|
Simer 2800 Shallow Well Jet Pump, 1/2HP
Simer Shallow Well Jet Pump, Cast Iron Construction, 1/2HP TEFC Motor 115Volt only, 1” NPT Ports, up to 5.1GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth
|
381.42 |
|
|
Simer 2805E-02 Shallow Well Jet Pump, 1/2HP
Simer Shallow Well Jet Pump, Cast Iron Construction, 1/2HP 115/230Volt Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, Best for Shallow Wells to 20 Feet, Maximum Lift 25 Feet, up to 8.5GPM, Adjustable Pressure Switch Set to 30psi On / 50psi
|
465.00 |
|
|
Simer 3105P Shallow Well Jet Pump, 1/2HP
Simer Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 1/2HP 115/230V Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 7.4GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth
|
432.90 |
|
|
Simer 3310P Convertible Jet Pump, 1HP
Simer Convertible Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 1HP 115/230V Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, for Shallow Wells to 25 Feet or Deep Wells to 90 Feet, from 5.3GPM to 20.7GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, Built-in Pressure Regulator, Requires Jet Kit
|
698.25 |
|
|
Sta-Rite SNC-L Shallow Well Jet Pump 1/2HP
1/2 HP - 115/230 Volt - Shallow Well Jet Pump
The ProJet SN Series Pumps provide excellent performance with good pressure for wells to 25 feet deep. Self-priming after the priming chamber has been filled with water.
APPLICATIONS
Water systems and sprinkling
FEATURES
Quality Construction
Close grained cast iron body. Drain port provided for easy winterizing.
Built-in Jet
High strength Lexan nozzle and venturi for maximum resistance to corrosion and abrasion. Clean out plug provided for ease of service.
Noryl Impeller
Precision-molded for perfect balance ultra-smooth for highest performance and efficiency.
Precision Molded Diffuser
Pump primes faster, handles more air, with multi-port, precision-molded, reinforced polypropylene diffuser.
Mechanical Shaft Seal
Precision lapped and highly polished carbonceramic, stainless steel construction. Internal design guarantees continuous water lubrication.
Motor Windings
Superior insulation materials protect against excessive moisture and contaminants assure prolonged motor life.
Balanced Rotor
Die cast under high pressures for uniform performance and greater efficiency, dynamically balanced.
Heavy-duty Ball Bearings
Shielded, permanently lubricated bearings, extensively tested to ensure extended life and smooth, quiet operation.
Pump and Motor Shaft
Stainless steel for maximum corrosion resistance; one-piece threaded shaft for positive impeller drive and alignment.
Dustproof Cover
All electrical components are protected from dirt, dust and insects by a dustproof canopy; ventilating air cannot contaminate vital switching components.
Pressure Switch
Professional quality, allows cut-in adjustments.
SPECIFICATIONS
Max. Liquid Temperature: 140°F
Max. Inlet Pressure: 50 PSI
|
869.76 |
|
|
Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9 GPM (shallow well setup)
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM (shallow well setup)
MAX LIFT: 25' w/ shallow well jet kit / 70' w/ deep well jet kit
MAX PSI: 62 psi (shallow well setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4"
MINIMUM SUCTION PIPE SIZE: 1-1/4"
DRIVE PIPE SIZE: 1"
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
516.00 |
|
|
Flotec FP4332 Thermoplastic Convertible Jet Pump 1 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor - see manual for 115 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1
MAXIMUM CAPACITY: 20.7 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 18.3 GPM (shallow setup)
MAX LIFT: 25' for shallow setup / 90' for deep setup
MAXIMUM PRESSURE: 52 psi for shallow / 56 psi for deep
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW: 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
698.25 |
|
|
Sta-Rite PNC-10 Shallow Well Jet Pump 1/2HP
Sta-Rite Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 1/2HP 115/230V, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 7GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth
|
797.04 |
|
|
Simer BP21X Bronze Paddle Pump, 1” NPT Ports
Simer- Bronze Paddle Pump, 1” NPT Ports, 3/4” 416SS Shaft, up to 28 GPM, 70 Feet of Head Maximum
|
448.60 |
|
|
Flotec FP4212 Cast Iron Convertible Jet Pump 1/2 HP
KEY FEATURES
Superior performance at depths to water of 100' or less
Rugged, heavy-duty pump housing
Ready-to-install dual-voltage 115v/230v motor - see manual for 230 volt conversion
Pressure switch pre-wired with 30-50 PSI pressure setting
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 7.9 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 7.1 GPM (shallow setup)
MAX LIFT: 25' for shallow setup / 70' for deep setup
MAXIMUM PRESSURE: 60 psi (shallow setup) / 54 psi (deep setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"NPT
AMP DRAW (full load): 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
509.25 |
|
|
Simer 3305P Convertible Jet Pump, 1/2HP
Simer Convertible Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 1/2HP 115V only, 1-1/4”NPT Suction x 1”NPT Discharge Ports, for Shallow Wells to 25 Feet or Deep Wells to 70 Feet, from 5.3GPM to 9.0GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, Built-in Pressure Regulator, Requires Jet Kit
|
516.00 |
|
|
SIMER 171P5620 CAPACITOR
For Simer Shallow Well Jet Pump Models 2800, 2800E, 2802, 2802E, 2803 use capacitor 171P5620.
This is a 30uf Capacitor.
Simer, Flotec and Sta-Rite parts are interchangeable. The Brand name does not matter, only the part number.
|
19.55 |
|
|
Flotec FP4855 Shallow Well Jet Kit
Ejector Jet Package converts FP4200 series convertible jet pumps for use with shallow well
|
103.74 |
|
|
Flotec FP4875 Shallow Well Jet Kit
Use on FP4300 series Flotec convertible jet pump
Bolts to nose of pump to convert for shallow well use
|
147.42 |
|
|
Simer 2961 Submersible Sewage Pump, Pitmaster, 4/10HP
Simer Submersible Sewage Pump, Thermoplastic Construction, Pitmaster, 4/10HP 115Volt Continuous Duty Motor, 2” NPT Discharge Port, up to 3900 GPH, 8 Foot Power Cord, Automatic or Manual Operation, Tethered Float Switch
|
456.00 |
|