March Mag-Drive Centrifugal Pumps Bronze Center Inlet 12VDC 5.5GPM     The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March 815-PL Beer Pump March Pump's 815-PL Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7 gallons per minute at 4.5 feet, and its maximum head is 18.6 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The 815-PL Beer Pump motor has a six foot cord, a plug, and a base.  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   The 815-PL Beer Pump pumps Hot Water and Hot Wort.     Unit System 60Hz 50Hz Max Flow 7 GPM 22.7 LPM Max Head 18.6 FT 4.1 M Power .04 HP .029 KW Electrical 115V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"MPT Outlet 1/2"MPT Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller) Can handle liquids of 250F Materials are FDA Food Compliant With 6 Foot Cord and Plug Components are UL Recognized American Made    

March Pump's AC-5B-MD Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for homebrewing. It is capable of generating a maximum flow of 17 gallons per minute at 1 foot, and its maximum head is 27 Feet (or around 11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 225 Fahrenheit or 107 Celsius.  The AC-5B-MD Beer Pump pumps Hot Water and Hot Wort.     Unit System 60Hz 50Hz Max Flow 17 GPM 60 LPM Max Head 27 FT 6 M Power .125 HP .093 KW Electrical 115V 60Hz   Type Metering Pump Inlet 1"FPT Outlet 1/2"MPT Wet End Polysulfone (Front and Rear Housing, Impeller), Stainless Steel (Magnet Shell, Shaft), Buna N (O-Ring), Ceramic (Thrust Washers) Can handle liquids of 225F Materials are FDA Food Compliant American Made Components are UL Recognized    

March 809 BRC HS 12VDC Mag-Drive Pump March Mag-Drive Centrifugal Pumps Bronze 12VDC High Speed 5.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC High Speed 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March 809 BRC HS 24VDC Mag-Drive Centrifugal Pumps Bronze 24VDC High Speed 5.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 24VDC High Speed 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March 809 815 Series Mag-Drive Centrifugal Pumps Bronze Center Inlet 115V 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.     March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pumps Bronze 115V High Speed 4.5GPM     The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March Mag-Drive Centrifugal Pumps Bronze 230V High Speed 4.5GPM   The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated. • Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 230V High Speed 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet  

March 809 BR 12VDC Applications for the 809-BR 12V & 24V Magnetic Drive Pump include hot water systems, refrigeration systems and solar heating.   March Pump's industrial 809-BR 12V & 24V is an American seal-less centrifugal magnetic drive pump ideal for applications such as hot water systems. It is capable of generating a maximum flow of 5 gallons per minute at 1.5 feet, and its maximum head is 7 Feet (or around 3PSI). The standard wet end (the materials that come into contact with the solution) is composed of Bronze, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 0.01 Horsepower DC Brush Type Motor, available in 12 or 24 Volts.  The 12 Volt motor has an operating range from 0 to 14 Volts, and the 24 Volt motor has an operating range from 0 to 26 Volts. The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.   Max Flow 5 GPM 18.9 LPM Max Head 7.1 FT 2.1 M Power .01 HP .007 KW Electrical 12V Range 0-14 or 24V Range 0-26  

March 809 BRC 24VDC Pump Center Inlet Low Speed

March 140 Series Mag-Drive Centrifugal Pumps     • Use the compact Series 140 pumps where maximum flow with minimal pressure is desired. Maximum flow is 12.5 GPM (55 LPM) and maximum head is 11.5 ft. (2.5m) • Series 140 pumps use Open Frame Skeleton Type Motors or 1/20 HP (.037 kw), 2900 rpm 115 volt air-cooled motors. • Materials used are glass-filled polypropylene, Buna N rubber, ceramic, Ryton®, Teflon® and Viton®. • Maximum Liquid Temperature is 190 degrees F     March Pump Mag-Drive Centrifugal Pump 230V Open Frame Skeleton Motor 12.5GPM 1 1/8" Hose Inlet, 7/8" Hose Outlet  

Applications for the  March 1C-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.      March Pump's industrial 1C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless steel, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 0.25 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 1/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, SJT Cord  

Applications for the March 1U-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   March Pump's industrial 1C-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless steel, and Ceramic Magnet.  When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 0.25 inch male pipe thread, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1C-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 1/4"MPT Outlet 1/4"MPT Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, SJT Cord  

Applications for the 1U-MD Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.    March Pump's industrial 1U-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI).  The 1U-MD pump must be used submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, Cycolac, Delrin, and Ceramic Magnet.  When submerged, Epoxy, Noryl, Cycolac, Delrin, and the SJT Cord are also in contact with the solution. The inlet connection is a screen, and the outlet is 0.25 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1U-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes     Type Centrifugal Mag Drive Inlet Screen Outlet 1/4"MPT Wet End Polypropylene (Rear Housing), Buna N (O-Ring), Nylon (Impeller), Cycolac (Cover), Carbon/Teflon (Thrust Washer), Delrin (Screen), 316 Stainless Steel (Shaft), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Noryl, Cycolac, Delrin, SJT Cord    

Applications for the March AC-5C-MD Magnetic Drive Pump include chemical recirculation, refrigerators, small scrubbers, detergent mixers, computer cooling, carbon arc furnace cooling, and marine air conditioners.    March Pump's industrial AC-5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (or around 11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 17 GPM 60 LPM Max Head 27 FT 6 M Power .125 HP .093 KW Electrical 115V 50/60HZ or 230V 50/60HZ     Type Centrifugal Mag Drive Inlet 1"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Buna N (O-Ring), Ceramic (Shaft, Thrust Washers), Ceramic Magnet Available with 750 Priming Chamber