Marine Hull Mount Horn - White Features: For vessels under 12 meters (39.4 ft.) 12 or 24 volt DC system Built-in water evacuation drainage system

Marine Hull Mount Horn - Black Features: For vessels under 12 meters (39.4 ft.) 12 or 24 volt DC system Built-in water evacuation drainage system

Marine Hidden Horn - White Features: 12 or 24 Volt DC Systems For vessels under 12M (39.4') Uses "SETS" Horn Technology Draws less than 1/2 Amp Unit is Polarity Protected Solid state with no moving parts Built-in water evacuation drainage system Requires 2-1/4" hole Mounting gasket included

Marine Hidden Horn - White with Stainless Steel Overlay Features: 12 or 24 Volt DC Systems For vessels under 12M (39.4') Uses "SETS" Horn Technology Draws less than 1/2 Amp Unit is Polarity Protected Solid state with no moving parts Built-in water evacuation drainage system Requires 2-1/4" hole Mounting gasket included

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Marine Hidden Horn - Black Features: 12 or 24 Volt DC Systems For vessels under 12M (39.4') Uses "SETS" Horn Technology Draws less than 1/2 Amp Unit is Polarity Protected Solid state with no moving parts Built-in water evacuation drainage system Requires 2-1/4" hole Mounting gasket included

4.5" Round Hailer/PA Horn - White 4.5" Round PA/Hailing horn Compatible w/GX2200S/GX3000S/GX5000S/GX5500S/VLH-3000 30 Watt horn 4 Ohm

240SW 5 x 8 Hailer/PA Horn - White Features: 5 x 8" Rectangular 4 OHM PA/Hailing horn Compatible w/GX2000/GX2200/GX6000S and VLH-3000A 4 ohm 40 watt horn

Sonic Mini Compact Horn - White  These Sonic Mini Compact Horns feature ASA plastic covers for impact and UV resistance. Mounting bracket can be used as a wiring template. Horn wiring has no polarity, so the negative or positive wire can be attached to either side. When installed, horns should point slightly downward to permit water drainage. At 108 decibels and a frequency (Hz) of 440±20A, this horn meets US Coast Guard's COLREGS and ABYC standard A-23 for use on vessels under 12m (39'). 12VDC. 12VDC. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Docking, Hull, Back-Up LED Lights - Chrome Features: Sold as a Pair Operates 12 Volt DC Systems Draws 4 Amps Each Sealed Built-in Rear Heat Sink Thermal Insulated Wires Pyrex Optical Lens Spring Loaded Lamp Assembly Removable Lens Cover Water Tight Gaskets Included 7.60" x 4.15" x 3.75"

4" x 6" Weatherproof PA Speaker Horn - White Features: Frequency Response: 200Hz - 15kHz Sensitivity (1W/1M): 110dB Dimensions: 8" L x 6" W x 4" H Includes stainless steel mounting hardware and ABS plastic base Bracket pivots 90°

Portable Navilight 360° 2NM Rescue - Glow In The Dark - Green w/Bendable Suction Cup Mount The Navilight 360° Rescue Edition 2NM - US Coast Guard approved for 2 nautical miles is based on the Navi light 360° 2NM and includes a 360° All-round light, 225° Masthead light, 135° Sternlight, Flashing light, Anchoring light and a Cabin light. Additionally it is fitted with a glow in the dark circle around the switch. These unique glow pigments glow for 8 hours after only 10 minutes of exposition to daylight. This and the emergency green color of the body, makes Navi light 360° Rescue Edition 2NM extremely easy to locate, day and night. It uses super bright LED light, is water proof, floats and attaches almost anywhere through its double magnetic mounting system. Examples of usage: *Based on the Convention on the International Regulations for Preventing Collisions at Sea, commonly called 72 COLREGs In a vessel of 12M or more in length but less than 50M in length: As Sternlight As Flashing light As All-round light In vessels of less than 12M in length: As Masthead light As Sternlight As All-round light Specifications: USCG Approval, 2 Nautical Miles 5 Modes: 360° All-round light, 225° Masthead light, 135° Sternlight, Flashing light, Anchoring light, Cabin light Floatable, waterproof (20M) and air-tight Includes magnet bracket, mounting screw, 3 lanyards for multiple fixing and securing Powered by three AAA batteries (not included) Size: H = 35mm, Diameter = 68mm Weight (net): 115g Modes / approximate burn time: 16 white LED, 360° All-round light, Anchoring light / 15hrs 16 white LED, 360° Flashing light / 85hrs 10 white LED, 225° Masthead light / 24hrs 6 white LED, 135° Sternlight / 32hrs 4 white LED, 360° Cabin light / 72hrs Bendable Suction Mount Designed to allow secure mounting of the Navi lights with magnetic base on any kind of smooth and flat surfaces. The quick release suction cup releases with just one push of the lever so it can be stored quickly or mounted to another place or boat. Examples of Usage: Navigation lights should be mounted so that they are not covered by the vessel's superstructure or may interfere with deck lights. The bendable suction mount can be easily used to mount the magnetic Navi lights at: The outboard engine The steering console, the windshield or any place on the hull where the lights are seen best On canoes and kayaks with a smooth and flat surface Specifications: Secure suction cup base Quick release suction cap Bendable shaft moves through 180° Self adhering plastic mounting plate Diameter = 75mm for secure mounting on rough surfaces Size: L = 68mm, H = 157mm Weight (net): 80g WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Portable Navilight 2NM - TriColor w/Bendable Suction Cup Mount The Navilight Tricolor 2NM - US Coast Guard approved for 2 nautical miles includes a green light to be shown at the starboard side and a red light to be shown at the port side. In addition, it includes the white Sternlight, to be used at the stern. It is battery operated, uses super bright LED light, is water proof, floats and attaches almost anywhere through its double magnetic mounting system. The green as well as the red lights show an unbroken light over an arc of the horizon of 112,5°. The white Sternlight shows an unbroken light over an arc of the horizon of 135°. All lights work independently, in a combination of all three or red/green together. Examples of usage: *Based on the Convention on the International Regulations for Preventing Collisions at Sea, commonly called 72 COLREGs On a power-driven vessel of 12M or more in length but less than 50M in length: As green or red sidelight As sternlight On a power-driven vessel of less than 12M in length: as green or red sidelight as combined green / red as sternlight On a sailing vessel underway: as green or red sidelight as sternlight On a sailing vessel of less than 20 meters in lengths as backup light: Tricolor lantern at or near the top of the mast Specifications: USCG Approval, 2 Nautical Miles 5 Modes: Tricolor Masthead light (135° white, 112,5° red, 112,5° green), BiColor side light, red side light, green side light, white Sternlight Floatable, waterproof (20M) and air-tight Includes magnet bracket, mounting screw, 3 lanyards for multiple fixing and securing Powered by three AAA batteries (not included) Size: H = 35mm, Diameter = 68mm Weight (net): 118g Modes / approximate burn time: 16 green / red / white LED, 360° TriColor lantern / 12hrs 10 green / red LED, 225° Bi-Color sidelight / 20hrs 5 green or 5 red LED, 112,5° sidelight / 38hrs 6 white LED, 135° Sternlight / 32hrs Bendable Suction Mount Designed to allow secure mounting of the Navi lights with magnetic base on any kind of smooth and flat surfaces. The quick release suction cup releases with just one push of the lever so it can be stored quickly or mounted to another place or boat. Examples of Usage: Navigation lights should be mounted so that they are not covered by the vessel's superstructure or may interfere with deck lights. The bendable suction mount can be easily used to mount the magnetic Navi lights at: The outboard engine The steering console, the windshield or any place on the hull where the lights are seen best On canoes and kayaks with a smooth and flat surface Specifications: Secure suction cup base Quick release suction cap Bendable shaft moves through 180° Self adhering plastic mounting plate Diameter = 75mm for secure mounting on rough surfaces Size: L = 68mm, H = 157mm Weight (net): 80g WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Portable Navilight 360° 2NM - White w/Bendable Suction Cup Mount The Navilight 360° 2NM - US Coast Guard approved for 2 nautical miles is the most versatile light of Navisafes range of battery operated portable navigation lights and includes a 360° All-round light, 225° Masthead light, 135° Sternlight, Flashing light, Anchoring light and a Cabin light. It uses super bright LED light, is waterproof, floats and attaches almost anywhere through its double magnetic mounting system. Examples of Usage: *Based on the Convention of the International Regulations for Preventing Collisions at Sea On a power-driven vessel underway of 12 meters or more in length but less than 50 meters in length: Sternlight All-round white light On a power-driven vessel underway of less than 12 meters in length: Masthead light Sternlight All-round white light On a power-driven vessel underway of less than 7 meters in length whose maximum speed does not exceed 7 knots: All-round white light Rowing/Paddle Vessels All-round white light Anchored vessels and vessels aground Anchor lights must always be shown from sunset to sunrise All-round white light Specifications: USCG Approval, 2 Nautical Miles 5 Modes: 360° All-round light, 225° Masthead light, 135° Sternlight, Flashing light, Anchoring light, Cabin light Floatable, waterproof (20 m) and air-tight Includes magnet bracket, mounting screw, 3 lanyards for multiple fixing and securing Powered by three AAA batteries (not included) Size: H = 35 mm, Diameter = 68 mm Weight (net): 113 g Modes / approximate burn time: 16 white LED, 360° All-round light, Anchoring light / 15hrs 16 white LED, 360° Flashing light / 85hrs 10 white LED, 225° Masthead light / 24hrs 6 white LED, 135° Sternlight / 32hrs 4 white LED, 360° Cabin light / 72hrs Bendable Suction Mount Designed to allow secure mounting of the Navi lights with magnetic base on any kind of smooth and flat surfaces. The quick release suction cup releases with just one push of the lever so it can be stored quickly or mounted to another place or boat. Examples of Usage: Navigation lights should be mounted so that they are not covered by the vessel's superstructure or may interfere with deck lights. The bendable suction mount can be easily used to mount the magnetic Navi lights at: The outboard engine The steering console, the windshield or any place on the hull where the lights are seen best On canoes and kayaks with a smooth and flat surface Specifications: Secure suction cup base Quick release suction cap Bendable shaft moves through 180° Self adhering plastic mounting plate Diameter = 75mm for secure mounting on rough surfaces Size: L = 68mm, H = 157mm Weight (net): 80g WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

FM-S10RW FM Series 10" 400W Flush Mount Marine Subwoofer - Round Grill - White Clear audio, clean aesthetics, all-class. Engineered for high-quality audio reproduction with innovative design aesthetics, Fusion's FM Series flush mount marine subwoofers are designed to deliver high-quality bass to your vessel in a sleek and minimalistic form factor to meet the latest boat design trends. Featuring an intelligent mounting system for non-intrusive, easy installation, the FM Series subwoofers are designed to be flush mounted with a mounting flange no thicker than 3mm [1/8"] for a premium, visually-appealing, near-flat finish. With an IP65 weatherproof rating, True-Marine™ accreditation and an industry-leading 3-year warranty, you can enjoy peace of mind that your FM Series subwoofers are built to last on board season after season. Features: Optimized 2.1 Configuration: When connected with a pair of FM Series speakers and a Fusion Multi-Zone™ stereo with DSP, you have the option of creating a 2.1 audio zone to simplify installation and reduce system cost by adding bass without the need for an external amplifier. Quality Audio Reproduction: Enjoy quality low frequency audio at any volume level. Innovative Design Aesthetics: Designed with a low profile, near-flat installation for a visually appealing finish, the FM Series will complement the aesthetics of any vessel. Non-Intrusive Mounting System: The FM Series uses 'speaker legs' that keep the subwoofer in place without creating any screw holes to your vessel. True-Marine™ Designed and Engineered: Extensively tested to perform in the harsh marine environment, the FM Series carry an IP65 weatherproof rating along with True-Marine accreditation. Designed To Comply With ISO12216: Tested to international standards for pressure and watertightness, it recognizes the FM Series are designed and built to the highest industry standards for quality and robustness. Specifications: Subwoofer Size: 10" Peak Power: 400W RMS Power Rating: 120W Efficiency (1W/1M): 87 dB Frequency Response: 30 Hz - 2 kHz Nominal Impedance: 4 Ohms Recommended Amplifier Power (RMS): 40-300 W/Ch Cone/Surround Material: Polypropylene with rubber surround Mounting Diameter Clearance: 269mm (10-9/16") Mounting Depth Clearance: 140mm (5-1/2") Optimum Enclosure Volume (Sealed enclosure, fully filled with absorption material): 40L Operating Temperature Range: 0-50°C (32-122°F) Storage Temperature Range: -20-70°C (-4-158°F)  Water and Dust Resistance (IPX rating): IP65 Warranty: 3 Years WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.