|
Long Hose Trim - 3-1/2" with Screws
Hose trim is used for appearance and to conceal the hole that is drilled for the hydraulic hose to pass through the transom.
Features:
3-1/2 inches
Resist ultraviolet rays and are made of impact-resistant nylon or glass-filled, thus eliminating expansion from hydraulic pressure and water absorption
Hose trim comes with four black xylon-coated screws
|
13.50 |
|
|
Impeller Kit - 9 Blade - Nitrile - 3-3/4" Diameter x 3-1/2" W, 1" Shaft Diameter
Features:
Material: Nitrile
Drive Type: Spline Drive
Number of Blades: 9
Dimensions: Diameter: 3-3/4", Shaft Diameter: 1", Shaft Width: 3-1/2"
Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.
Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.
Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.
Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.
Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such.
Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
189.23 |
|
|
Leveler Short Hose Trim - 2-1/2" with Screws
Hose trim is used for appearance and to conceal the hole that is drilled for the hydraulic hose to pass through the transom.
Features:
2-1/2 inches
Resist ultraviolet rays and are made of impact-resistant nylon or glass-filled, thus eliminating expansion from hydraulic pressure and water absorption
Hose trim comes with four black xylon-coated screws
|
13.50 |
|
|
March MDX-3 1/2" Ports Pump W/115V Mtr
|
281.78 |
|
|
Applications for the MDX-3-1/2 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.
March Pump's industrial MDX-3-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8 gallons per minute at 1 foot, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, carbon filled Kynar (PVDF), Ryton Buna N, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheitor 87 Celsius. The March MDX-3-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
8.5 GPM
30 LPM
Max Head
19 FT
4 M
Power
.04 HP
.029 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1/2"OD
Outlet
1/2"OD
Wet End
Polypropylene (Front Housing and Impeller), Carbon filled Kynar (Rear Housing, Shaft), Ryton (Thrust Washer), Buna N (O-Ring), Stainless Steel (Screw) Ceramic Magnet
|
328.58 |
|
|
SuproFlex Rub Rail Kit - Black with Flex Chrome Insert - 2"H x 1.2"W x 60'L
The SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes.
Features:
Ideal for boats up to 65'
Co-extruded to provide two levels of hardness
Rigid backing and soft durometer front
Shock-absorbing channels for higher impact resistance
Lighter weight than traditional vinyl rub rail
Requires no pre-forming and minimal heating
Pairs with V12-0307CP (included in kit)
Made in the USA
5-year limited warranty
|
554.51 |
|
|
SuproFlex Rub Rail Kit - Black with Flex Chrome Insert - 2"H x 1.2"W x 80'L
The SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes.
Features:
Ideal for boats up to 65'
Co-extruded to provide two levels of hardness
Rigid backing and soft durometer front
Shock-absorbing channels for higher impact resistance
Lighter weight than traditional vinyl rub rail
Requires no pre-forming and minimal heating
Pairs with V12-0307CP (included in kit)
Made in the USA
5-year limited warranty
|
693.35 |
|
|
SuproFlex Rub Rail Kit - White with Flex Chrome Insert - 2"H x 1.2"W x 60'L
The SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes.
Features:
Ideal for boats up to 65'
Co-extruded to provide two levels of hardness
Rigid backing and soft durometer front
Shock-absorbing channels for higher impact resistance
Lighter weight than traditional vinyl rub rail
Requires no pre-forming and minimal heating
Pairs with V12-0307CP (included in kit)
Made in the USA
5-year limited warranty
|
610.32 |
|
|
SuproFlex Rub Rail Kit Gray with Gray Insert - 2"H x 1.2"W x 80'L
The SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes.
Features:
Ideal for boats up to 65'
Co-extruded to provide two levels of hardness
Rigid backing and soft durometer front
Shock-absorbing channels for higher impact resistance
Lighter weight than traditional vinyl rub rail
Requires no pre-forming and minimal heating
Predrilled for fasteners
Pairs with V12-0307GRD gray insert (included in the kit)
Made in the USA
5-year limited warranty
|
769.79 |
|
|
PSS Shaft Seal Maintenance & Parts Replacement Kit
FOR 2" SHAFT 3 1/2" TUBE
As with any rubber hose below waterline, the PSS bellows must be inspected
on a regular basis for any sign of wear, aging or chemical deterioration.
The PSS bellow should be replaced in six year intervals. During bellows
replacement it is recommended the o-rings & set screws in the stainless
steel rotor also be replaced.
Bellows may need to be more frequently inspected in an environment where
non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate
rubber deterioration, as will an ozonater.
The Maintenance Kit includes the items you need to properly maintain your
PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings,
five (5) set screws, four (4) new hose clamps and an allen key.
|
137.26 |
|
|
Ampco Pumps P1GXPIP-1/2 Plastic Cap Plug
|
3.65 |
|
|
Ampco Pumps KC2 2 1/2 X 2 Fluid End Nialbz 5.00" Trim
|
3440.34 |
|
|
Detroit Diesel 671Ti-871-1271 Pump W/ 3 1/2" Splined Imp
|
3982.60 |
|
|
Shackle Bolts & Lock Nuts - 3-1/2"
Use with heavy duty 9/16" eye springs and spring hanger brackets.
Fluted shank prevents the bolt from turning in the bracket, preventing bracket wear. Sold in pairs.
|
10.42 |
|
|
PSS Shaft Seal Maintenance & Parts Replacement Kit
FOR 1 3/4" SHAFT 3 1/2" TUBE
As with any rubber hose below waterline, the PSS bellows must be inspected
on a regular basis for any sign of wear, aging or chemical deterioration.
The PSS bellow should be replaced in six year intervals. During bellows
replacement it is recommended the o-rings & set screws in the stainless
steel rotor also be replaced.
Bellows may need to be more frequently inspected in an environment where
non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate
rubber deterioration, as will an ozonater.
The Maintenance Kit includes the items you need to properly maintain your
PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings,
five (5) set screws, four (4) new hose clamps and an allen key.
|
137.26 |
|