Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Shields Multflex Hose has a clear FDA formula PVC with black vinyl helix. It is abrasion resistant, flexible and resistant to mild chemicals and salt water. Primarily used for bilge pump discharge, potable water tank fill and drains. Uses 147 right hand thread cuffs. Do not attach to thru hull fitting below the water line. Do not use ethylene glycol based antifreeze in hose.

2" Bronze Pedestal Pump Flow rate: Nominal 60 gallons/min at 1500 rpm Self-priming from dry up to 7.8ft Features: Constructed from marine quality bronze and stainless steel for ruggedness and reliability. Easy to service and maintain. Inexpensive to buy and operate. Will tolerate abrasive wear (this may affect performance - seek advice from your distributor). Handles hard and soft solids without clogging. Can pump in either direction. Will not airlock. APPLICATIONS MARINE: Engine cooling, pumping bilges, wash downs, circulating water in bait tanks, utility dock side pump. INDUSTRIAL: Circulating and transferring, Velocity-mixing, Return spill, Sump drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Inks, Dyes, Alcohol, Tanning Liquors, Glycerin, Brine, etc. FARMING: Pumping water for stock, Pumping water from shallow wells and cisterns. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer, and LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Sternflex 2" rigging hose used to cover harness and bracket mounted hoses on outboard engines. Polyethylene co-polymer wall with an integral polyethylene helix. Resistant to abrasion, crushing and UV. 3" bend radius.

For venting of bilge gases. Ozone & sunlight resistant. Will not support a flame. Black wire vinyl coated. 50 ft. rolls are sold by 50 ft. roll, but priced by the foot.

For venting of bilge gases. Ozone & sunlight resistant. Will not support a flame. Black wire vinyl coated. 50 ft. rolls are sold by 50 ft. roll, but priced by the foot.

4 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.

4 Blade stainless propeller for Mercury 90+ horsepower outboard engines, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower engines. All with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.

4 Blade stainless propeller for 150-300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

3 Blade aluminum propeller for Honda 75-130 horsepower engines and Nissan/Tohatsu 60-90 horsepower engines. Both with 15 tooth spline and thru hub exhaust. 4-1/4" gearcase.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.