|
|
181.22 |
|
|
BURKS 9915, WEAR RING BRONZE
UNSPSC Code: 40150000
|
109.40 |
|
|
|
55.25 |
|
|
|
104.98 |
|
|
BURKS 20CS6M Close Coupled Turbine Pump
BURKS exclusive unique regenerative type turbine pumps. Designed to handle clear water in addition to and many other non-abrasive, lower viscosity liquids on high pressure. As well as low capacity applications with the greatest possible efficiency.
BURKS is the only turbine pump with Life-Lok® External Impeller Adjustment. This feature allows re adjustment of impeller without disturbing piping, disassembling pump or replacing parts. This, as a result, gives up to 40% longer service life than turbine pumps of other designs.
Self-Priming Pump
Compact and Space-saving size
No coupling so this eliminates misalignment problems
Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C).
Bronze impeller with Monel blades, therefore the only moving part
Bronze raceway with cast-in vortex pockets – will not vapor lock
#303 Stainless Steel pump shaft
Every pump is factory tested
Motor Information
4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and therefore Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.
CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor
start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.
High Temperature
For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications.
|
3161.06 |
|
|
BURKS 22850-6, Wet End Kits for Series CR6M Pumps
Repair Kit for All 3CR6M, A3CR6M Series Pumps. Kit Includes: Impeller, Raceway, Shaft Seal, O-Ring Gasket, Impeller Locknut, and instructions.
|
728.28 |
|
|
BURKS 10CS5M, Turbine Pump 32.5 gpm 115/230v
Burks close coupled 32.5 gpm turbine pump having 1-1/4" NPT inlet size and 1" NPT outlet size features 350 ft Maximum Head and maximum suction lift and 1 hp power rating.
Burks exclusive unique regenerative type turbine pumps are designed to handle clear water and many other non-abrasive, lower viscosity liquids on high pressure, low capacity applications with the greatest possible efficiency.
Compact space saving size
No coupling - eliminates misalignment problems
Dependable carbon ceramic mechanical shaft seal for temperatures to 225 deg F (107 deg C)
Bronze impeller with monel blades - the only moving part
Bronze raceway with cast-in vortex pockets - will not vapor lock
303 stainless steel pump shaft
Easy to service
Every pump factory tested
|
2820.38 |
|
|
BURKS 24CT7MJAB, Turbine Pump 8gpm 1" NPT Ports 115/230VAC
Burks close coupled 8 gpm turbine pump having 1" NPT inlet size and 1" NPT outlet size features 350 ft Maximum Head and maximum suction lift and 1/2 hp power rating.
|
4574.70 |
|
|
BURKS 30WA6, Centrifugal Pump 115/230v 3HP
Burks 30WA6 Centrifugal Pump, Self Priming, 60 Hz, Single Phase, 3500 RPM, 3 Horsepower, ODP Motor Enclosure.
Close Coupled to a 3 Horsepower 115/230 Volts motor
Bronze Fitted Cast Iron Construction w/ Plastic Impeller.
Ports are 1-1/2 Inches NPT Inlet, 1-1/2 Inches NPT Outlet.
Please contact us for a shipping quote at http://www.clrmarine.com/Contact_Us
|
2650.46 |
|
|
BURKS 310G5-1 1/4, BURKS CIRCULATION G5 PUMP 230-440V 1HP 3PH
Centrifugal Pump and Motor unit. Bronze Fitted Cast Iron Construction. Close Coupled to a 1 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.25 Inches.
|
1605.60 |
|
|
BURKS 315CS6M TURBINE PUMP 230/460 Volts 1.5HP
All BRONZE Construction.
Close Coupled to a 11/2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor.
Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
Self-Priming Pump
Compact and Space-saving size
No coupling so this eliminates misalignment problems
Dependable carbon/ceramic mechanical shaft seal for same temperatures to 225 °F (107° C).
Bronze impeller with Monel blades – therefore the only moving part
Bronze raceway with cast-in vortex pockets – will not vapor lock
#303 Stainless Steel pump shaft
Easy to service as a result
Especially relevant, Every pump factory tested
Motor Information
4CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 1750 RPM and Three Phase motors are 208-230/460 Volts, 60/50 Hz, 1750/1450 RPM.
CS Series: Single Phase motors are 115/208-230 Volt, 60 Hz, 3450 RPM Three Phase 1, 11/2 & 2HP. – 208-230/460 Volt, 60/50 Hz., 3450/2900 RPM Three Phase 3 & 5 HP – 208-230/460 Volt, 60 Hz, 3450 RPM Standard pump motors have open drip proof construction and are rated with jet pump service factors for continuous duty operation at all ratings shown. Single phase motors are capacitor start/induction run with built-in overload protection. Three phase motors require a magnetic type starter which provides full 3-leg overload protection. Failure to use the correct starter and overloads will void the warranty.
High Temperature
For Temperatures to 500 °F (260 °C). Series CS Pumps are available while in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications.
For High Temp Models please use the Contact Us page, also use the Contact Us page for a Shipping Quote.
|
2882.48 |
|
|
BURKS 3CR6M, Turbine Pump 230VAC
Burks 3CR6M Turbine Pump.
Close Coupled 230 Volts 60 Hz, Single Phase, 3450/2850 RPM, 1/3 Horsepower.
ODP Motor Enclosure.
UNSPSC Code: 40150000
|
1574.10 |
|
|
BURKS A3CR6M, Turbine Pump 4 gpm 230v
Application: Carpet Cleaning Machines, Small Steam Generators, Solar Heating Systems, Booster Pump, Injector Venturi Operation, Cleaning and Flushing
Frame/Raceway : Bronze
Impeller : Bronze (Monel Blades)
Shaft : #316 Stainless Steel
Front Cover : Bronze
Shaft Seal : Carbon-Ceramic / S. Steel / Buna-N
MAXIMUM OPERATING CONDITIONS
TEMPERATURE (For Standard Buna-N Seal) : 225°F (107°C)
INLET PRESSURE : 50 PSI (344kpa)
CASING WORKING PRESSURE : 150 PSI (1034kpa)
VISCOSITY : 200 SSU
FEATURES
• Compact Size-Ideal for OEM Applications
• All Bronze Construction with Monel Impeller Blades
• Carbon/Ceramic Shaft Seal for Temperatures to 225°F (107°C)
• #316 Stainless Steel Shaft
• Close Coupled Design - No Couplings or Alignment Problems
• Motors have ball/ball bearing construction and open ventilated enclosure. Motors are NOT drip-proof. Rated for continuous duty operation at all ratings shown.
• Capacitor Start Motors Have Built-In Automatic Overload Protection
• Furnished with UL Recongnized Motor Lead
• Field Adjustable Impeller for Extented Service Life
Motors have ball bearing construction and open ventilated enclosure. Motors are NOT drip-proof.
Compact size: only 10 1/2" long x 4" wide x 6 1/4" high.)
UNSPSC Code: 40150000
|
1574.10 |
|
|
BURKS T37CT7MV, TURBINE PUMP 60 VOLTS 3PH 3/4HP
Bronze Fitted Cast Iron Construction.
Seal and O-ring are VITON.
Pump is close Coupled to a 3/4 Horsepower , 3450 RPM, 208-230/460 HZ , 60 Volt, 3 Phase, TEFC Motor.
Ports are 1 Inches NPT Inlet, 1 Inches NPT Outlet.
UNSPSC Code: 40150000
|
2388.60 |
|
|
BURKS 10CS6M, TURBINE PUMP 115/230v 1PH 1HP BF
Close Coupled to a 1 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor.
Ports are 1-1/4 Inches NPT Inlet, 1 Inches NPT Outlet.
|
2568.53 |
|