|
Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
Cylinder is 7 1/2 inches eye to eye when closed.
|
126.00 |
|
|
As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away.
Outside Storage?
It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.
Rinse/Flush
Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat.
Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring.
Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present.
Salt
Watch out for salt. Buy a good salt remover to minimize corrosion.
Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine.
Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4*
STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel.
Batteries
Remove the batteries from your boat and store in your garage or basement.
Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery.
If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat.
Cleaning
Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint.
Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins.
Cover Up
If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often.
https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html
and
https://www.clrmarine.com/462m4/winterizing.html
Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information.
Fair winds and smooth sailing.
To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/.
_________________________________________________________________________
Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten.
She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com
©Copyright Cheryl Kuba, 3happycampers.com, 2021.
|
|
|
UC95OBF-1 Hydraulic Cylinder 175HP or Less
Intended for single engine applications of 175 HP and under, the UC95 OBF-1 cylinder is compatible with competing helms, hoses, and oil, and is built to last with heavy-duty stainless steel cylinder rods, seals, and link assemblies.
Features:
Balanced the number of turns lock-to-lock is the equal port to starboard or vice-versa
Adjustable boss style fittings for easy installation High resistance stainless steel connection bolt (ULTRABOLT)
Constructed of top-grade materials this cylinder is simple to install and fits almost every two and four-stroke outboard engine on the market our engine
Split and pinned mounting rod for easy installation and bushings to prevent friction with engine
|
518.17 |
|
|
UC128 Version 1 Hydraulic Cylinder - Port
The UC128TS-1P is the Port version of the Protech Front Mount Steering Cylinder. It is used along with the standard cylinder in high horsepower dual engine applications. It shares all of the innovation and attributes of the standard Protech cylinder. Durability and performance define the Protech Front Mount Outboard Steering Cylinders.
Features:
The replaceable triple sealed 1 3/4" cylinder end cartridges offer industry-leading longevity and durability
Designed for up to 600HP in certain applications
304 electropolished and passivated link assembly for peak corrosion resistance
Carbon-steel piston allows less internal bypass and provides greater efficiency
Ultrabolt high-strength stainless steel tiller bolt
|
670.25 |
|
|
UC128 Version 1 Hydraulic Cylinder
Compatible with competing helms, hoses, and oil, the UC128 cylinder is built to last with heavy-duty stainless steel cylinder rods, seals, and link assemblies. Constructed of top-grade materials this cylinder is simple to install and fits almost every two and four-stroke outboard engine in the market.
Balanced: The number of turns lock-to-lock is equal port to starboard or vice-versa. High resistance stainless steel connection bolt.
Volume: 120cc: 7.3 cu. in
Output Force: 450 kg - 992 lbs
Inside Diameter: 35mm - 1.37"
Stroke: 185mm - 7.28"
3/8" (9,5 mm fittings) - For high pressure flex hose
Bleed Fittings: DN5 Quick connect
|
670.25 |
|
|
UC128TS Version 2 Hydraulic Cylinder 1.38" Bore 7.8" Stroke Front #2 Link Arm Front Mount
Features:
The replaceable triple-sealed 1 3/4" cylinder end cartridges offer industry-leading longevity and durability
Designed for up to 600HP in certain applications
304 electropolished and passivated link assembly for peak corrosion resistance
Carbon-steel piston allows less internal bypass and provides greater efficiency
Ultrabolt high-strength stainless steel tiller bolt
Specifications:
Application: Outboard
Dimensions: 3"H x 6"D x 27"L
Horsepower: Up to 300 Horsepower
|
670.25 |
|
|
Boat Outfitting Equipment and Supplies
When it comes time for outfitting your boat, you can get all your boating supplies and boating accessories from us. You will never need to go anywhere else for your boat outfitting, because we have all the boat supplies you need. If you're looking for anchors/chain/rope, anodes, antifouling systems or boarding ladders, we have you covered. We can also offer you a selection of bottom paint and bow thrusters to choose from. You may also want cleaning supplies that offer deck/galley options so you can get your boat sparkling and ready to enjoy. We also have display mounts and docking accessories to complete your outfitting needs.
|
|
|
Boat Leveler to Bennett Actuator Conversion Kit - Hydraulic to Hydraulic
Bennett Marine's V351CK conversion kit replaces Boat Leveler cylinders with Bennett though-hull fittings.
Kit includes:
2 hydraulic cylinders and all hardware to convert your system
2 stainless steel conversion brackets
8 1/4-20 x 1/2 machine screws
4 1/4-20 x 3/4 wood screws
2 3" pipe nipples
2 female barb fittings
2 actuators
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
212.60 |
|
|
Insta-Trim boat leveler's electronic tab locator shows the
position of your tabs. Two seperate lines of diode lamps
accurately indicate the position of each tab. the screen is
small, mounts on the dashboard, and is designed to
match your rocker type controls in size and appearance.
The detectors are rugged and attach easily and quickly to
each hydraulic cylinder. The attached readout line runs
up to the light panel with simple plug in connections.
Insta-Trim electonic tab locators can be added to your
existing boat leveler system, upgrading your system for a
better, more accurate performance.
Installation is quick, easy, and simple. Only a few
common tools are rquired, and the tab locators come
with easy to follow instructions.
|
364.50 |
|
|
Insta-Trim boat leveler's electronic tab locator shows the
position of your tabs. Two seperate lines of diode lamps
accurately indicate the position of each tab. the screen is
small, mounts on the dashboard, and is designed to
match your rocker type controls in size and appearance.
The detectors are rugged and attach easily and quickly to
each hydraulic cylinder. The attached readout line runs
up to the light panel with simple plug in connections.
Insta-Trim electonic tab locators can be added to your
existing boat leveler system, upgrading your system for a
better, more accurate performance.
Installation is quick, easy, and simple. Only a few
common tools are rquired, and the tab locators come
with easy to follow instructions.
|
364.50 |
|
|
Aluminum Inboard Cylinder - 1.25" Bore & 7" Stroke
A hydraulic steering system consists of a steering pump, a cylinder tied to the rudder or the outboard or sterndrive engine, and the connecting hoses. Under normal operating conditions, a steering wheel turn will pump the oil, which flows in through the hoses to the cylinder, according to the turn direction.
With the consequent cylinder movement, the oil will flow to the pump through the hoses and, at the same time, move the engine or the helm, which are connected to the cylinder. The pumps, equipped with a valve that prevents outgoing fluid from returning along the same hose, allow the operation of the steering systems with two or more steering stations. The cylinders are double-acting and may be balanced or unbalanced. This particular cylinder is a balanced cylinder with the same number of steering wheel turns to move the helm from the center to the end stroke in two opposite directions. A well-balanced steering system needs the correct choice of pump for the cylinder.
This hydraulic cylinder for the inboard engine UC 116-I has been designed and manufactured to be used as a component in the hydraulic steering systems. The cylinder with a mobile rod is installed directly to the arm of the helm through the proper ball joint on the end part of the cylinder. On the opposite side, it is fixed directly to the boat through a support with the plate.
Features:
Balanced (the number of turns lock-to-lock is equal to port to starboard or vice versa)
Specifications:
Volume: 116 cc - 7 cu.in
Torque: 58 kg (5043 lbs.)
Output Force: 464 kg (1023 lbs)
|
394.75 |
|
|
Repair kits for Baystar hydraulic cylinders.
|
149.99 |
|
|
Repair parts for SeaStar hydraulic cylinders.
|
52.99 |
|
|
Repair kits for SeaStar hydraulic cylinders.
|
214.99 |
|
|
Smart Tabs II Series Trim Tabs 16 X 10 f/23-30' Boats - 6500lbs Max
IMPROVES YOUR BOATS OVERALL PERFORMANCE - GUARANTEED!!!
If these trim tabs don't provide you with an outstanding performance increase, contact us within 30 days of your purchase.
Why buy a manually adjusting trim tab set when you can get the automatic trim tabs that will self adjust and performance better for less money?
Designed for boats 23' - 30' weighing up to 6500 lbs The ST 1610 Series is ideal for low profile Fiber Glass, Aluminum, and RIB design boat with transom widths less than 10 feet (trailerable boats). This heavy duty system provides an active suspension system for the boat that increases stability and smooths the ride even in rough seas. Easier planning at slower speeds, increased payload performance, improved tracking and handling are available automatically without the need for pilot interface. No switches, no electric or hydraulic connections, and no maintenance. Just get in and go!
Specially designed for boats between 23' and 30", under 10' in width, and up to 8,500 Lbs gross weight. The ST1610 series features two nitrogen gas actuators per plate providing increased stern lift and twice the reactive dampening, eliminating any instant changes from water pressure variances. This fully automatic and active system provides smooth and undetectable reaction to boat speed, and water conditions creating a level more comfortable ride.
Our breakthrough technology in trim tabs is completely automatic requiring no operator adjustment while underway. Nauticus trim tabs self adjust according to how you load and maneuver your boat.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.
Reduce the minimum planning speed by up to 33%
Faster Acceleration
Increase top speed
Provide a level, more comfortable ride at lower speeds
Improve fuel economy, handling and safety
NO HYDRAULICS - NO ELECTRIC SWITCHES
Nauticus trim tabs are completely automatic requiring no operator adjustment while underway.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.(see installation instruction).
SPEED REGULATION
Nauticus trim tabs start in a downward angel to maximize lift at slow speeds. As the boat accelerates, the water pushes up on the trim plates providing lift to the stern which minimizes bow rise, and allows the boat to plane quickly.
Once the water pressure exceeds the actuator load rating (maximum lift) the trim plates move up to a horizontal position eliminating any drag.
BOAT STABILIZERS
Even when cruising SMART TABS continue to work like shock absorbers. The constant adjustment to sea conditions allow SMART TABS to provide remarkable stability in turns, while crossing waves, while cruising, and while running at maximum speeds. No more sliding, porpoising, or chine walking.
ONE OF A KIND
The unique system is the only one of its kind in the industry. The internal valve system is truly "smart" in its design of controlling you boats performance.
It will reduce the minimum planning speed by 33%
Provide a level, more comfortable ride at lower speeds
Improve economy, handling and safety
As the boat speed increases, the water pressure also increases. Once the water pressure exceeds the Actuator load rating (maximum LIFT period) the trim plates begin to move upward until they are horizontal with the bottom of the boat.
The internal valve system dampens the trim plate movement which eliminates any instant reaction to minor water pressure variances. Nauticus trim tabs provide smooth and undetectable reaction to boat speed creating a level, more comfortable ride at lower speeds.
INSTALLATION IS SIMPLE
With an electric drill, small drill bit, a phillips screwdriver, and two wrenches, just about anyone can install SMART TABS in less than an hour. Professional installers should be able to install SMART TABS in 30 minutes or less.
All mounting hardware, instructions, and templates are included.
SMART TABS require NO THROUGH HULL DRILLING
|
237.46 |
|