3/8" Backing Disk for Minn Kota Quest - 2-Pack Specifications: Size: 3/8" Backing Disk Specifically for Minn Kota Quest 2-Pack

5/16" Backing Disk for Kraken Mounts - 2-Pack Specifications: Size: 5/16" Backing Disk Specifically for Kraken Mount 2-Pack

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ      230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet     Part # 0115-0064-0300  

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.   March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ          230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet

Clevis Pin - 9.5mm(3/8") x 31.9mm(1-1/4") Grade 316 Stainless Steel 2 Pack

3/8" Sta-Set Performance Cruising Line - Red Fleck - 600'  Sta-Set is the quintessential proven performance double braid.   As the # 1 double braid in America, Sta-Set is a strong, flexible, and long wearing line.  It is high strength, low stretch and extremely durable.  Yet it still remains soft over time.  Sta-Set is both easy to handle and splice.   Applications - A true multi-purpose line used for sheets and controls on a wide range of boats from 420s and Flying Scots to Keelboats.  The ideal line for collegiate programs and sailing schools looking for a high quality line with superior durability and dependability.  Perfect for mainsheets, jib sheets, and control lines.  Technical Specifications: Color - Red Fleck Material -  Double braid polyester sheath with a braided polyester core Rope Diameter - 3/8" (10mm) Rope Length - 600' (183 M) Tensile Strength - 5,100 lb *Sold as an Individual

316 SS Non-Perforated Worm Gear Hose Clamp - 3/8" Band - (1-1/16" – 1-1/2") Clamping Range - 10-Pack - SAE Size 16 Premium Marine Grade, all AISI 316 (high tensile strength) Stainless Steel Compact “HD NON-PERF” Worm Gear Hose Clamp. The 9.7 mm (0.382”) wide band is Non-Perforated and smooth on the inside with rolled edges. This eliminates hose damage with increased clamping force. The high strength, compact, one-piece 14mm (0.55”) wide housing provides one of the highest clamping force ratings of any worm gear style clamp. Features: The screw head is 7mm Long service life and safety for most general-purpose hose applications and connections Recommendations: Measure hose O.D. before selecting clamp size for proper fit Double clamp on each hose end for critical applications Construction: Band & Housing: 316 Stainless Steel 9.7 mm wide band – 0.8mm thick Screw Drive: 316 Stainless Steel 7.0 mm screw head Specifications: SAE Size: 16 Hose Inner Diameter: (inch) 7/8" – 1" Clamping Range: (inch) (1-1/16") – (1-1/2") / (mm) 26-38 Recommended Torque Inch lbs: 35-45

PSS Shaft Seal 1-3/8" Shaft 2-1/4" Tube Shaft Diameter: 1-3/8" Stern Tube Diameter (D): 2-1/4" to 2-3/8" Total Length (A): 7.38" Total Length (compressed) (Compressed A): 6.38" Rotor Diameter (B): 2.875" Carbon Cuff Diameter (C): 2.5" Stern Cuff Length (E): 1.5" The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm). The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation. **As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced." Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

Large Offset Trolling Motor Plate for Minn Kota’s Quest The Sea Brackets Large Offset Trolling Motor Mounting Plate, designed for Minn Kota’s RTA-55 Quick Release Bracket, offers a robust and reliable solution for installing any Quest Series Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Minn Kota’s RTA-55 Quick Release Bracket Backing disk from Sea Brackets or an alternative backing support system 1/4–20 tapered Phillips machine screws, fender washers, and lock nuts 3/8–16 Flathead Phillips machine screws, fender washers, and lock nuts Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

20" Straight Trolling Motor Plate for Minn Kota’s Quest The Sea Brackets 20" Straight Trolling Motor Mounting Plate, designed for the Minn Kota’s RTA-55 Quick Release Bracket, offers a robust and reliable solution for installing any Quest Series Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement. Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Minn Kota’s RTA-55 Quick Release Bracket Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 3/8–16 Flat-head Phillips machine screws, fender washers, and lock nuts Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

MKA-58 Boat Deck Reinforcement Kit Provides additional strength, stability, and versatility for mounting Minn Kota Quest series RT Instinct, Ulterra, Terrova, and RT Terrova trolling motors. Features: Provides additional strength and stability for mounting Minn Kota Quest series trolling motors Helps to distribute torque loads associated with higher thrust motors Can be installed directly to the boat deck or in combination with MKA-56 / RTA-55 quick-release bracket Multiple mounting hole patterns allow for flexible installation Includes stainless steel hardware Designed for use in saltwater Compatible with Ulterra, Terrova, Riptide Terrova, and Riptide Instinct QUEST series trolling motors

Adapter Cable for Minn Kota Transducer to Element 15-Pin Raymarine Adapter cable for Minn Kota Transducer to Element HV display.

Troll-Tamer™ for Minn Kota Maxxum Trolling Motor Stabilizer Lock 5"-8" Spacing  The Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditions The latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.

Troll-Tamer™ for Minn Kota Terrova & MotorGuide Trolling Motor Stabilizer Lock 8"-12" Spacing The Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditions The latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.

Troll-Tamer™ for Minn Kota Terrova & MotorGuide Trolling Motor Stabilizer Lock 5"-8" Spacing The Troll-Tamer™ Trolling Motor Stabilizer Lock is designed to securely hold the trolling motor in place to prevent damage to the trolling motor and boat. No more worries about inadequate hold down devices, the Troll-Tamer™ Trolling Motor Stabilizer Lock has been designed and tested in the nastiest conditions by top touring pros. The Troll-Tamer™ Trolling Motor Stabilizer Lock is machined from 300 Series Stainless Steel and assembled to endure even the roughest conditions The latest models, RMC-108-DP and RMC-109-DP feature a clamp on shaft bracket to work with the latest in digital, wireless bow mount trolling motors, including Minn Kota Terrova, Auto Pilot, Riptide models & Motor Guide Xi5.