|
RAM Flex Adhesive Base w/1" Ball
Part #: RAP-B-378U
Consists of a 2.5" composite base that connects to a 1" ball, double-sided adhesive PSA stick pad and sealed alcohol prep pad. This base will attach to all RAM double socket arms that will accommodate 1" ball bases.
Material:
High Strength Composite
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag. A secondary tether is recommended when this mount is used in high vibration environments.
|
12.34 |
|
|
RAM Chrome Motorcycle Brake/Clutch Reservoir Base w/1" Ball
The RAM-B-309-1CHU connects to your handlebar clutch/brake clamp, left or right side, and holds one 1" diameter mounting ball. The chrome base fits the control clamps on your motorcycle with 40mm x 6mm stainless steel hardware, provided in the kit. To see if the RAM-B-309-1CHU base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
34.28 |
|
|
RAM 6.25" X 2" Rectangle Base with 1" Ball
The RAM-B-111BU consists 1" diameter rubber ball connected to a flat 6.25" x 2" rectangle base. The base contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more.
The RAM-B-111BU is compatible with the following electronic devices:
Garmin GPSMAP 162
Garmin GPSMAP 168
Garmin GPSMAP 175
Garmin GPSMAP 180
Garmin GPSMAP 180C
Garmin GPSMAP 182
Garmin GPSMAP 185
Garmin GPSMAP 188
Garmin GPSMAP 232
Garmin GPSMAP 238
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag. This plate is a universal mounting bracket with a selection of mounting hole locations. In certain applications additional holes may need to be drilled for proper fit with your electronic device.
|
13.99 |
|
|
RAM Motorcycle Brake/Clutch Reservoir Cover Base with 1" Ball Offset
The RAM-B-346U base fits cleanly over your existing brake/clutch reservoir cover with the 1" ball offset. Made of die cast aluminum with an over molded rubber ball, both form and function are unsurpassed. Installation is simple and all necessary hardware is included.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
19.54 |
|
|
RAM 2" x 2.25" Rectangle Base with 1" Ball
The RAM-B-202U-225 contains a 1" diameter rubber ball connected at right angles to a 2" x 2.5" rectangular base. This mount has pre-drilled holes at each corner of the base plate.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag. Mounting hardware not included with purchase.
|
13.33 |
|
|
Triple Magnetic 2.5" Round Base with 1" Ball
Consists of a 1" diameter rubber ball connected to a flat 2.5" diameter base and triple magnetic base adapter. The 2.5" diameter base contains pre-drilled holes, including the universal AMPS hole pattern. The magnetic base adapter contains 3 rare earth magnets that hold firm to ferrous metals. Simply put this product near the mounting surface and feel it almost jump out of your hand. The composite adapter designed to conceal the magnets is made of durable composite to prevent scratching the mounting surface. Ideally suited for many applications, you're sure to find many ways to use your magnetic mount at work, home, on the go, or at play.
|
21.70 |
|
|
RAM 1" Diameter Ball Mount with Short, Double Socket Arm, 2.5" Flex Adhesive Base & Diamond Base Adapter
The RAP-B-378-A-238U consists of the flex adhesive base with 1" ball, SHORT SIZE double socket arm and and diamond base adapter. The mount is designed with a 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The hole pattern found on the diamond base adapter will connect to most RAM cradles. The included RAM's patented design dampens shock and vibration, helping to extend the life of your device. Using a PSA stick pad, put the flex adhesive mount practically anywhere you want to keep your portable electronics easy to see and always within your reach. Designed with a very small foot print, finding a home on your scooter, motorcycle, kayak, boat or vehicle dash is easy. Attaching the patented 1" rubber ball, to one of many RAM arms, creates the ultimate socket system with multiple adjustment points for articulation and perfect viewing angles.
Material:
High Strength Composite
Ball Size
1" Rubber "B" Ball Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
22.73 |
|
|
RAM® X-Grip® Phone Mount with Flex Adhesive Base
The RAP-B-378-UN7U consists of the flex adhesive base with 1" ball, double socket arm and universal X-Grip® cradle. Using a PSA stick pad, put the flex adhesive mount practically anywhere you want to keep your portable electronics easy to see and always within your reach. Designed with a very small foot print, finding a home on your scooter, motorcycle, kayak, boat or vehicle dash is easy. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. The included X-Grip® cradle has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The spring loaded X-Grip® cradle expands and contracts, allowing for a perfect custom fit of your cell phone.
The X-Grip® includes a device tether recommended for outdoor applications. The cradle is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.
Hardware Included:
(1) Optional Tether
(1) Glue Tube for Rubber Caps
(1) 2.5" Double Sided Adhesive Disc
Holder Dimensions:
Width Range: 1.875" - 3.25"
Depth Range: .875" max
Socket-to-Socket Length:
3"
Ball/Socket Size:
B Size (1")
Weight Capacity:
2 lbs
|
45.91 |
|
|
RAM® Torque™ 3/8" - 5/8" Diameter Mini Rail Base w/ 1" Ball, Medium Arm and Diamond Ball Base
Take your mobile entertainment on the road with the new RAM® Torque™ handlebar and rail mounting base. We’ve paired a B-sized 1" ball base that accommodate bars 3/8" to 5/8” in diameter with a B-sized standard length arm and diamond base so that you can connect any of the RAM Mounts cradles or anything else with the AMPS hole pattern. Sizing inserts are included to provide a snug fit and offer additional protection for the rail. The mount utilizes nylon-insert locknuts to prevent loosening in high vibration environments. This low-profile mount is the perfect way to secure your personal electronics and small accessories in any high-vibration environment.
Mounting Base Dimensions:
Accommodates rails 3/8" to 5/8" in diameter
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag.
Weight:
0.56 lbs.
|
37.92 |
|
|
RAM 2" x 3" Rectangle Base w/1" Ball
The RAM-B-202U-23 contains a 1" diameter rubber ball connected at right angles to a 2" x 3" rectangular base. This mount has pre-drilled holes at each corner of the base plate.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag. Mounting hardware not included with purchase.
|
17.42 |
|
|
RAM 2" x 4" Rectangle Base w/1" Ball
The RAM-B-202U-24 contains a 1" diameter rubber ball connected at right angles to a 2" x 4" rectangular base. This mount has pre-drilled holes at each corner of the base plate.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag. Mounting hardware not included with purchase.
|
26.16 |
|
|
RAM 2" Max Width Square Rail Base with 1" Diameter Ball
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
22.44 |
|
|
RAM 3" Max Width Square Rail Base with 1" Diameter Ball
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1" Rubber Ball Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
34.32 |
|
|
RAM STACK-N-STOW Topside Base w/1" Ball
The RAP-395W-BBU consists of a 1" ball, connected to a round base, that contains female grooves and hardware that will allow mounting to all RAM STACK-N-STOW Bait Boards.
Material:
High Strength Composite
Ball Size:
1" Rubber Ball "B" Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
6.19 |
|
|
RAM Mount Composite Diamond Base w/1" Ball
Part #: RAP-B-238U
The RAP-B-238U, composite diamond base, contains a 1" diameter rubber ball connected at right angles to a 1.25" x 2.5" inch diamond plate. The base has two holes 1.912" from center to center, positioned at both ends of the diamond base.
Material:
High Strength Composite
Ball Size:
1" Rubber Ball "B" Size
|
5.71 |
|