Flotec FP4212 Cast Iron Convertible Jet Pump 1/2 HP KEY FEATURES Superior performance at depths to water of 100' or less Rugged, heavy-duty pump housing Ready-to-install dual-voltage 115v/230v motor - see manual for 230 volt conversion Pressure switch pre-wired with 30-50 PSI pressure setting WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1/2 MAXIMUM CAPACITY:  7.9 GPM (shallow setup) FLOW at 10' LIFT and 40 PSI:  7.1 GPM (shallow setup) MAX LIFT:  25' for shallow setup / 70' for deep setup MAXIMUM PRESSURE:  60 psi (shallow setup) / 54 psi (deep setup) PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DRIVE PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1"NPT AMP DRAW (full load):  9.9 Amps on 115V / 4.95 Amps on 230V VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service. KEY FEATURES Superior performance at depths to water of 100' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  9 GPM (shallow well setup) FLOW AT 10' LIFT and 40 PSI:  7.8 GPM (shallow well setup) MAX LIFT:  25' w/ shallow well jet kit / 70' w/ deep well jet kit MAX PSI:  62 psi (shallow well setup) PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" MINIMUM SUCTION PIPE SIZE:  1-1/4" DRIVE PIPE SIZE:  1" DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.9 Amps on 115V / 4.95 Amps on 230V VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  3/4 MAXIMUM CAPACITY:  12 GPM FLOW at 10' LIFT and 40 PSI:  9.7 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  78 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP4822 Stainless Steel Shallow Well Jet Pump 3/4 HP Stainless steel shallow well jet pumps are heavy-duty, durable, corrosion resistant, high pressure and offer efficient non-stop operation for years. KEY FEATURES Superior performance at depths to water of 25' or less Heavy-duty, stainless steel pump housing for highest corrosion resistance Ready-to-install 230 volt motor - see manual for 115 volt conversion 1-1/4" NPT suction and 1" NPT discharge pipe sizes WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Stainless Steel HORSEPOWER:  3/4 MAXIMUM CAPACITY:  11 GPM FLOW at 10' LIFT and 40 PSI:  11 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  52 psi MAXIMUM INLET PRESSURE:   PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v MAXIMUM WATER TEMPERATURE:  122°F (50 °C)

Flotec FP4332 Thermoplastic Convertible Jet Pump 1 HP Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service. KEY FEATURES Superior performance at depths to water of 100' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor - see manual for 115 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1 MAXIMUM CAPACITY:  20.7 GPM (shallow setup) FLOW at 10' LIFT and 40 PSI:  18.3 GPM (shallow setup) MAX LIFT:  25' for shallow setup / 90' for deep setup MAXIMUM PRESSURE:  52 psi for shallow / 56 psi for deep PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DRIVE PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW:  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v   MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FPPSS3000 Cast Iron Pedestal Sump Pump 1/3 HP The pedestal design is engineered for the easy installation and replacement of most other brands of pedestal pumps. FEATURES Replaces any existing brand of 1/3 HP pedestal pump Long lasting cast iron construction Quick, easy installation Fits in a 12" diameter basin and offers a 1-1/4" discharge 2 year limited warranty BODY CONSTRUCTION:  Cast Iron Base with Stainless Steel Column HORSEPOWER:  1/3 MAXIMUM CAPACITY:  3480 GPH FLOW AT 10' LIFT:  2700 GPH SWITCH TYPE:  Vertical SWITCH ON LEVEL:  10-1/2" SWITCH OFF LEVEL:  2-1/2" MINIMUM SUMP DIAMETER:  12" MINIMUM SUMP DEPTH:  12" DISCHARGE PIPE SIZE:  1-1/2" FNPT MINIMUM PIPE SIZE:  1-1/4" MAXIMUM SOLID HANDLING SIZE:   CORD LENGTH:  6' AMP DRAW:  3.5 amps VOLTAGE:  115V, 60 HZ RECOMMENDED BREAKER:  15 amp LIQUID TEMP RANGE:  32°F to 70°F(0°-21°C) 

Flotec FPZS25T Submersible Thermoplastic Sump Pump 1/4 HP Flotec's 1/4 HP sump pump with energy-efficient design that produces high-output performance. Constructed from engineered composites providing dependable, corrosion-resistant service for years to come. Tethered on/off float switch.   Thermoplastic construction - resists corrosion Zinc motor housing - dissipates heat quickly and extends motor life Stainless steel fasteners and hardware - for long life Smooth Flow Hydraulics - delivers high performance for demanding applications   Switch Type: Tethered - Operates in 14" basins or larger Horse Power: 1/4 HP GPH: 3,200 Max Lift: 20' Solids Handling: 3/16" Discharge: 1.5" NPT Power Cord: 8', Grounded

Flotec FPP4322-08 Overhaul Kit Use with pump model FP4322 convertible jet pump Includes impeller, diffuser, and all seals and gaskets to overhaul pump Restores like-new performance

Flotec FPP1511-P2 Overhaul Kit Use with model FP4312 convertible jet pump Includes impeller, diffuser, and all seals and gaskets required to overhaul pump Restores like-new performance

Flotec FP4832 Shallow Well Jet Pump 1HP Flotec Shallow Well Jet Pump Stainless Steel Construction 1HP 115/230V 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 18.4GPM at 40psi Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8 GPM FLOW at 10' LIFT and 40 PSI:  6.4 GPM MAX LIFT:  25' MAX PRESSURE:  77 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.4 amps VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Tuthill 2C2B-C-7 Mechanically Sealed Pump Tuthill 2C2B-C-7, Cast Iron Rotary Gear Pump. Pump End Only. 8 GPM C Series. Cast Iron Construction NO motor. Flange mount. Clockwise rotation only (from shaft end view). Inlet Port is 1 inch NPT, Discharge Port is 1 inch NPT. Features : Pump Body:Cast Iron  Shaft Seal:Mechanical Seal Viton  Port Size:Inlet Port is 1 inch NPT Discharge Port is 1 inch NPT.

HYPRO 9203C CAST IRON PEDESTAL MOUNT PUMP The Hypro Cast Iron Pedestal Mount (9203C) pump model has a direct drive and a maximum free flow of 140 GPM. It has a maximum pressure of 180 P.S.I. as well as a maximum speed of 6,000 RPM.   Max. flow: 140 gpm/530 lpm (free flow) Max. pressure: 180 psi/12.4 bar (Shut off) Max. speed: 6000 rpm Max. fluid temperature: 140°C   Pedestal mount, direct drive Housing available: cast iron and stainless steel Port sizes: 1 ¼" NPT inlet, 1" NPT outlet Shaft: 5/8" solid Pump shaft rotation: CCW (9202S-R is CW) Impeller: glass-filled nylon (cast iron standard); glass filled polypropylene (stainless standard) Pump seals: Viton/ceramic standard (Life Guard silicon carbide, Buna-N ceramic and Viton/silicon carbide available) Life Guard silicon carbide standard in stainless steel pumps

Tuthill 2C2EN-C-7 Pump 9Gpm W/Outer Bearing Cast Iron Rotary Gear Pump Pump End Only 8 GPM C Series Pump Cast Iron Construction NO motor Ball Bearing on Shaft Clockwise rotation only (from shaft end view) Inlet Port is 1 inch NPT Discharge Port is 1 inch NPT

Tuthill CCI102017 Pump W/Vtn Seal 56C Cast Iron Rotary Gear Pump Pump End Only, 20 GPM CC Series Pump Cast Iron Construction Nema frame size is 56C Inlet Port is 1-1/2 inch NPT Discharge Port is 1-1/2 inch NPT