AMT Pump 5760-95 1Hp 2"Npt 115V CI-SS Submersible Shredder Sewage Pump 5760-95, 130 GPM, 1.0 HP, Carbide Tipped Cast Iron construction with stainless steel motor housing 1.0 HP, 14 Amps, 115 volts, continuous duty, single phase electric motor Can handle solids up to 1 inch Triplex seal system 2 inch output port with a discharge rate of 7800 gallons per hour The AMT by Gorman-Rupp 5760-95 is an industrial grade shredder sewage pump that is designed to handle sludge and dirty water applications.  Features an enhanced spiral shredder mechanism plate and carbide tipped impeller to prevent clogging when pumping sludge type waste.  Liquid content still must be above 85% to keep from damaging the pump and possibly void the warranty.

Yamada NDP-50BFN NPT NEW Pump (852837)2" Npt Ci/Buna NDP-50BFN AIR POWERED DOUBLE DIAPHRAGM AODD PUMPS Yamada® NDP-50BFN series Air Powered Double Diaphragm (AODD) pumps provide a maximum flow rate of 166 gallons per minute. Pumps are available in aluminum, stainless steel (316), cast iron, polypropylene, and Kynar construction, with a wide variety of diaphragm materials. Inlet (in)2 Outlet (in)2 Max Flow (gpm)164.0 Max Temp180 Max Solid (in)5/16 Valve Type (in)3/4 Air Motor MaterialAluminum Body MaterialCast Iron Elastomer MaterialBuna N

IWAKI MD-15RT-115NL, POLY MAG DRIVE PUMP 1/2" THREAD Mag Drive Centrifugal Pump and Motor Assembly, GFRPP Polypropylene Construction, close coupled to a 1/75 Horsepower, 115 Volts AC, 1 Phase Electric Motor. 1/2 Inch NPT Threaded Port Connections.

AMT Pump MSV3-5-1P Multistage Mtr/Pmp 1Hp 115v Multi-Stage Booster Pump – MSV3-5-1P, 5-Stage, 115-208-230 Volts NEMA 56C, Dual Cycle 50 and 60 Hz, 1.0 HP, single phase, Totally Enclosed, Fan Cooled motor Recommended to operate at or below the Best Efficient Point which is at 16 GPM and a Max Total Head of 105 feet Cast Iron base and adapter 1 inch NPT cast iron flanges 304 series stainless steel components with Teflon wear rings EPDM-Tungsten Carbide Seal that is easy to remove and replace The AMT MSV3-5-1P is a non-self-priming/gravity feed, industrial pump with high pressure and low output.  This unit is more commonly referred to as a jockey pump and is often installed for water transfer uses where no suction lift is required such as boiler feed, condensate return, high pressure washdown, irrigation, booster service, and fire protection/sprinkler systems.  These pumps have NOT been investigated for use in drinking water systems.  

Amt 5764-95 Sub Shredder Pump 3" Npt SUBMERSIBLE SHREDDER SEWAGE PUMP   Cast Iron with Stainless Steel Motor Housing Carbide-Tipped Shredder Impellers Spiral Shredder Mechanism Plate Surface Hardened for Enhanced Cutting Ability Silicon Carbide Lower Seal 3" NPT Port Sizes Max. Temperature 104° F  3 HP 230 Volt     AMT Submersible Shredder Sewage pumps feature an enhanced spiral shredder mechanism plate and carbide tipped impeller to prevent clogging and reduce maintenance when cutting through stringy, fibrous and sludge type waste. Applications include sewage pumping stations, septic tanks, sewage treatment plants, dirty water drainage, flood and emergency. Also ideal for grinder type solids reduction application. Motors are rated continuous duty and single phase models have thermal overload protection.   AMT Submersible Shredder Sewage Pumps are reliable, cost effective and low maintenance.    

AMT 3201-96, Laundry Tray Pump 1/4 HP 115V GENERAL PURPOSE LAUNDRY TRAY PUMP   Cast Aluminum Construction Buna-N Mechanical Seal and O-Ring 1-1/4" NPT Suction and Discharge Port Self-cleaning, Semi-open Impeller Continuous Duty Motor 1725 RPM, 1/4 HP 115VAC Single Phase Open Drip Proof (ODP) 48Z Frame   The AMT Laundry Tray pump is a single stage, multi-vane open impeller unit. It is designed as a laundry tray pump but can be used for most gravity fed general service pumping applications. The open impeller design makes it particularly adaptable to dirty as well as clean liquids and is inherently resistant to clogging. The AMT Laundry Tray pump is readily available “Off-the-Shelf” for fast 24 hour shipment. For use with non-flammable liquids compatible with pump component materials.

AMT 4230-97, Coolant Recirculating Pump 1 Phase, 115V, 3/8" NPT Female 3/8" BRONZE COOLANT RECIRCULATING PUMPS   Cast Bronze Construction No Bottom Bearing!!! Brass Column and Impeller Shaft Bronze Self-cleaning Open Impeller 3/8" NPT Discharge Port Maximum Flow 8 GPM Maximum Head 10 ft. Available with 115V AC Single Phase or 230V AC Three Phase Motors,1590 RPM 1/25 HP Totally Enclosed Fan Cooled (TEFC) Motor Delivers up to 8 GPM and 4 PSI   The AMT Bronze Coolant/Recirculating pump has been manufactured for a wide variety of Industrial/Commercial Coolant and Recirculating applications. The absence of a bottom bearing makes the unit ideal for handling erosive liquids. A 36" 3-conductor power cord is included. AMT Bronze Coolant/Recirculating pumps are reliable, cost effective and low maintenance. Many are readily available “Off-the-Shelf” for fast, 24 hour shipment. For use with non-flammable liquids compatible with pump component materials.  

Amt 3693-013-09 Impeller For Am 3693-95/97  

Amt 4891-010-09 Impeller For Am 4891-95/97  

Amt 4901-010-09 Impeller For Am 4901-95/97  

Amt 5351-95, Cast Iron Coolant Pump 230/460volt  INTERCHANGEABLE IMMERSION & SUCTION COOLANT OIL PUMPS   1/4 HP Totally Enclosed Motor (TEFC) Three Phase Motor 230/460 volts  0.8/0.4 amps Stainless Steel or Composite Semi-open Impeller Options Immersion and Suction Types Cast Iron Construction Handles Viscosity up to 500 SSU Standard Replacement for Machine Tool Industry Delivers up to 56 GPM and 26 PSI 3/4" FNPTOutlet   AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants. AMT Interchangeable Coolant/Oil pumps are reliable, cost effective and low maintenance. For use with non-flammable liquids compatible with pump component materials.  

AMT 5391-95, Immersion Coolant Oil Pump 23gpm 230/460volt INTERCHANGEABLE IMMERSION & SUCTION COOLANT/OIL PUMPS   Cast Iron Construction 1/4 HP 230/460V 3 Phase Immersion Type Shaft Seal Material: Sealless Design Speed (RPM): 3450 Type: IMM Voltage: 230/460 Fluid Port: 0.5" HP:1/4 Impeller Material: Stainless Steel GPM: 23   Replacement for Standard Machine Tool Industry Pumps  Fuji: VKP-063A Old Fuji: VKN-061A Mitsubishi: NQ100J  Toshiba: OPF-100M Hitachi: CPD-100M Yasukawa: VFPC-100 Graymills: IMV-25   AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants. AMT Interchangeable Coolant/Oil pumps are reliable, cost effective and low maintenance. For use with non-flammable liquids compatible with pump component materials.  

AMT 285P-95, Self-Priming Centrifugal Pump 3/4 HP, 3 PH, 230/460 V Cast Iron Construction Buna-N Mechanical Seal and O-Ring with optional Viton? or Silicon Carbide Mechanical Seal and O-ring 1" & 1-1/4" NPT Suction and Discharge Ports Dual Volute Design Reduces Radial Load on Motor Maximum Working Pressure 75 PSI Maximum Temperature 180 F Self-cleaning, Semi-open Impeller

AMT Pump 4822-95 Rotary Hand Pump AMT Rotary Drum Pump 1" Suction & 3/4" Discharge Buna-N Shaft Seal Includes: Bung Adapter & Suction Tube Included Material: Cast Iron

AMT Pump 5272-98 SS Rotary Drum Pump Drum Pump, Stainless Steel, 1" NPT Suction x 3/4" NPT Discharge Port Rotary drum pump for transfer of chemicals and liquids including many acids, acetones, trichloroethylene, solvents, photographic chemicals and ketones. Hand-operated rotary lever action 304 stainless steel construction with carbon vanes and a Teflon (PTFE) seal for resistance to chemicals and corrosion Flow rate of 12 oz. per stroke (5 gpm at 70 rpm) 1" female NPT inlet port and 3/4" female NPT outlet port