Straight Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Dimensions: 20" x 8" x 1/2" Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

Small Offset Trolling Motor Plate for Garmin’s Kraken The Sea Brackets Small Offset Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Dimensions: 18.5" x 13.5" x 1/2" Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

Large Offset Trolling Motor Plate for Garmin’s Kraken The Sea Brackets Large Offset Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Dimensions: 18.5" x 15.5" x 1/2" Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

Large Offset Trolling Motor Plate for Minn Kota’s Quest The Sea Brackets Large Offset Trolling Motor Mounting Plate, designed for Minn Kota’s RTA-55 Quick Release Bracket, offers a robust and reliable solution for installing any Quest Series Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Minn Kota’s RTA-55 Quick Release Bracket Backing disk from Sea Brackets or an alternative backing support system 1/4–20 tapered Phillips machine screws, fender washers, and lock nuts 3/8–16 Flathead Phillips machine screws, fender washers, and lock nuts Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

20" Straight Trolling Motor Plate for Minn Kota’s Quest The Sea Brackets 20" Straight Trolling Motor Mounting Plate, designed for the Minn Kota’s RTA-55 Quick Release Bracket, offers a robust and reliable solution for installing any Quest Series Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Minn Kota’s RTA-55 Quick Release Bracket Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 3/8–16 Flat-head Phillips machine screws, fender washers, and lock nuts Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.