RT Screw Terminal 12 Circuit Dual Lever Bus Bar This Egis bus bar seamlessly integrates with RT fuse blocks, can be used as a standalone ground bus, or can be assembled with an existing RT Series fuse block line. Also, this multi-level low-amp has terminal screws for improved mounting. Applications: The 12-circuit block ensures ground connection reliability with this compact and well-constructed ground bus block. RT series connection compatibility enables a smaller installation footprint and convenient negative terminal access when installed with a fuse block application. Features: Bullet-proof construction - designed with high-temperature materials and stainless steel self-locking hardware, allows mounting anywhere on the vehicle Seamlessly integrates with RT fuse blocks - use as a standalone ground bus or assembled with existing RT series fuse block lines Specifications: Maximum Current (Entire Block) Amps: 100 Maximum Current (Per Circuit) Amps: 30 Max Output Wire Size: #10 AWG Voltage Range VDC: 0-36 Number of Fuse Positions: 12 Output Terminal Connection Ring Terminal Size: M4 / (#8) Focal Features: Robust Materials For Harsh Environments All attachment hardware is constructed of stainless steel with self-locking mechanisms for long-lasting installations. A plated copper alloy bus bar conductor withstands corrosion and maximizes conductivity. Engineering-grade composite insulators support high-temperature application exposure, such as in engine compartments. Seamlessly Integrates With RT Fuse Blocks It can be installed individually on its own or assembled to the end of a 6, 12, or 18-position RT Series fuse block for a more compact overall footprint.

5026 ST Blade Fuse Block with Cover - 12 Circuit with Negative Bus  Features: Clear insulating cover with label recesses accept Small Format Labels Cover Satisfies ABYC/USCG requirements for insulation Tin-plated copper buses and fuse clips give 30 Amperes rating per circuit Accepts ATO and ATC fast acting blade fuses 20 write-on circuit labels included WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

5031 ST Blade Fuse Block w/out Cover - 12 Circuit w/ Negative Bus Tin-plated copper buses and fuse clips give 30 Amperes rating per circuit Accepts ATO and ATC fast acting blade fuses WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RT Fuse Block 12 Position with Ground & LED Indication This 12-position fuse block has a modular design that can produce seven (7) unique configurations from Egis 8028 & 8030 and reduce part numbers to stock for all build requirements. Also, this fuse block has a ground and LED indication. Applications: Blown fuse LEDs speed up the correction of system faults and improve the ability to remotely diagnose customer issues. Harsh environment design with stainless steel self-locking hardware and optional weather-proof labels in standard or customized options. Features: Bullet-proof construction - designed with high-temperature materials and stainless steel self-locking hardware allows mounting anywhere on the vehicle Protects branch circuits by accepting ATO style fuses ranging from 1 through 40 Amps Supports SAE circuit protection standards for thermal/short circuit events Specifications: Maximum Current (Entire Block) Amps: 10 Maximum Current (Per Circuit) Amps: 30 Max Output Wire Size: #10 AWG Voltage Range VDC: 0-36 Number of Fuse Positions: 12 Compatible Fuse Types: ATO / ATC / ATF Focal Features: Spare Fuse Locations Two locations per 6 circuits for spare or test resistors to reduce siren volumes during evaluation. Stainless Steel Self-Locking Hardware 100 % non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. LED Fuse Diagnostics Blown fuse LED indication for each output circuit provides a clear indication of faulty circuits and eases troubleshooting issues remotely. Cover/ Label Recesses Protects terminal studs and cable terminal edges from inadvertent shorts to each other or ground. Ground Block Included Includes a 12-position ground return block with multi-level low amp terminal screws for improved mounting. Ground Block Separates The ground block section optionally separates from the fuse block section, affording increased deployment options for challenging installations.

RT Fuse Block 12 Position with LED Indication This 12-position fuse block has a modular design that can produce seven (7) unique configurations from Egis 8028 & 8030 and reduce part numbers to stock for all build requirements. Also, this fuse block has an LED indication. Applications: Blown fuse LEDs speed up the correction of system faults and improve the ability to remotely diagnose customer issues. Harsh environment design with stainless steel self-locking hardware and optional weather-proof labels in standard or customized options. Features: Bullet-proof construction - designed with high-temperature materials and stainless steel self-locking hardware, allows mounting anywhere on the vehicle Protects branch circuits by accepting ATO style fuses ranging from 1 through 40 Amps Supports SAE circuit protection standards for thermal/short circuit events Specifications: Maximum Current (Entire Block) Amps: 100 Maximum Current (Per Circuit) Amps: 30 Max Output Wire Size: #10 AWG Voltage Range VDC: 12-24 Number of Fuse Positions: 12 Compatible Fuse Types: ATO / ATC / ATF Focal Features: Spare Fuse Locations Two locations per 6 circuits for spare or test resistors to reduce siren volumes during evaluation. Stainless Steel Self-Locking Hardware 100 % non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. LED Fuse Diagnostics Blown fuse LED indication for each output circuit provides a clear indication of faulty circuits and eases troubleshooting issues remotely. Cover/ Label Recesses Protects terminal studs and cable terminal edges from inadvertent shorts to each other or ground.

Programmable Automatic Charging Relay (ACR) 160A, 12V This 160A Egis charging relay is automatic and programable. The relay eliminates dead start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present. Applications: Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance. Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell. Features: Ultra-Low Power Draw Compared to typical ACRs (7-10 mA) vs 7610 ACR @ 1.3 mA, will not deplete batteries even after extended electrical system downtime. Simple and robust installation - The integrated sealed plug eliminates corrosion and includes a Deutsch/Amphenol DTM connector harness Start Assist input option to ensure maximum cranking amps are available by allowing the manual connection of batteries via a remote switch. Bullet-proof construction - Sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere. Integrated thermal overload shutdown protection. Additional low-amp output can be used to report device status remotely or drive a secondary relay for charging a battery bank without a charge source (see example) Specifications: Continuous Current (Amps): 160 Voltage Range: 8-18 VDC Off-State Current Draw mA: 1.3 Interrupt Current (Amps): 240 ACR Closing Voltage (VDC): 12.9-13.6 ACR Opening Voltage (VDC): 12.1-12.8 Focal Features: Top Side Dip Switches Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover. Stainless Steel Self-Locking Hardware 100% Non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. Integral I/O Connector Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products. Connection Options Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads). Easy Integration with RT Fuse Blocks (24 HR Circuits) Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series Fuse Blocks. LED Diagnostics Provides an indication of pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.

Automatic Charging Relay Plus - 160A - 24V This 160A Egis automatic charging relay eliminates dead-start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present. Applications:  Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell Features: Ultra-low power draw compared to typical ACRs (7-10 mA) vs. the 7610 ACR @ 1.3 mA will not deplete batteries even after extended electrical system downtime. Simple and robust installation - integrated sealed plug eliminates corrosion; includes Deutsch/Amphenol DTM connector harness Start to assist input option to ensure maximum cranking amps are available by allowing manually connecting batteries via a remote switch Bullet-proof construction - sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere; Integrated thermal overload shutdown protection Additional low-amp output can be used to report device status remotely or drive a secondary relay for charge to a battery bank without a charge source (see examples) Specifications: Continuous Current Amps: 160 Voltage Range (VDC): 16 – 36 Off-State Current Draw (mA): 1.3 Interrupt Current (Amps): 240 AC Closing Voltage Range (VDC): 25.8-27.2 AC Opening Voltage Range (VDC): 24.2-25.6 Focal Features: Top Side Dip Switches Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover. Stainless Steel Self-Locking Hardware 100% non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. Integral I/O Connector Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products. Connection Options Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads).  Easy Integration with RT Fuse Blocks (24 HR Circuits) Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series fuse blocks.  LED Diagnostics Indicates pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.

XD Relay Cross-Over Bus Bar The XD Relay Cross-Over Bus Bar allows users to link together Egis XD Single, Dual, and Triple XD Relays to each other in multiple configurations and even to the Egis 8700 Mechanical Disconnect.  Linking relays together creates compact installations and allows for robust circuit switching and battery management. Features: Tin-Plated Copper to ensure reliable circuit connectivity and anti-corrosive features keep it last long term. Robust Protective Insulation ensures no accidental contact shorts between XD relays. Specifications: Continuous Current (Amps): 500 Max Voltage (VDC): 72 Material: Tin-plated copper Size (L x W): 90 x 47mm Thickness: 2.8mm (1/8") Terminal Stud Hole Size: 10.5mm (3/8”)

XD Relay Link Busbar This tin-plated copper is to ensure reliable circuit connectivity and an anti-corrosive feature that will keep it long-lasting. Applications Link Together XD Single, Dual, and Triple XD relays to each other in multiple configurations and even to Egis's 8700 Mechanical Disconnect. Linking relays together creates compact installations and allows for robust circuit switching and battery management. Features: Great electrical conductivity with anti-corrosion tin plating keeps connections reliable This bus bar is tough and built to withstand high amperage loads and resist deformation from nut-tightening Save install space by linking XD Relays together for even more capability and maintain a professional-looking install Specifications: Continuous Current (Amps): 500 Max Voltage (VDC): 72 Material: Tin-plated copper Size (L x W): 47.8mm x 22.8mm  Thickness: 2.8mm (1/8”) Terminal Stud Hole Size: 10.5mm (3/8”)

ST CLB Circuit Breaker Block - 12 Position w/Negative Bus Features Quick connect clips allow circuit breakers to snap easily into place Tin-plated copper busses and screw terminals Clear insulating cover with square format label recesses, satisfies ABYC/USCG insulation requirements Easy to open clip on cover Breakouts allow wire access in two directions Accepts ring terminals Optional push button waterproof boots or dress nuts can be installed over cover Specifications: Circuits: 12 Maximum Amperage: 100A (per block) 32A (per circuit) Maximum Voltage: 32V DC Mounting: #8 Screw (M4) or #8 Nut Negative Bus: Yes Source: Common SourceMinimum Operating Temperature: -10° C Maximum Operating Temperature: 60° C Mounting Centers: 10.13"(257.3 mm) Screw Terminal Type: #8-32 Screws with Captive Star Lock Washer Height: 6.69"(169.93 mm) Weight: 1.50lb (0.68 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

150 Ampere Common Busbar 20 x 8-32 Screw Terminal with Cover PN:   2312 Stud design provides direct terminal to bus contact for low resistant connection Stainless steel studs and screws allow high torquing for excellent electrical contact Tin-plated copper bus for maximum conductivity and resistance to corrosion UL 94-VO rated (self extinguishing) base material resists high heat Press on insulating cover attaches to studs and allows unobstructed wire access Raised bus provides easy access to multiple wires on a single screw Continuous Amperage 130 Amperes AC 150 Amperes DC Maximum Voltage Rating 300 Volts AC 48 Volts DC Bus Material Tin-Plated Copper CDA 110/UNS11000 Base Material Glass Reinforced Polycarbonate Cover Material Polycarbonate Studs Stainless Steel, 1/4"-20, torque 72 in-lbs, accepts 1/4" (M6) ring terminal Screws Stainless steel, #8-32 screw terminal, torque 18 in-lbs, accepts #8 (M4) ring terminal Weight 0.58Lb WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Blade Style LED Indicator Fuse Block with Negative Bus Bar - 6 Circuit Nickel Plated Copper/Stainless Steel/Injection Molded ABS. Features: Red LED lights indicate when fuse is blown or missing Uses ATO/ATC & ATM fuses 1A-30A Main line terminal rating is 100A 32VDC max, with M5 metric threaded studs Single line terminal rating is 30A 32VDC max, with M4 metric threaded studs Includes semi-transparent cover and 71 labels Terminals are nickel plated copper with stainless steel screws Installs with four #8 FH fasteners (not included) WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Blade Style LED Indicator Fuse Block with Negative Bus Bar - 12 Circuit Nickel Plated Copper/Stainless Steel/Injection Molded ABS. Features: Red LED lights indicate when fuse is blown or missing Uses ATO/ATC & ATM fuses 1A-30A Main line terminal rating is 100A 32VDC max, with M5 metric threaded studs Single line terminal rating is 30A 32VDC max, with M4 metric threaded studs Includes semi-transparent cover and 71 labels Terminals are nickel plated copper with stainless steel screws Installs with four #8 FH fasteners (not included) WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Dual Buss Bar with Cover - 12 Terminals This dual bus bar is designed for DC positive or negative distribution on one block or AC neutral and safety ground collection on one block. Constructed of corrosion-resistant tin-plated Copper and ABS with a polycarbonate cover. Features: Includes two 1/4"-20 stainless steel stud terminals and six #8-32 stainless steel screw terminals per buss Installs with four #8 FH fasteners (included) 48VDC, 150A per buss; 300VAC, 150A per buss CE and RoHS compliant Specifications: Terminals: 12 Length (inch): 5-1/2" Width (inch): 2-3/4" Depth (inch): 1-11/16" Max. Amps: 150 Fastener: #8 FH Weight: 0.59 lb.

MiniBus 100 Ampere Common BusBar 5 x 8-32 Screw Terminal with Cover PN:   2314 Great for limited space applications in electronics cabinets and under dashboards Snap on insulating cover attaches to studs and allows unobstructed wire access Raised bus provides easy access to multiple wires on a single screw Pressed on busbar eliminates the need for securing nut Stainless steel studs allow high torquing for excellent electrical contact Tin-plated copper bus for maximum conductivity and corrosion resistance = Recessed mounting holes eliminate accidental shorts to aluminum and steel mounting surfaces Captive star type lock washers meet CE requirements for anti-rotation and eliminate handling of small, easily dropped parts Stainless steel Phillips screws for easier installation and resistance to stripping UL 94-VO rated base material resists high heat Continuous Amperage 130 Amperes AC/DC Maximum Voltage Rating 300 Volts AC/48 Volts DC Bus Material Tin-Plated Copper CDA 110/UNS11000 Base Material Reinforced Polycarbonate Cover Material Clear Polycarbonate Weight 0.17Lb WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.