4 Position Battery Terminal - POS/NEG The V-BATT-TML is a four-position battery terminal that can accept up to (2) 1/0 AWG and (2) 4 AWG, down to (4) 10 AWG wires.  It includes all markers and hardware to be used for the positive or negative post.  Features: Four (4) Outputs - (2) 1/0 AWG – 10 AWG plus (2) 4 AWG – 10 AWG  Compact design for simpler installation Solid brass construction for maximum conductivity Nickel finish for durability Positive and Negative marker plates included Negative post sleeve included In the Box: Brass battery terminal Negative post sleeve (pre-installed) Black "negative" marker plate (pre-installed) Red "positive" marker plate Two 10mm hex-socket screws 2 Rubber hole-caps 4mm Allen key 1.5mm Allen key *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

8 Position Battery Terminal - POS/NEG The VBTPN is an eight-position battery terminal that can accept up to (4) 4/8/10 AWG set screw outputs and (4) 1/0 to 10  AWG ring terminal outputs.  It includes (1) positive and (1) negative bolt-on posts for retaining the factory vehicle terminal. Features: Compact design for simpler installation Solid brass construction for maximum conductivity Nickel finish  Gate Lock Technology In the Box: Positive and Negative post Adapter sleeve T20 Torx® screws *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

8264 Traditional Metal DC Panel - 24 Positions Features: All positive, negative and grounding buses installed, fully pre-wired Panels with meters include toggle switch for mounting up to 3 battery banks All panels with analog meters are owner upgradable to 24 Volts with 8240 or 8243 (18-32V DC meters) All circuit label positions are backlit on standard panels - No kit required "ON" indicating LEDs installed in all circuit positions Specifications: Positions: 24 Nominal Voltage: 12 VDC/24 VDC Maximum Amperage: 100A per bus Height: 7.50" (190.5 mm) Width: 14.75" (374.65 mm) Weight: 7.45lb. (3.38 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

      Sprayway manufactures a complete line of industrial MRO, automotive, screen print and housekeeping products since 1947. Sprayway has been an innovative industry leader, and its Sprayway Glass Cleaner is recognized as "The World's Best." From marine detailing to industrial maintenance, whether it is a detailing wax or an industrial lubricant, Sprayway provides wide-ranging industries with the products they need.     The World's Best Glass Cleaner - Excellent for windows, mirrors, windshields and other glass surfaces! For cleaning and polishing glass, mirrors, windshields and windows. This easy-to use, fast acting product uses a clinging foam to break up soils and hold them - even on vertical surfaces. There is no dripping, no running and no streaking. With an exclusive formulation using denatured alcohol and no ammonia, this product cleans thoroughly, dries quickly, requires no rinsing and leaves a pleasant, fresh aroma.   SHOP: https://www.clrmarine.com/462m4/manufacturers/s/sprayway.html     Specials    Closeouts    Remanufactured    Rebates  

VR48 V10 Heavy Duty Set Screw Terminals - 4 AWG - 2 Pack You'll get tight and secure connections for your amplifier's power and ground cables with a set of T-Spec's set screw ring terminals.  You just insert the wire's stripped end and tighten the Torx T-20 set screw for a long-lasting and worry-free electrical connection. Features: One (1) Red and one (1) Blue marked terminal - 4 AWG  5/16" hole Nickel finish T20 Torx® screws Gate Lock technology In the Box: Two (2) 4 AWG wire terminals w/ set screws 2 Rubber insulators *Sold as 2 Pack WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Tinned Battery Terminal - 5/16" Stud - Negative Stud Size:5/16" Product Features: ANCOR Marine Grade™ lugs are manufactured from heavy duty annealed tinned brass, providing for maximum current flow 100% tin plated brass resists corrosion from salt and moisture Seamless barrel design allows for maximum strength when crimped Closed end design seals out moisture so cables stay dry and corrosion free WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Battery Terminal Covers - Red/Back - 1/2"  These Battery Terminal Covers are designed to insulate integral marine wing nut terminals protecting battery cables from corrosion and shorting. Constructed of injection molded PVC. These covers satisfy USCG and ABYC requirements for the prevention of accidental grounding of battery terminals. Color coded to avoid polarity misidentification. Will fit most marine batteries as well as automotive batteries using add on marine terminals. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Battery Terminal Covers - Red/Black - 5/8"  These Battery Terminal Covers are designed to insulate integral marine wing nut terminals protecting battery cables from corrosion and shorting. Constructed of injection molded PVC. These covers satisfy USCG and ABYC requirements for the prevention of accidental grounding of battery terminals. Color coded to avoid polarity misidentification. Will fit most marine batteries as well as automotive batteries using add on marine terminals. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

V10-D104K 4 Gauge Add-A-Amp Kit for 1/0 Gauge Wire If you've already installed a 1/0 AWG amplifier wiring kit in your boat, the T-Spec V10-D108K 4 AWG wiring kit will let you add another amplifier to your system.  This water-resistant kit includes everything you need to send power to your new marine amplifier. With 4 AWG wire, you'll get long life and maximum power transfer. This kit includes two brass distribution blocks, 10' power and ground wires, a 20' remote turn-on wire, installation hardware and wire ties for installation.  Does not include RCA cables or speaker wire. Features: Complete marine amplifier wiring kit Includes power wire, ground wire, turn-on wire, circuit breaker, ring terminals, wire ties, and more Marine-compliant cable In the Box: 4 AWG pearl White OFC copper wire - 10' 4 AWG matte Grey OFC copper wire - 10' 18 AWG Blue wire - 10' 2 Distribution blocks w/snap-on covers (One 1/0 AWG input to 4 AWG ouptut) Ten (10) 6" Wire ties Two (2) 4 AWG crimp-on spade terminals (non-insulated) One (1) 18 AWG crimp-on spade terminal (insulated) One (1) 18 AWG crimp-connector Four (4) 12 mm Phillips-head screws Two (2) Insulating boots for 4 AWG spade terminals Instruction sheet *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

DT Deutsch Receptacle Repair Kit - 14-18 AWG (4 Position) Pacer's DT repair kits use the larger size 16 contacts (Deutsch Pin P/N 0460-215-16141, Socket P/N 0462-209-16141) for applications using 14 AWG wires. However, DT series connectors are designed for 18-14 wire gauge applications. The DT series offers electrical designers the ability to use multiple sizes of 16 contacts (18-14 AWG) each with a 13-amp continuous capacity, within a single shell. Pacer also sells these other components for use in a wider range of applications. Features: Packs include all parts needed to assemble a connector One to two extra terminals Cavity plugs to seal open circuits Applications: Wire-to-wire applications Enclosed connectors offer field-proven reliability and rugged quality Compliances: Ingress Protection (IP) Level: IP68 and IP6K9K EU RoHS/ELV Standard UL-94 Recognized Characteristics: Wedge locks ensure contact alignment and retention Redundant Silicone Seals Hand-insertable and removable contacts Technical Specifications: Number of Cavities: 4 Housing: Rectangular receptacle, plastic reinforced with glass fiber Contact Size: 16 (13 amp) Wire Size: 14 AWG Holds Pin/Socket: Pins Operating Temperature: -55°C to 125°C Contents:  (1) 4 pos. receptacle (1) 4 pos. wedge lock (5) pins (2) cavity plugs

DT Deutsch Plug Repair Kit - 14-18 AWG (4 Position) Pacer's DT repair kits use the larger size 16 contacts (Deutsch Pin P/N 0460-215-16141, Socket P/N 0462-209-16141) for applications using 14 AWG wires. However, DT series connectors are designed for 20-14 wire gauge applications. The DT series offers electrical designers the ability to use multiple sizes of 16 contacts (20-14 AWG) each with a 13-amp continuous capacity, within a single shell. Pacer also sells these other components for use in a wider range of applications. Features: Packs include all parts needed to assemble a connector One to two extra terminals Cavity plugs to seal open circuits Applications: Wire-to-wire applications Enclosed connectors offer field-proven reliability and rugged quality Compliances: Ingress Protection (IP) Level: IP68 and IP6K9K EU RoHS/ELV Standard UL-94 Recognized Characteristics: Wedge locks ensure contact alignment and retention Redundant Silicone Seals Hand-insertable and removable contacts Technical Specifications: Number of Cavities: 4 Housing: Rectangular receptacle, plastic reinforced with glass fiber Contact Size: 16 (13 amp) Wire Size: 14 AWG Holds Pin/Socket: Sockets Operating Temperature: -55°C to 125°C Contents:  (1) 4 pos. plug (1) 4 pos. wedge lock (5) sockets  (2) cavity plugs

Lead Battery Terminal - 5/16" Stud - Negative Stud Size:5/16 " Product Features: ANCOR Marine Grade™ lugs are manufactured from heavy duty annealed tinned brass, providing for maximum current flow 100% tin plated brass resists corrosion from salt and moisture Seamless barrel design allows for maximum strength when crimped Closed end design seals out moisture so cables stay dry and corrosion free WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

NXL-M4 Full Range 4 Channel IPX5 Marine Grade Amplifier - 150 x 4W @ 4-Ohm Designed for intense sessions that keep the party boat rocking all night long; the NXL-M4 is DS18’s high-quality, powerful amplifier for the wave runner looking for a big sound with a small footprint! As a Class D Digital amplifier, the NXL-M4 uses a direct insert speaker and power terminals significantly smaller than your average amplifier, making it the perfect size for any vehicle’s custom build: but, what it lacks in size it makes up for in power. The NXL-M4 handles 150W x 4CH @ 4 Ohms; 230W x 4CH @ 2 Ohms; and 440W x 2CH @ 4 Ohms Bridge of RMS Power and 1800W Peak Power. Get clean, well-defined sound for with enough features (Fully Variable Bass Boost, Low Pass Filter, and High Pass Filter) to tune your music perfectly for optimal audio enjoyment! This full-range amplifier handles all speakers insanely well and has the features to make sure they play the way you want them to! This amplifier is tough enough to stand up to the worst the waves throw at you! All controls are guarded by high-strength front covers that guarantee impenetrable defense against the elements; coated 4-layer PCB helps prevent corrosion caused by salt water; and Voltage, Thermal, and Short Circuit Protection for easy monitoring of your power levels. Order the NXL-M4 for insane power out on the water! Features: Hardware resistant to corrosion and UV Protection Coated 4 Layers PCB to prevent corrosion IPX5 Water Resistance Grade High Level Input For Radio Use Front cover to keep the controls safe to the elements LED Clip Indicator to easier adjustment Stable and Reliable Class D Circuit Design Sound Quality Verification Using AP Instruments Direct Insert Power and Speaker Terminals Short Circuit, Thermal, and Voltage Protection Technical Specifications: Number of Channels - 4 Frequency Response - 20Hz - 20KHz  2 Ohm RMS Power Per Channel - 4 x 230W  4 Ohm RMS Power Per Channel - 4 x 150W  4 Ohm RMS Power Bridge Channel - 2 x 440W  Signal-to-Noise Ratio - >90dB  Product Dimensions: (L x W x H) - 9.6" x 4.5" x 1.7" *Sold as an Individual

3001 HD-Series Battery Switch Single Circuit ON/OFF with AFD Features: 600 Ampere Continuous Rating Accepts two 4/0 battery cables per terminal Ignition protected - safe for installation aboard gasoline powered boats .870" (22.01mm) stud length to accept multiple cable terminals 1/2" (M12) Tin-plated copper studs for maximum conductivity and corrosion resistance Meets American Boat and Yacht Council (ABYC) requirements for battery switches Tactile textures indicate knob position by feel only Case design allows surface or rear panel mounting Fits all Perko and Guest low amperage battery switch hole patterns WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

e-Series Selector 3 Position Battery Switch with AFD AFD: Yes Battery Combiner: No Features: Make-before-break contact design allows switching between battery banks without power interruption CE Marked Ignition protected-safe for installation aboard gasoline powered boats Case design allows surface or rear panel mounting Meets American Boat and Yacht Council (ABYC) requirements for battery switches 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals 7/8" (22.22mm) stud length to accept multiple cable terminals Tactile textures indicate knob position by feel only WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.