|
Primer Bulb - 5/16" Inner Diameter Hose
This Atwood Primer Bulb is engineered and constructed to deliver the most reliable priming and long-term leak-free performance. The exclusive three-layer construction prevents collapse under vacuum and prevents ballooning or bursting under pressure. The low-permeation material prevents fuel evaporation, and this bulb delivers 60 percent more output per pump than leading competitors.
Features:
It is intended for use with a 5/16-inch interior diameter hose
Exclusive high-efficiency check-valves deliver faster priming and low fuel restriction (less than 1kPa restriction at 50 liters/hour)
Engineered hose barbs and stainless steel stepless clamps ensure leak-free performance
This bulb is compatible with Ethanol blended fuels, and it is EPA and CARB certified
|
18.89 |
|
|
Primer Bulb - 3/8" Inner Diameter Hose
This Atwood Primer Bulb is engineered and constructed to deliver the most reliable priming and long-term leak-free performance. The exclusive three-layer construction prevents collapse under vacuum and prevents ballooning or bursting under pressure. The low-permeation material prevents fuel evaporation, and this bulb delivers 60 percent more output per pump than leading competitors.
Features:
It is intended for use with a 3/8-inch interior diameter hose
Exclusive high-efficiency check-valves deliver faster priming and low fuel restriction (less than 1kPa restriction at 50 liters/hour)
Engineered hose barbs and stainless steel stepless clamps ensure leak-free performance
This bulb is compatible with Ethanol blended fuels, and it is EPA and CARB certified
|
18.89 |
|
|
Primer Bulb - 1/4" Inner Diameter Hose
This Atwood Primer Bulb is engineered and constructed to deliver the most reliable priming and long-term leak-free performance. The exclusive three-layer construction prevents collapse under vacuum and prevents ballooning or bursting under pressure. The low-permeation material prevents fuel evaporation, and this bulb delivers 60 percent more output per pump than leading competitors.
Features:
It is intended for use with a 1/4-inch interior diameter hose
Exclusive high-efficiency check-valves deliver faster priming and low fuel restriction (less than 1kPa restriction at 50 liters/hour)
Engineered hose barbs and stainless steel stepless clamps ensure leak-free performance
This bulb is compatible with Ethanol blended fuels, and it is EPA and CARB certified
|
19.30 |
|
|
Sierra Marine Engine Parts & Drive Parts
Sierra Marine is a trusted name in aftermarket replacement boat engine and drive parts. Sierra’s products are designed and engineered to exceed the high horsepower demands of today’s engines in the harshest marine environments. All Sierra products meet or exceed the original equipment part it replaces.
If you need help finding a part, we need, Make, Model, Year, Horsepower, and Serial number of your engine.
Warning: We can no longer ship engine parts International or to California Due to Prop 65.
|
|
|
Johnson/Evinrude/OMC (Outboard Marine Corporation) Female Hose Fitting - Tank Or Engine End - 5/16" Barb
For use on both ends of the fuel line to connect tank fitting and motor. The hose barb fits a 5/16" inner diameter hose.
Features:
Johnson, Evinrude, and OMC fitting
Tank or Engine End
Material Construction: Acetal
*Specifically mates to Attwood part number: 8883-6
|
5.69 |
|
|
Stainless Steel Thru-Hull Standard Straight Barbed - 5/8" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Standard Thread model has a full-length thread for thick hulls and easy tightening
Specifications:
Hose size: (inch) 5/8" inner diameter
Flange Diameter: (inch) 1-7/8"
Thread O.D. (outside diameter): (inch) 1"
Thread Length: (inch) 2"
Barb Length: (inch) 1-1/4"
Total Length: (inch) 3-3/4"
Install Hole Saw Size: (inch) 1-1/8"
Thread NPSM: (inch) 3/4"
Max Hull Thickness: (inch) 1-1/16"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
20.86 |
|
|
Stainless Steel Thru-Hull Short Straight Barbed - 5/8" Inner Diameter
Polish your image with these beautiful, durable stainless steel fittings. Why specify plastic parts when these fittings will last the life of the boat?
Rugged Stainless Construction:
Cast from certified Enhanced 316 Stainless Steel alloy for strength and lifetime corrosion-resistance
All visible areas are polished to a mirror finish, then passivate each part for additional protection
Thick steel sidewalls withstand continual stress and hose flexing
Faster, Simpler Installation:
Each Thru-Hull is available with a new silicone gasket
A channel under the flange holds a bead of sealant, making it easier to apply a trouble-free seal
All models have wrench flats or an end notch to hold as a gripping surface; one installer can tighten all connections from inside the hull
The barbed tail ends provide plenty of room to hold multiple clamps
Stainless Steel Straight Thru-Hulls, Barbed
Short Thread is a more compact size, which allows installation near corners and in confined areas
Specifications:
Hose size: (inch) 5/8" inner diameter
Flange Diameter: (inch) 1-7/8"
Thread O.D. (outside diameter): (inch) 1"
Thread Length: (inch) 1"
Barb Length: (inch) 1"
Total Length: (inch) 2-1/4"
Install Hole Saw Size: (inch) 1-1/8"
Thread NPSM: (inch) 3/4"
Max Hull Thickness: (inch) 5/8"
*Stainless Steel Thru-Hull Connectors are designed for installation above the water line only
|
18.25 |
|
|
Johnson/Evinrude/OMC (Outboard Marine Corporation) Female Hose Fitting - Tank Or Engine End - 3/8" Barb
For use on both ends of the fuel line to connect tank fitting and motor. The hose barb fits a 5/16" inner diameter hose.
Features:
Johnson, Evinrude, and OMC fitting
Tank or Engine End
Material Construction: Acetal
*Specifically mates to Attwood part number: 8883-6
|
4.64 |
|
|
White Plastic Thru-Hull Fitting - 5/8" Inner Diameter
This thru-hull fitting is made with a durable, thermoplastic construction, which prevents electrolysis.
Specifications:
Hose Size: (inch) 5/8" Inner diameter
Stem Length: (inch) 3-1/4"
Max Hull Thickness: (inch) 1-1/4"
Flange Diameter: (inch) 1-3/4"
Installation Hole Size: (inch) 1-1/8"
Drain Plug: (inch) 5/8"
Construction: Polypropylene
Color: White
*Plastic thru-hull connectors are designed for installation above the water line only
|
4.73 |
|
|
V-Cleat Open - Medium - 4-8mm(3/16" - 5/16") Rope Diameter
V-Cleats are a simple solution to cleating lines under moderate loads.
Features:
Lightweight and corrosion proof
Greater abrasion resistance than traditional plastic cleats
Low, snag free profile
Base profile suits mounting on flat and curved surfaces
Applications:
Control lines on dinghies and catamarans
Material:
PTFE impregnated, glass and carbon fiber composite cleats
|
9.58 |
|
|
V-Cleat Fairlead - Medium - 4-8mm(3/16" - 5/16") Rope Diameter
V-Cleats are a simple solution to cleating lines under moderate loads. Cut away in base of fairlead cleats can be used as a becket for a 2:1 purchase system.
Features:
Lightweight and corrosion proof
Greater abrasion resistance than traditional plastic cleats
Low, snag free profile
Base profile suits mounting on flat and curved surfaces
Applications:
Control lines on dinghies and catamarans
Material:
PTFE impregnated, glass and carbon fiber composite cleats
|
10.45 |
|
|
Sailmaker Stainless Steel Thimble - 8mm(5/16") Cable Diameter
Used to create eyes in both rope and wire rope
|
13.75 |
|
|
Swivel Cleat Fairlead - 2-8mm(3/32-5/16") Rope Diameter
Swivel cleat bases permit easy cleating and releasing from any angle.Dead eyes contain stainless steel liners for low friction and long life. Cleating plates are heavy guage alloy for stiffness and minimum distortion under load.
Features:
360° Rotation
Small T-Cleat & Fairlead
Applications:
Sheet leads and halyards on dinghies and catamarans
Materials:
Alloy cleating arms
Grade 316 Stainless Steel fittings
|
50.53 |
|
|
Neoprene Impeller Kit with Cover, Gasket or O-Ring - 6-Blade - 5/16 Shaft Diameter
Jabsco's Neoprene Impeller Kit is used specifically in Jabsco's Water Puppy, Part #6617.
Included:
Cover
Gasket
O-Ring
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
26.14 |
|
|
Universal Fuel Line Kit - 5/16" Diameter x 6' Length
This EPA-certified Attwood Universal Fuel Line Kit reliably delivers fuel to your engine and provides the ultimate in performance, safety, and value. The kit includes a 6-foot-long, 5/16-inch diameter low-permeation fuel line that is designed to prevent kinking and hardening, and is rated up to 100 degrees C. There’s also a multi-layer, low-permeation primer bulb with connections engineered for strength, durability, and leak resistance.
Features:
This Fuel Line Kit is compatible with Ethanol blended fuels and with all OEM-brand engines.
Universal for any engines and tanks
Multi-Layer, Low-Permeation Primer Bulb
6 ft. x 5/16 in. Low Permeation Hose
Reliably delivers fuel to your engine
*No end fittings included
|
41.39 |
|