Axle Tie Plate Kit f/1-3/4" Round Axle This kit has everything you need to mount fresh springs to a fresh axle. Includes: 2 galvanized tie plates 4 yellow zinc plated U-bolts 8 zinc plates nuts and lock washers

Axle Tie Plate Kit f/1-1/2" Square Axle This kit has everything you need to mount fresh springs to a fresh springs to a fresh axle. Includes: 2 galvanized tie plates 4 yellow zinc plated U-bolts 8 zinc plated nuts and lock washers

Axle Tie Plate Kit f/2" Square Axle This kit has everything you need to mount fresh springs to a fresh axle. Includes: 2 galvanized tie plates 4 yellow zinc plated U-bolts 8 zinc plated nuts and lock washers

Axel Tie Plate Kit for 3" Round Axel Everything needed to mount fresh springs to an axle.  Each Blister packaged kit includes:  2 galvanzied tie plates  4 yellow zinc plated u-bolts 8 zinc plated nuts Lock washers

1014 Downrigger Pulley Replacement Kit for 1" & 3/4" Booms Features: Intended for 1 in. and 3/4 in. booms Pulley replacement kit for Scotty Downriggers Includes a pulley wheel/housing, boom end cap, and adapters for all-sized booms

Double U-Bolt Bolster Bracket - 8-3/4" Mounting bunk boards using double U-bolt bolster brackets provides the most rigid bolt-on bracket mounting possible. Made from heavy 7 ga galvanized steel, these brackets are 4” wide with slots that are 1/2” wide spaced 1-3/4” apart with a top hole diameter of 1/2”.

Adjustable Mid Mount Rod Holder - 1.66" or 1-1/2" OD - White Powder Coat Aluminum with Sleeve & Hex Key C.E. Smith's line of white powder coated clamp-on rod holders offer a great alternative to stainless steel. These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Adjustable Mid Mount Fits rails with 1.66" or 1-1/2" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Adjustable Mid Mount Rod Holder - 1-1/4" or 1-5/16" OD - White Powder Coat Aluminum with Sleeve & Hex Key C.E. Smith's line of white powder coated clamp-on rod holders offer a great alternative to stainless steel. These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Adjustable Mid Mount Fits rails with 1-1/4" or 1-5/16" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Ampco Bi8202801-4.50, Bronze Impeller for KC2 1 3/4

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/4" SHAFT 2 3/4" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/4" SHAFT 3" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/4" SHAFT 2 1/2" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/4" SHAFT 3 1/4" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/4" SHAFT 3 1/2" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

C.E. Smith Company C. E. Smith Company, Inc. was established as a manufacturing firm producing precision metal stampings, fabrications and assemblies for a broad variety of industries. Stainless steel boating and fishing products are sold under the SMITH TM trademark. The line includes an adjustable, completely stainless steel t-top, fiberglass electronic boxes, t-top storage bags navigation lights and antenna bracket.