Smart Dual Battery Isolator This Smart Dual Battery Isolator is ideal for dual battery applications. Allows two batteries to automatically charge at the same time and then isolates the batteries, ensuring the starting battery is always charged and ready for use. Automatically engages or disengages the circuit at pre-set voltages by sensing the input voltage generated, eliminating the possibility of discharging the primary starting battery. Cut-in voltage: 13.3V. Cut-out voltage: 12.8V. Surge protected. Features an LED indicator to alert the user when the unit is engaged. Constructed of machined brass with a weatherproof injection molded nylon housing and durable silver tipped contacts. Installs with two #8 RH fasteners (included). 12VDC. 140A. IP65 rating. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Round Dual USB & USB-C Power Socket USB & USB-C Power Socket charges two devices simultaneously. The total output 4.8A load is split 2.4A per side as needed. USB-C features Power Delivery (PD) for faster and more flexible charging. Enough power to charge phones, pads, and tablets quickly and efficiently. A protective dust cap extends the life of the charger. Features:  Constructed of injection molded nylon  Installation is as easy as drilling a 1-1/8" hole, inserting the socket body, tightening the locking nut, and connecting the wires  Also, fits Sea-Dog® Power Socket Shell (426100) and Mounting Bracket (426105) Blue LED illumination  IP65 rating  CE and RoHS compliant Specifications: Output DC: 5V/4.8A  Input 8-32VDC  USB-C Watts: 60W@24V  USB Watts: 36W@12V Plug-In Side Diameter: (inch) 1-7/16" Length: (inch) 1-1/2" *Sold as an Individual

SEA-DOG Sea-Dog Line carries quality marine gear such as Deck Hardware, Hinges, Lighting, Plumbing, Fishing Equipment, Clamcleats, Chain and Rigging Hardware and more.

2-Bank Battery Isolator, 200A, 40V Analytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electrical isolation between the battery banks or between a vehicle and trailer. Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time. While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load. Features: Waterproof Expoxy Sealed Construction Easy Connection Alternator/Charger post 5/16", Battery Post 1/4" Most Efficient use of Available Alternator Output Maximize Battery Performance Three year parts and labour warranty

200A, 40V 3-Bank Ideal Battery Isolator Features: Waterproof Expoxy Sealed Construction Easy Connection Most Efficient use of Available Alternator Output Maximize Battery Performance Three year parts and labour warranty Analytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electrical isolation between the battery banks or between a vehicle and trailer. Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time. While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load.

Single Bank Battery Isolator, 200A, 40V Analytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electrical isolation between the battery banks or between a vehicle and trailer. Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time. While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load. Features: Waterproof Expoxy Sealed Construction Easy Connection Alternator/Charger Post 5/16", Battery Post 1/4" Most Efficient use of Available Alternator Output Maximize Battery Performance Three year parts and labour warranty

Dual USB-C Power Socket A dual USB-C Power Socket charges two devices simultaneously. The total output 8A load is split 4A per side as needed. USB-C features Power Delivery (PD) for faster and more flexible charging. Enough power to charge phones, pads, and tablets quickly and efficiently. A protective dust cap extends the life of the charger. Features:  Constructed of injection molded nylon  Installation is as easy as drilling a 1-1/8" hole, inserting the socket body, tightening the locking nut, and connecting the wires  Also, fits Sea-Dog® Power Socket Shell (426100) and Mounting Bracket (426105) Blue LED illumination  IP65 rating  CE and RoHS compliant Specifications: Output DC: 5V/8A Input: 8-32VDC USB-C Watts: 60W@24V  Plug-In Side Diameter: (inch) 1-7/16"     Length: (inch) 2-1/4" *Sold as an Individual

Dual USB Power Plug with Voltage/Amp Meter  LCD screen displays charging status in amps, battery voltage, and low voltage audio alarm. Stamped stainless steel and injection molded nylon construction this USB power plug adapter charges two devices simultaneously. Input 12-24V, Single output DC 5V/2.4A. Total output is a 4.8A with the load being split between the two sides as needed. Enough power to charge iPhones, iPads and most other devices. Can be used on a boat, car, or RV. This portable version fits all Sea-Dog® Power Sockets and any standard 12V receptacle. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Argofet 200-2 Battery Isolator - 200AMP - 2 Batteries Similarly, to Argodiode battery isolators, Argofet isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger) without connecting the batteries. Discharging the accessory battery, for example, will not result in discharging the starter battery.   In contrast with Diode battery isolators, FET isolators have virtually no voltage loss. The voltage drop is less than 0,02 Volt at low currents and averages 0,1 Volt at higher currents. When using Argofet battery isolators, there is no need to also increase the output voltage of the alternator. However, care should be taken to keep cable lengths short and of sufficient cross-section. Example: When a current of 100 A flows through a cable of 50 mm² cross section (AWG 0) and 10 m length (30 ft), the voltage drop over the cable will be 0,26 Volt. Similarly, a current of 50 A through a cable of 10 mm² cross section (AWG 7) and 5 m length (15 ft) will result in a voltage drop of 0,35 volts! Alternator Energizes Input Some alternators need DC voltage on the B+ output to start charging. DC will be present when the alternator is directly connected to a battery. Inserting an Argodiode or Argofet splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new Argofet Isolators have a special current-limited energize input that will power the B+ when the engine run/stop switch is closed.  Specifications: Maximum Charge Current (A): 200 Maximum Alternator Current (A): 200 Number of Batteries: 2 Nominal Battery Voltage: 12V and 24V Connection: M8 bolts Weight kg (lbs): 1,4 (3.1) Dimensions (H x W x D): 65 x 120 x 200 mm (2.6 x 4.7 x 7.9 inches) Please contact your dealer for any returns, repairs or support issues related to this product.

Battery Isolators

Dual USB Socket/Voltmeter with Hidden Display This Dual USB Socket allows for two devices to be charged simultaneously while also displaying the batteries output. The total output 4.8A load is split 2.4A per side as needed. Enough power to charge phones, pads, and tablets quickly and efficiently. Also fits Sea-Dog® Power Socket Shell 426100. Output DC 5V/4.8A. Input 12-24VDC. Red LED display. IP65 rating. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Smart Cleat 6" Deck Mount Investment Cast 316 Stainless Steel The Smart Cleat provides easy line tie-off in a classic style. Knob end prevents lines from easily slipping off and minimizes potential collision injuries. Constructed of corrosion resistant investment cast 316 stainless steel. Open base mount cleats install with four 1/4" FH fasteners (not included).

Smart Cleat 6" Stud Mount Investment Cast 316 Stainless Steel The Stud Mount Smart Cleat provides easy line tie-off in a classic style. Knob end prevents lines from easily slipping off and minimizes potential collision injuries. The stud mounted fasteners are hidden, leaving no exposed fasteners to collect water or debris. Studs are 1/4"-20 x 1-1/2". Installation is easy with two standard bit size holes drilled for the studs (no cutouts or hole saws required). Includes stainless steel washers and nuts. Constructed of corrosion resistant investment cast 316 stainless steel.

Argo Diode Battery Isolator - 160AMP - 2 Batteries Diode battery isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.

Argo FET Battery Isolator - 100AMP - 2 Batteries Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents. Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.