Raritan PHII PUMP Phii Pump Assy Complete

  Check all of your impellers contained within the engine cooling pumps, bilge pumps, ballast pumps, and so on.  One of the biggest contributors to impeller deterioration and damage is sitting idle in the same position for several months, so a proper check of the impeller(s) is vital to a reliable operation of the boat after storage and/or no operation.   Replacing an impeller is a fairly easy and straightforward process and one that you have probably done in the past. It is important to use the right tool to remove an impeller from the pump. Channel lock or needle-nose pliers are fine, but using an impeller removal tool is the best choice.  Never use a screwdriver to pry an impeller out of a pump; you could accidentally score the bronze housing which can lead to leaks.  Make sure you know how the impeller is being held in place.  Some are sealed to the shaft with an O-ring; others are held in place with a set screw and others with a c-clip.   Make sure to check the pump and the water lines for any trash or chunks of rubber that may have broken off from the impeller.  Even the smallest blockage can cause major engine cooling and overheating issues.  Also, remember to properly lubricate your new impeller with Vaseline or the lubricant included with the new impeller. This will reduce friction for a brand new impeller on a dry startup.   Most importantly, make sure you are using the right impeller for the application. We have seen many instances of people who have replaced an impeller with something that is close to the original, but not exactly right, and this can cause major problems for the engine once normal operation resumes.  You cannot match the size of the used impeller to a new one to determine the replacement, as a used impeller can be swollen and disfigured from its original specifications.  The best method is to obtain the impeller number off of the impeller itself, usually located on the edge of the shaft hole of the impeller, or obtain the part number of the pump, usually stamped into the bronze housing.   You can find just about every impeller that needs to be replaced at CLR Marine.  We carry Sherwood, Jabsco and Globe just to mention a few. We also carry many of the miner and major rebuild kits for many pumps.  A minor repair kit consists of the impeller and any gaskets or O-rings that may be needed to replace the impeller.  Our major rebuild kits include everything to rebuild that pump except for the shaft.  All kits are put together at time of order so you will always see the Quantity on Hand as 0.

General Pump WM4215C Reverse Osmosis Pump The WM Series Direct Drive Industrial Pressure Washer Pump or Reverse Osmosis Pump.   Hollow Shaft – General Pump WM Series Specs:   Reverse Osmosis Pump - Left Shaft Max. Inlet Pressure 50 PSI Max. Fluid Temperature 140 Degrees Fahrenheit Inlet Port Thread 1/2in. NPT/F Discharge Port Thread 3/8in. NPT/F Shaft Diameter 5/8in. Pump Dimensions 9.9in. x 7.5in. x 6.0in. Crankcase Oil Capacity 12 oz (use GP Series 100 Oil)     Hollow Shaft – General Pump WM Series Features: 316 stainless steel fluid end for superior corrosion protection. Solid ceramic plungers with advanced surface finish assure durability and longevity. Compact design offers solutions to space limitations. Parallel inlet and outlet valve design for efficiency and easy maintenance.  

General Pump WM4215CL Reverse Osmosis Pump The WM Series Direct Drive Industrial Pressure Washer Pump or Reverse Osmosis Pump. This General Pump WM4215CL has dual inlet and outlet porting. It features the following specs: right hand, 5/8" hollow shaft, 4.2 GPM, 1500 PSI, 1750 RPM   Product Description Reverse Osmosis Pump - Right Shaft This pump is from the General Pump WM Series. It is a reverse osmosis, hollow shaft pump with roller bearings. See Related Products for compatible pump oil. • 316 stainless steel wet-end • 300 Series stainless steel fasteners • Parallel inlet and outlet valve design for efficiency and easy maintenance • Corrosion resistant valve and packing design • Innovative wear resistant high and low-pressure seals • Dual inlet and outlet porting • Anodized crankcase for corrosion resistance • NEMA 56C flange with 5/8” hollow shaft   Technical Specifications Bore: 18 mmStroke: 12.5 mmC rankcase Capacity: 12 oz.Max Temperature: 140º F Inlet Port: 1/2"Shaft Diameter: 5/8"Max GPM: 4.2Max PSI: 1500 RPM: 1750

SHURflo 2088-643-144, Diaphragm Pump 3.2 GPM 12VDC SHURflo Diaphragm Pump Standard, 3.2 GPM Open Flow, 12VDC Intermittent Duty, Buna Valves, Santoprene Diaphragm, 45 PSI Demand Switch (adjustable 30-50 PSI), 1/2" MSPT Ports, Polypropylene Housing, General Purpose Industrial Pump

SHURflo 8020-503-250, Diaphragm Pump 3 Chamber 1.5 GPM 115VAC SHURflo Diaphragm Pump 3 Chamber, 1.5 GPM Open Flow, 115VAC Intermittent Duty, 45 PSI Bypass (no switch), Viton Valves, Santoprene Diaphragm, Polypropylene Housing, 3/8" NPT Female Ports, Has a Power Cord, General Industrial Pump.

Shurflo 8020-513-236 Pump 115V 60Sw Pvs Shurflo- Diaphragm Pump 3 Chamber, 1.5 GPM Open Flow, 115VAC Intermittent Duty, 60 PSI Demand Switch (adjustable 40-60 PSI), Viton Valves, Santoprene Diaphragm, Polypropylene Housing, 3/8" NPT Female Ports, Has a Power Cord, UL/CSA Recognized, General Industrial Pump

Roper Pump 18AM08 Pump Flange Mounted W/Relief Roper A Series Gear Pump, model 18AM08 Housing : Cast Iron Gears : Ductile Iron Bearings : Bronze Idler Shafts : Ductile Iron Drive Shafts : Hardened Steel This is a general purpose Roper A series Pump for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer. The Roper A Series pumps are adaptable to a wide range of applications pumping clean fluids, such as pressure lubrication, hydraulic service, fuel supply or general liquid transfer. These pumps are designed to operate at standard motor speeds, with provisions for flange or foot mounting.  

General Pump 650021 Slinger Brass General Pump 650021 is a replacement slinger for WM Series reverse osmosis pumps.

General Pump 650048 Gasket Rear Cover General Pump 650048 is a gasket for the rear cover on WM Series pumps. Compatible with models WM0515C, WM0815C, WM1015C, WM1615C, WM2315C, WM2415CL, WM3015C, WM3615C, WM4215C, WM2315C, WM3015C, and WM4215C.

General Pump WM02 Seal Kit Packing kit for standard General Pump WM series pumps including the WM0515C, WM0815C, WM1015C, WM1615C, WM2315C, WM2415CL, WM3015C, WM3615C, and WM4215C models. OEM replacement parts, guaranteed to fit. Use to repack pump during maintenance or repairs.   Includes: 66024, Anti-extrusion Ring (3) 701051, O-Ring, 70D (3) 90220000, Low Pressure Seal (3) 520376, Low Pressure Case Seal (3) 710010, Glyd Case, 18mm (3) 710011, Square Seal, 18mm (3) 520375, Seal Retainer (3) 701023, O-Ring (3)

MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 15 Part #: MP21381 Size: 3 in. NPT Flow-Rate: 320 GPM Head Feet: 145   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

General Pump 701133 O Ring Buna Made of Buna-N with a 70 Duro hardness.   Compatible Pumps: T Series 69 T41 CW Series 69 CW1012 WM Series WM0515C WM0815C WM1015C WM1615C WM2315C WM2415CL WM2315C WM3015C WM4215C WM3015C WM3615C WM4215C WM2315C WM3015C WM3615C WM4215C WM2515S WM4215S

General Pump 100295 Oil 30W 16 Oz 30W viscosity, non-detergent. Special anti-scuff and anti-wear agents extend the lives of gear, vane, radial piston, and plunger pumps. Resists formation of harmful oil water emulsions Exceeds wear prevention requirements of all major. One Pint Bottles.

Jabsco 12210-0003 Pump 115V Motor Pump Body: Bronze Port Size: 3/8" NPT Internal Pipe Thread and Adaptors for 3/4" garden hose thread Flow: 3.4 GPM at 10ft Pressure: 17.4 PSI Max Impeller: Neoprene or Nitrile Shaft Seal: Lip Type Motor: 115 Volt AC Intermittent duty with Replaceable Brushes, Stainless Steel Shaft, 6' cord, three prong grounding plug   APPLICATIONS The 12210-Series Pumps are the most compact self-priming flexible impeller 115 Volt AC Utility Pumps Jabsco offers.   INDUSTRIAL: Transferring liquids. Velocity-mixing. Pumping coolants. Pumping waste water to sewer. Cellar, yard and sump drainage. Cooling Heliarc welding equipment.   MARINE: Washing down decks and docks. Water for ship's service supply. Pumping out crank-case oil.   FARMING: Pumping water for stock, poultry houses, farmhouse. Pumping water from wells and cisterns. Pumping liquid ballast into tractor tires. Pumping water from flooded basements.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, cesspools, sumps, etc. Draining water heaters and water closets. Draining laundry tubs below sewer level. Removing water trapped between walls, draining inaccessible places when pipes break or leak. Draining fishing ponds and garden pools. Removing sludge, lye water and other caustics from stopped up drains and sinks.   Jabsco Flexible Impeller Utility Pump 115V 3.4GPM Nitrile Impeller