|
Raritan PHII PUMP Phii Pump Assy Complete
|
468.75 |
|
|
Great gift for Father's day, get dad what he really wants!
Learn how to brew beer at home even faster with a Homebrew Beer Pump, now 10% OFF!
Get Coupon Here
Buy your Homebrew Beer Pump Now!
|
|
|
Check all of your impellers contained within the engine cooling pumps, bilge pumps, ballast pumps, and so on. One of the biggest contributors to impeller deterioration and damage is sitting idle in the same position for several months, so a proper check of the impeller(s) is vital to a reliable operation of the boat after storage and/or no operation.
Replacing an impeller is a fairly easy and straightforward process and one that you have probably done in the past. It is important to use the right tool to remove an impeller from the pump. Channel lock or needle-nose pliers are fine, but using an impeller removal tool is the best choice. Never use a screwdriver to pry an impeller out of a pump; you could accidentally score the bronze housing which can lead to leaks. Make sure you know how the impeller is being held in place. Some are sealed to the shaft with an O-ring; others are held in place with a set screw and others with a c-clip.
Make sure to check the pump and the water lines for any trash or chunks of rubber that may have broken off from the impeller. Even the smallest blockage can cause major engine cooling and overheating issues. Also, remember to properly lubricate your new impeller with Vaseline or the lubricant included with the new impeller. This will reduce friction for a brand new impeller on a dry startup.
Most importantly, make sure you are using the right impeller for the application. We have seen many instances of people who have replaced an impeller with something that is close to the original, but not exactly right, and this can cause major problems for the engine once normal operation resumes. You cannot match the size of the used impeller to a new one to determine the replacement, as a used impeller can be swollen and disfigured from its original specifications. The best method is to obtain the impeller number off of the impeller itself, usually located on the edge of the shaft hole of the impeller, or obtain the part number of the pump, usually stamped into the bronze housing.
You can find just about every impeller that needs to be replaced at CLR Marine. We carry Sherwood, Jabsco and Globe just to mention a few. We also carry many of the miner and major rebuild kits for many pumps. A minor repair kit consists of the impeller and any gaskets or O-rings that may be needed to replace the impeller. Our major rebuild kits include everything to rebuild that pump except for the shaft. All kits are put together at time of order so you will always see the Quantity on Hand as 0.
|
|
|
Amt 5764-95 Sub Shredder Pump 3" Npt
SUBMERSIBLE SHREDDER SEWAGE PUMP
Cast Iron with Stainless Steel Motor Housing
Carbide-Tipped Shredder Impellers
Spiral Shredder Mechanism Plate Surface Hardened for Enhanced Cutting Ability
Silicon Carbide Lower Seal
3" NPT Port Sizes
Max. Temperature 104° F
3 HP
230 Volt
AMT Submersible Shredder Sewage pumps feature an enhanced spiral shredder mechanism plate and carbide tipped impeller to prevent clogging and reduce maintenance when cutting through stringy, fibrous and sludge type waste. Applications include sewage pumping stations, septic tanks, sewage treatment plants, dirty water drainage, flood and emergency. Also ideal for grinder type solids reduction application. Motors are rated continuous duty and single phase models have thermal overload protection.
AMT Submersible Shredder Sewage Pumps are reliable, cost effective and low maintenance.
|
1824.94 |
|
|
Flotec FPSE3601A Cast Iron Sewage Pump 1/2 HP
Rugged, sewage and effluent pumps are capable of handling solids up to 2". Available in cast iron design for a variety of wastewater applications.
Heavy-duty, rugged cast iron automatic submersible sewage pump
Capable of handling 2" solids - ideal for basement installations, pumping below grade toilets, laundry facilities, underground parking, grain storage and construction sites
Includes by-pass float switch for automatic or manual operation
BODY CONSTRUCTION: CAST IRON
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9000 GPH
FLOW AT 10' LIFT: 5400 GPH
SWITCH TYPE: Tethered
DISCHARGE PIPE SIZE: 2" NPT
MINIMUM PIPE SIZE: 2" for sewage applications / 1-1/2" for effluent applications
MAXIMUM SOLID HANDLING SIZE: 2"
CORD LENGTH: 10'
AMP DRAW: 13 amps
VOLTAGE: 115v. 60 Hz
RECOMMENDED BREAKER: 20 amp
|
699.00 |
|
|
Myers Pumps SRM4T 20 Sewage Pump 4/10Hp 115V 20'
The SRM4T 20 is made of cast iron and has an oil-filled motor for heat dissipation and continuous bearing lubrication. It is suitable for domestic wastewater septic pumping, large sumps, and residential septic tank sewage.
|
721.50 |
|
|
Flotec FPSE3200A Thermoplastic Sewage Pump
Durable, corrosion-resistant thermoplastic construction with 2" solids handling makes the FPSE3200A a great candidate for variety of wastewater applications.
Automatic submersible sewage pump
Capable of handling 2" solids - ideal for basement installations, pumping below grade toilets, laundry facilities, underground parking, grain storage and construction sites
Durable, corrosion-resistant thermoplastic construction
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 4/10
MAXIMUM CAPACITY: 5250 GPH
FLOW AT 10' LIFT: 2550 GPH
SWITCH TYPE: Tethered
SWITCH ON LEVEL: 12-1/2"
SWITCH OFF LEVEL: 5-1/2"
DISCHARGE PIPE SIZE: 2"
MINIMUM PIPE SIZE: 2" for sewage applications / 1-1/2" for effluent applications
MAXIMUM SOLID HANDLING SIZE: 2"
CORD LENGTH: 8'
AMP DRAW: 8.5 amps
VOLTAGE: 115v, 60 Hz
RECOMMENDED BREAKER: 15 amps
|
456.00 |
|
|
Oberdorfer 209M Series Macerator Pump
FEATURES
Pump Body:
Bronze
Ports:
Inlet: 2" Slip-on Hose and 1 1/2" Pipe Thread
Outlet: 3/4" Garden Hose and 3/8" Pipe Thread
Flow:
9.0 GPM Max
Pressure:
12 PSI Max
Impeller:
Flexible Rubber Impeller Neoprene standard, Buna Optional.
Shaft Seal:
Lip Seal
Shaft:
Stainless Steel Motor Shaft
Motor / Drive:
12, 24 or 32VDC high torque, 18 amps. Intermittent duty cycle. Do not run pump dry.
APPLICATIONS / CHARACTERISTICS
BRONZE CLOSE COUPLED RUBBER IMPELLER PUMP, SEWAGE - MACERATOR
Used in: Utility Trailers, Boats, Railroads, Buses, Motor Homes, Emergency, Campers, Mobil Homes, Cottages, Camp Sites, Aircraft, Marine Transporation, Recreational Vehicles, Land & Water Cruisers, Commercial & Pleasurecraft.
Will handle sewage, waste, toilet paper, cigarettes, cigars and all maceratable solids of approximately 1 inch size. Self priming up to 4 ft. Up to 20 ft. uphill discharge or up to 50 ft. away. (Use large diameter garden hose - 3/4” - for best results.) A 30 gallon holding tank can be emptied in less than 4 minutes. Motor Shaft Slinger Protects Motor Bearings. Rubber Motor Grommets for Noise Isolation. Macerator Wheel and Impeller Easily Replaced. Removable Base.
Oberdorfer Macerator Pump Head Only, Bronze
|
490.31 |
|
|
Oberdorfer 209M-17246 Bronze Pump W/24Vdc Motor
Oberdorfer 209M Series Macerator Pump
FEATURES
Pump Body:
Bronze
Ports:
Inlet: 2" Slip-on Hose and 1 1/2" Pipe Thread
Outlet: 3/4" Garden Hose and 3/8" Pipe Thread
Flow:
9.0 GPM Max
Pressure:
12 PSI Max
Impeller:
Flexible Rubber Impeller Neoprene standard, Buna Optional.
Shaft Seal:
Lip Seal
Shaft:
Stainless Steel Motor Shaft
Motor / Drive:
12, 24 or 32VDC high torque, 18 amps. Intermittent duty cycle. Do not run pump dry.
APPLICATIONS
BRONZE CLOSE COUPLED RUBBER IMPELLER PUMP, SEWAGE - MACERATOR
Used in: Utility Trailers, Boats, Railroads, Buses, Motor Homes, Emergency, Campers, Mobil Homes, Cottages, Camp Sites, Aircraft, Marine Transporation, Recreational Vehicles, Land & Water Cruisers, Commercial & Pleasurecraft.
Will handle sewage, waste, toilet paper, and all maceratable solids of approximately 1 inch size. Self priming up to 4 ft. Up to 20 ft. uphill discharge or up to 50 ft. away. (Use large diameter garden hose - 3/4” - for best results.) A 30 gallon holding tank can be emptied in less than 4 minutes. Motor Shaft Slinger Protects Motor Bearings. Rubber Motor Grommets for Noise Isolation. Macerator Wheel and Impeller Easily Replaced. Removable Base.
Oberdorfer Macerator Pump, Bronze, 24VDC Motor
|
872.35 |
|
|
Flotec FP400C Sewage Pump System - 4/10 HP
Economical sewage pump system manufactured of durable thermoplastic construction. Ideal for basement installations, pumping below-grade toilets, and laundry facilities.
KEY FEATURES
Maximum pumping capacities up to 5250 GPH
Corrosion-resistant construction with multi-vane, non-clog vortex impeller
Grommets accept 4" PVC inlet, 2" PVC discharge and vent
Handles up to 2" solids
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: thermoplastic pump / structural foam basin
HORSEPOWER: 4/10
MAXIMUM CAPACITY: 5250 GPH
FLOW AT 10' LIFT: 2550 GPH
SWITCH TYPE: Tethered
DISCHARGE PIPE SIZE: 2"
MINIMUM PIPE SIZE: 2"
MAXIMUM SOLID HANDLING SIZE: 2"
CORD LENGTH: 8'
AMP DRAW: 18.5 amps
VOLTAGE: 115v, 60 Hz
|
784.08 |
|
|
Myers Pumps CMV5A-11 Sewage Pump 1/2Hp 115V
Myers CMV5A-11 is a 1/2-horsepower, 115-volt sewage pump that is designed for demanding residential installations. It is made with a combination of cast iron and thermoplastic for corrosion resistance. It also has a recessed vortex impeller that can handle solids up to 2 inches in diameter.
|
684.13 |
|
|
Goulds WS0511B Sewage Pump
Goulds WS0511B Series Submersible Sewage Pump
1/2 HP, 1750 RPM
115 Volt, 60 Hz, Single Phase 14.5 Max Amps
Up To 185 GPM
5" Impeller
Up To 38' TDH Heads
2" NPT Discharge
14.5 Max Amps
2" Solids Handling
|
1166.26 |
|
|
Simer 2961 Submersible Sewage Pump, Pitmaster, 4/10HP
Simer Submersible Sewage Pump, Thermoplastic Construction, Pitmaster, 4/10HP 115Volt Continuous Duty Motor, 2” NPT Discharge Port, up to 3900 GPH, 8 Foot Power Cord, Automatic or Manual Operation, Tethered Float Switch
|
456.00 |
|
|
Simer 3963 Submersible Sewage Pump, Pitmaster, 1/2HP
Simer Submersible Sewage Pump, Cast Iron Construction, Pitmaster, 1/2HP 115Volt, 2” NPT Discharge Port, up to 9000 GPH, 10 Foot Power Cord, Automatic or Manual Operation, Tethered Float Switch
|
699.00 |
|
|
Oberdorfer 214M Series Macerator Pump
FEATURES
Pump Body:
Bronze
Ports:
Inlet: 1 1/2" Threaded
Outlet: 3/4" Garden Hose and 3/8" NPT
Flow:
12.5 GPM Max
Pressure:
30.0 PSI Max, 70 feet of head
Impeller:
Neoprene Standard, Buna Optional
Shaft Seal:
Lip Type
Shaft:
Stainless steel motor shaft
Motor / Drive:
High torque capacitor start 1/3 HP TEFC 115V motor with grounded 3 prong cord.
APPLICATIONS / CHARACTERISTICS
CLOSE COUPLED BRONZE MACERATOR RUBBER IMPELLER PUMP
For sewage transfer from toilets to holding tanks For pump-out and disposal from holding tanks. Will Handle sewage, waste, toilet paper, cigarettes, cigars, and all maceratable solids of approximately 1 inch size. A suction lift of up to 4 feet is possible under ideal conditions. Because the suction line for sewage handling is of large size (1 1/2” pipe) a large volume of air must be evacuated to create vacuum and suction lift. This is why a “wet” start is essential to prevent overheating and burning of the impeller during the air evacuation and suction period.
Oberdorfer Macerator Pump Head Only, Bronze
|
930.60 |
|