Backing Plate for 80 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series. Features: Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA) 316L cast stainless steel 4-1/4" x 6" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Backing Plate for 70 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series. Features: Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Replacement liner for 80 series in-gunnel rod holder, 11" long, cut to desired angle and length. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Single Aluminum 5° Transom Mount Rod Holder The perfect way to add rod holders to the transom area. Designed with outboard engine wells in mind. An ideal way to add rod holders to a seating station. These rod holders feature a super strong 3/8" thick blade, rugged welded 1/3" tallgimbal bar, and a 1-5/8" inside diameter with a flared opening to make it easy to insert a rod in the holder. The taper liner and the addition of a rod security hole in the blade ensures that your valuable rods are protected. Mount vertically or with some outward angle for a wider fishing spread. Tube leans 5° away from the 3" tall x 2-3/4" wide mounting base. 10" overall height. Includes white vinyl liner.

Replacement Liner for 70 Series - White Replacement liner for 70 series in-gunnel and clamp-on rod holders. This UV-resistant vinyl liner protects rods. Features: Recessed liner (doesn't come to the top of the tube) Made of white vinyl material

Aluminum Horizontal Clamp-On Rod Holder OD - White Powder Coated with Sleeve C.E. Smith's line of white powder coated clamp-on rod holders offer a great alternative to stainless steel. These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Horizontal Fits rails with 1.66" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Adjustable Mid Mount Rod Holder - 7/8" or 1" OD - White Powder Coat Aluminum with Sleeve & Hex Key C.E. Smith's line of white powder coated clamp-on rod holders offer a great alternative to stainless steel. These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Adjustable Mid Mount Fits rails with 7/8" or 1" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Adjustable Mid Mount Rod Holder - 1.66" or 1-1/2" OD - White Powder Coat Aluminum with Sleeve & Hex Key C.E. Smith's line of white powder coated clamp-on rod holders offer a great alternative to stainless steel. These rod holders are constructed of marine grade aluminum that has been 100% anodized for functionality and style. Features: Style: Adjustable Mid Mount Fits rails with 1.66" or 1-1/2" measured OD Made from Marine Grade Aluminum WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

53696 Rod Safety Ring Attach the C.E. Smith Rod Safety Ring to the bottom of rod holders and stop worrying about dropping your equipment.   Made to secure into the 0.5" drain hole found at the bottom of the flush-mount cast-bottom rod holder from C.E. Smith, the rod safety ring gives you a convenient place for you to tether your rod and reel, boat fender, or any other valuable you don't want to fall overboard.  Features: Provides a convenient place to secure rods 316L Marine-grade stainless steel Quick and easy installation *Sold as an Individual

Black 40" Post Guide-On & FREE Camo Wet Lands Guide-On Pads This kit includes two C.E. Smith 40" Black Post Guide-Ons and two Camo Wet Lands Post Guide-On Pads. C.E. Smith Trailer Post Guide-Ons give a clear visual marker to know you're backing, loading, or unloading your boat trailer evenly and properly to avoid costly damage. Unlike plastic guide-ons that fall apart or break with minimal impact, C.E. Smith Post Guide-Ons boats square 16 gauge steel uprights, pre-galvanized for corrosion resistance, and 2-3/8"-dia. Black PVC posts, to stand up strong season after season.  While the camo post-guide-on pads, are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter). Features: Provide a clear marker for backing, loading, or unloading your boat trailer 16 gauge square steel uprights Pre-galvanized construction for corrosion resistance 2-3/8" black PVC posts Built to last season after season 40" tall The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end  Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post-guide-on covers: Camo Wet Lands Kit Includes:  Part 27626: C.E. Smith Black 40" Post Guide-Ons Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Black PVC Post Guide-On & FREE Camo Wet Lands Post Guide-On Pads This kit includes two 60" Black PVC Post Guide-Ons and two Camo Wet Lands Post Guide-On Pads. The C.E. Smith Trailer Post Guide-Ons give a clear visual marker to know you're backing, loading, or unloading your boat trailer evenly and properly to avoid costly damage. Unlike plastic guide-ons that fall apart or break with minimal impact, C.E. Smith Post Guide-Ons boats square 16 gauge steel uprights, pre-galvanized for corrosion resistance, and 2-3/8"-dia. Black PVC posts, to stand up strong season after season. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Provide a clear marker for backing, loading, or unloading your boat trailer 16 gauge square steel uprights Pre-galvanized construction for corrosion resistance 2-3/8" black PVC posts 60" Overall Height Mounting brackets and metal uprights allow for 19” of adjustment on each side of the trailer frame. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27646: C.E. Smith 60" Black PVC Post Guide-On  Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

Sidewinder Backing Plate f/Bolt-In Holders Below top operation. Fully locked in Running and 80° out Trolling positions. Locks when handle is up or down. Rotates when handle is to the left or right. Fastest Lay-Down on the market. Automatically locks in position when raising or lowering the pole. No knobs to loosen or tighten. Just pull down the Ridged Collar and lower or raise the pole. Available with Quick Laydown or Curved Tube. No ball bearings to rust. Internal Delrin and nylon bearing surfaces provide smooth operation and prevent metal to metal contact. Accepts our 16Ft Extra Strong (AP3916XS) or 18Ft (AP3918) Outrigger Pole. Has 4"x6" Mounting plate. Extends 14" above and 8-1/2" below mounting plate. Fits all outrigger ready boats.

40" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 40" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features: Mounting hardware and wiring included  40" Total Height Adjusts Out to 13" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" sq. 16 ga Pre-Galvanized Steel post Extends 18" Into 2" PVC tube for strength Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized  The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27740: C.E. Smith 40" Post Guide-On With LED Lighted Posts   Part 27902: C.E. Smith Post Guide-On Pad - 36" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

60" Post Guide-On with L.E.D. Posts & FREE Camo Wet Lands Post Guide-On Pads The kit includes two 60" Post Guide-Ons With L.E.D. Posts and two Camo Wet Lands Post Guide-On Pads. The Post Guide-Ons allows you to see the location of your trailer when it's underwater. Equipped with long-lasting, waterproof, and shockproof, one-piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. The camo post-guide-on pads are used to protect the boat finish from scuffs. They are sized for a close fit on standard 2" schedule 40 PVC posts (2-3/8" actual outer diameter).  Features:  Mounting hardware and wiring included  Adjusts Out to 19" on each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" square, 16 gauge pre-galvanized steel uprights that are 39" high 2-3/8" diameter white PVC posts Stands 60" above the trailer frame Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized The galvanized coating is very thin (0.45 oz. on each side) The cover-pads are made from strong polyurethane-coated 600D nylon fabric Covers have nylon closures on each end Open the bottom and top of the cover-pads to allow LED guide on lamps Covers contain a 1/2" thick closed-cell polyurethane foam inner pad Color of post guide-on covers: Camo Wet Lands Kit Includes: Part 27760: C.E. Smith 60" Post Guide-On With L.E.D. Posts Part 27903: C.E. Smith Post Guide-On Pad - 48" - Camo Wet Lands  Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width *Sold in pairs

C.E. Smith Company C. E. Smith Company, Inc. was established as a manufacturing firm producing precision metal stampings, fabrications and assemblies for a broad variety of industries. Stainless steel boating and fishing products are sold under the SMITH TM trademark. The line includes an adjustable, completely stainless steel t-top, fiberglass electronic boxes, t-top storage bags navigation lights and antenna bracket.