SI-TEX 307/50/200T Transducer f/CVS-832 Dual Frequency 50/200 kHz Max Power: 1kW Beam Angle: 22 x 45 deg. @ 50 kHz, 6 x 11 deg. @ 200 kHz Housing: Bronze Mount: Through Hull Plug: 8 pin Cable: 30' Temp: Yes Speed: No For SI-TEX model: CVS862, 832C, 833C, Genesis

SI-TEX 300/50/200T Bronze Thru-Hull Transducer Dual Frequency 50/200 kHz Max Power: 600W Beam Angle: 43 deg. @ 50 kHz, 9 deg. @ 200 kHz Housing: Bronze Mount: Through Hull Plug: Two 8 pin Cable: 30' Temp: Yes Speed: No For SI-TEX model: CVS208/209

120kHz Bronze Thru-Hull Transducer f/SDD-110  Features: 120kHz Bronze Thru-Hull Transducer Specifically for SI-TEX SDD-110

707/50/200T-CX Bronze Thru-Hull Transducer 1kW, Bronze with temp recommended for deep water use (Beam angle: 14' x 21' @50kHz, 3' x 5' @200kHz)

SI-TEX706/50/200T Bronze Thru-Hull Trandsucer Dual Frequency 50/200 kHz Max Power: 1kW Beam Angle: 14 x 20 deg. @ 50 kHz, 7 deg. @ 200 kHz Housing: Bronze Mount: Through Hull Plug: Two 8 pin Cable: 30' Temp: Yes Speed: No For SI-TEX model: CVS208/209/210/211

Thru-Hull Transducer SI-TEX Thru -Hull Transducer for the SVS-650, CVS-126 and CVS-128

1700/50/200T-CX Transducer Bronze thru-hull transducer with temp only (Beam angle: 45 degrees @ 50kHz, 11 degrees @ 200kHz) w/30'cable attached to the transducer.

Bronze Thru Hull Transducer Bronze Thru-Hull Transducers are for large boats and for boats with in-board motors that make typical Transom Mount Transducers ineffective. They are not recommended for trailered boats as the transducer is not flush with the hull. Bronze Thru-Hull Transducers require that a hole be drilled in the hull and the shaping of a fairing block. Professional installation is recommended. Plastic Thru-Hull Transducers are an alternative to Bronze Thru-Hull Transducers. Description: Bronze thru hull transducer, single or dual beam use. 20/60 degree, 200/83kHz. Transducer dimensions: 5.25L X 2.75"W X 1.2"D (below hull); Shaft diameter: .86". Fairing block not included. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B175MW Med Ultra Wide 1kW, 20° Chirp Thru-Hull Transducer f/12-Pin Garmin175MW Med Ultra Wide 20 Degree, 1KW Chirp Thru-hull Transducer with 12 Pin Connector for Garmin  Airmar's innovative transducer designs have revolutionized the fishing world, and they continue to do so with the Chirp-ready B175 Medium Ultra-Wide (MW) Tilted Element™ Thru-hull transducer. The B175MW takes transducer design and performance to a whole new level by using medium frequency (60-100 kHz) with an incredible ultra-wide beamwidth ranging from 57-73° port-starboard to 16° average fore-aft. Maximum coverage under the boat is achieved with this medium-frequency transducer, serving anglers who target pelagic species in the upper water column. Airmar’s Medium Ultra-Wide models are perfect for seeking deeper species with a frequency band from 60-100 kHz. When paired with our other popular models such as the B275LHW, provides the angler with a broad set of frequencies (Low, Medium-Wide, High-Wide) to interrogate targets from deep to shallow. The B175MW Tilted Element Thru-hull is a 1 kW transducer housed in one of AIRMAR’s most popular Tilted Element housings which includes a ceramic element fixed at a 20° angle. Because the transducer is installed almost flush with the hull, the tilted element corrects for the hull deadrise and orients the ceramic element vertically to ensure maximum echo returns to the transducer. Features: Fixed 20° tilted version for 16° to 24° hull deadrise 12 Pin Connector for Garmin FishFinders Depth and fast-response water-temperature sensor 1 kW with depth tracking down to 400 m (1,300#39;) Medium frequency: 60-100 kHz 57° to 73° beamwidth (port/starboard) 16° average fore/aft 40 kHz of total bandwidth from one transducer Medium frequency for superior mid-depth performance and excellent fish-target separation Bronze housing for use on stepped, planing, or displacement hull Low-profile, thru-hull housing yields good resolution at speed when installed properly Exclusive Xducer ID® technology Specifications: Brand: Airmar Technology Acoustic Window: Urethane Cable-Length: 9 m (30'), 10 m (33') Common Use: Fishing Connector: Garmin 12-Pin Country of Origin: USA Display Connector: 12G Functions: Depth, Temperature Hole Size: 95 mm (3-3/4") Hull Material: Fiberglass or wood Material: Bronze Max Deadrise Angle: 24° Max Depth: 400 m (1300') Max Vessel LOA: Up to 11 m (36') Medium Frequency: 60-100 kHz Medium Frequency Beamwidth: 57° to 73° (Port/Starboard) X 16° average (Fore/Aft) Medium-Wide Beamwidth: 57° to 73° beam p/s 16° average f/a Mounting Style: Tilted Element Thru-Hull Power Rating: 1 kW Single or Dual Frequency: Single Tilt Angle: 20° Tilted Element: Yes Water Temperature: -10° to 40°C (14° to 104°F) Weight: 2.7 kg (6 lbs.) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B117 Bronze Thru-Hull Transducer w/Humminbird #9 Plug - 7-Pin The B117 features our 50/200 kHz, dual-frequency, single ceramic element in a low-profile housing. The nearly-flush design minimizes drag with only 5mm (3/16") extending outside of the hull. The plastic P319 and stainless steel SS60 models are also available to accommodate all hull materials. Features Industry standard for low-profile transducers Depth and temperature Good target detail in shallow-water at 200 kHz and good deep-water bottom tracking at 50 kHz Right angle cable exit offers low headroom and protection when transducer is stepped on Included rubber washer allows tightening of the hull nut to irregular hull surfaces Housings are ABYC H-27 compliant Optional temperature sensor Bronze transducer housing Boat Size: 8M (25') and up Specifications: Weight: Bronze - 0.9 kg (2.0 lb) Hull Deadrise: Up to 8° Acoustic Window: Urethane Hole Diameter: 51mm (2") This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RealVision 3D™ Bronze Thru-Hull Transducer Pair Pack - 20° - 8M Cable & Y-Cable Designed for inboard or outboard boats, the RV-220 Bronze Through Hull Transducer System lets you easily identify structures and locate fish with the life-like clarity of RealVision 3D™ sonar. The RV-220 system is a 4-channel, Wide Spectrum CHIRP transducer system with DownVision™, SideVision™, high frequency CHIRP fish targeting and RealVision 3D™ sonar inside. The transducer system has a built-in attitude and heading reference system (AHRS) that stabilizes the sonar imagery, automatically compensating for vessel motion. You’ll enjoy crystal-clear imagery in waves, swells, and while maneuvering. The RV-220 system also has a built-in fast response water temperature sensor for quick, accurate readings. Raymarine’s RV-220 Bronze Through Hull Transducer system pack contains a pair of RealVision 3D transducers with internal offset to accommodate hull deadrise angles from 13° to 20°. This completely eliminates the need for fairing blocks. The low-profile design slips effortlessly through the water without causing drag or cavitation. The near-flush RV-220 system works great on trailered boats too. The RV-220 system features rugged cast-bronze through hull bodies suitable for fiberglass or wooden hulls. One transducer transmits and receives to port and downwards, the other to starboard and downwards, ensuring a full 180° of underwater coverage even on boats with deep keels or other underwater protrusions. Each transducer features a 2M pigtail, joining y-cable and 8-meter extension cable, resulting in an overall cable length of 10M (33'.) What’s in the Box? RV-220P Bronze Port Transducer with 2M cable RV-220S Bronze Starboard Transducer with 2M cable RealVision 3D Transducer Y-Cable RealVision 3D 8M (26') Transducer Extension Cable Anti-rotation bolt kit Installation instructions

B275LH-W Bronze Thru-Hull Transducer - 12-Pin Get more coverage under your boat with Airmar’s unique wide beam, high frequency Chirp-ready transducers. The high band operates across a frequency range of 150 to 250 kHz and has a fixed 25° beam for all frequencies. The high frequency band results in superior resolution. The constant wide beamwidth provides twice the coverage under the boat and excellent fish arches on the display compared to most high frequency narrow beam transducer options. The included high-performance fairing improves broadband performance at speeds over 30 knots (34 MPH). The high wide is the ideal choice for both inshore and pelagic fishing, where resolution and maximum coverage under the boat are essential down to 500'. The low frequency band and 1 kW of power also provides great deeper water performance. Get the best of both worlds with Airmar’s dual frequency Chirp-ready transducers with wide beam coverage. Features: Depth and fast-response water-temperature sensor 1 kW for great deep water performance from the low frequency Low Frequency: 42 kHz to 65 kHz with maximum depth of 914 m (3000') 25° to 16° beamwidth High Frequency: 150 kHz to 250 kHz with maximum depth of 152 m (500') 25° constant beamwidth 123 kHz of total bandwidth from one transducer Covers popular fishing frequencies of 50 and 200 kHz plus everything else in the bandwidth High frequency provides superior shallow water performance, bottom detail and fish target separation High wide beamwidth provides more coverage under the boat for detecting fish in the upper water column Bronze transducer housing with high-performance fairing for optimal performance at higher speeds Recommended boat size: 8 m (25') and above Hull Type: Fiberglass or wood Exclusive Xducer ID® technology WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Bronze Thru-Hull Transducer w/ Temp, 600w (10-Pin) 600 Watts 50/200 kHz 45/15 degree Beam Angles Bronze Thru-Hull with Temperature 30 Foot Cable with 10-Pin Connector WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B164 Bronze Thru-Hull Transducer w/Humminbird #9 Plug - 7-Pin - 0° Step up to a 1kW - Without a Fairing! Airmar has taken our innovative Tilted Element™ technology to a higher power. The 1kW, flush-mount, Tilted Element transducer is perfect for fast, trailered, tournament sportfishing vessels that cannot have a High-Performance Fairing. The flush-mounted, bronze housing protrudes less than 6.35 mm (0.25") outside your hull and can sit on trailer rollers and bunks with no damage at all. The ceramic arrays are tilted inside the housing giving you the perfect vertical beam with maximum energy on what is directly below your boat. Take your fishfinder to the next power with this 1kW, Tilted Element transducer. Features: 1 kW power, 50/200 kHz multiple-ceramics Engineered for center-console and trailered boats Low-profile protrusion below the hull No affect on your boats running performance Interfaces to any 600W or 1 kW echosounder Bronze transducer housing Depth and fast-response water-temperature sensor Boat Size: 8M to 11M (25' to 35') Specifications: Weight: 2.7 kg (6 lb) Hull Deadrise: Up to 28° Acoustic Window: Urethane This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B164 Bronze Thru-Hull Transducer w/Humminbird #9 Plug - 7-Pin - 12° Step up to a 1kW - Without a Fairing! Airmar has taken our innovative Tilted Elementâ„¢ technology to a higher power. The 1kW, flush-mount, Tilted Element transducer is perfect for fast, trailered, tournament sportfishing vessels that cannot have a High-Performance Fairing. The flush-mounted, bronze housing protrudes less than 6.35 mm (0.25") outside your hull and can sit on trailer rollers and bunks with no damage at all. The ceramic arrays are tilted inside the housing giving you the perfect vertical beam with maximum energy on what is directly below your boat. Take your fishfinder to the next power with this 1kW, Tilted Element transducer. Features: 1 kW power, 50/200 kHz multiple-ceramics Engineered for center-console and trailered boats Low-profile protrusion below the hull No affect on your boats running performance Interfaces to any 600W or 1 kW echosounder Bronze transducer housing Depth and fast-response water-temperature sensor Boat Size: 8M to 11M (25' to 35') Specifications: Weight: 2.7 kg (6 lb) Hull Deadrise: Up to 28° Acoustic Window: Urethane This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.