|
Flotec FP5512 Cast Iron Centrifugal Pump 1/2 HP
Economical, general purpose centrifugal pumps can be used for water transfer, circulation, fountains, waterfalls, pressure boosting and sprinkling.
FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install 230 volt motor (dual voltage)
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 22 GPM
MAX LIFT: 25'
MAXIMUM DISCHARGE PRESSURE: 36 psi
MAXIMUM INLET PRESSURE:
MAXIMUM TOTAL PRESSURE:
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 4.7 amps on 230v / 9.4 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
RECOMMENDED BREAKER: 15 amp on 230v / 15 amp on 115v
|
440.70 |
|
|
Flotec FPSE3601A Cast Iron Sewage Pump 1/2 HP
Rugged, sewage and effluent pumps are capable of handling solids up to 2". Available in cast iron design for a variety of wastewater applications.
Heavy-duty, rugged cast iron automatic submersible sewage pump
Capable of handling 2" solids - ideal for basement installations, pumping below grade toilets, laundry facilities, underground parking, grain storage and construction sites
Includes by-pass float switch for automatic or manual operation
BODY CONSTRUCTION: CAST IRON
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9000 GPH
FLOW AT 10' LIFT: 5400 GPH
SWITCH TYPE: Tethered
DISCHARGE PIPE SIZE: 2" NPT
MINIMUM PIPE SIZE: 2" for sewage applications / 1-1/2" for effluent applications
MAXIMUM SOLID HANDLING SIZE: 2"
CORD LENGTH: 10'
AMP DRAW: 13 amps
VOLTAGE: 115v. 60 Hz
RECOMMENDED BREAKER: 20 amp
|
699.00 |
|
|
Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9 GPM (shallow well setup)
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM (shallow well setup)
MAX LIFT: 25' w/ shallow well jet kit / 70' w/ deep well jet kit
MAX PSI: 62 psi (shallow well setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4"
MINIMUM SUCTION PIPE SIZE: 1-1/4"
DRIVE PIPE SIZE: 1"
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
516.00 |
|
|
Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP
This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less.
KEY FEATURES
Perfect for shallow wells (depth-to-water less than 25')
Thermoplastic construction for higher corrosion resistance
1-1/4" Suction / 1" Discharge
Comes with pre-wired 30/50 pressure switch
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8 GPM
FLOW at 10' LIFT and 40 PSI: 6.4 GPM
MAX LIFT: 25'
MAX PRESSURE: 77 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 9.4 amps
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
432.90 |
|
|
Flotec FP5532 Cast Iron Centrifugal Pump 1 HP
Economical, general purpose centrifugal pumps can be used for water transfer, circulation, fountains, waterfalls, pressure boosting and sprinkling.
FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Maximum pumping capacities to 68 GPM
Ready-to-install 230 volt motor (dual voltage)
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1
MAXIMUM CAPACITY: 47 GPM
MAXIMUM LIFT: 25'
MAXIMUM DISCHARGE PRESSURE: 49 psi
MAXIMUM INLET PRESSURE:
MAXIMUM TOTAL PRESSURE:
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
LIQUID TEMP RANGE: 140 °F (60 °C)
|
531.75 |
|
|
Flotec FP5230 Cast Iron Sprinkler Pump 1 HP
Powerful 1 HP cast iron sprinkler pump moves up to 45 gpm. Perfect for sprinkler systems or water transfer applications.
FEATURES
Superior performance at depths-to-water of 25' or less Ideal for larger sprinkler systems and water transfer
Rugged cast iron construction Voltage-selectable to run on 115v or 230v
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1
MAXIMUM CAPACITY: 45 GPM
FLOW at 10' LIFT and 30 PSI: 35 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 50 psi
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 8.8 amps on 230v / 16.6 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 25 amp on 115v
MAXIMUM WATER TEMPERATEURE: 140 F (60 C)
|
761.04 |
|
|
Flotec FPZS50T Submersible Thermoplastic Sump Pump
Flotec's 1/2 HP sump pump with energy-efficient design that produces high-output performance. Constructed from engineered composites providing dependable, corrosion-resistant service for years to come. Tethered on/off float switch.
Thermoplastic construction - resists corrosion
Zinc motor housing - dissipates heat quickly and extends motor life
Stainless steel fasteners and hardware - for long life
Smooth Flow Hydraulics - delivers high performance for demanding applications
Switch Type: Tethered - Operates in 14" basins or larger
Horse Power: 1/2 HP
GPH: 4,200
Max Lift: 22'
Solids Handling: 3/16"
Discharge: 1/5" NPT
Power Cord: 8', Grounded
|
286.26 |
|
|
Flotec FPZS50V Submersible Thermoplastic Sump Pump 1/2 HP
Flotec's 1/2 HP sump pump with energy-efficient design that produces high-output performance. Constructed from engineered composites providing dependable, corrosion-resistant service for years to come. Vertical on/off float switch can be used in smaller sump basins.
FEATURES
Thermoplastic construction - resists corrosion
Zinc motor housing - dissipates heat quickly and extends motor life
Stainless steel fasteners and hardware - for long life
Smooth Flow Hydraulics - delivers high performance for demanding applications
1 Year Limited Warranty
Switch Type: Vertical - Operates in 10" basins or larger
Horse Power: 1/2 HP
GPH: 4,200
Max Lift: 22'
Solids Handling: 3/16"
Discharge: 1.5" NPT
Power Cord: 8', Grounded
|
296.40 |
|
|
Flotec FP5172 Thermoplastic Sprinkler Pump 1.5 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1-1/2
MAXIMUM CAPACITY: 67 GPM
FLOW at 10' LIFT and 30 PSI: 45 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 47 psi
SUCTION PIPE SIZE: 1-1/2" NPT
DISCHARGE PIPE SIZE: 1-1/2" NPT
AMP DRAW (full load): 9.6 amps on 230v / 19.2 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 25 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
621.00 |
|
|
Flotec FPSE2800A Thermoplastic Effluent Pump
The FPSE2800A provides the answer to many effluent/dewatering situations where 3/4" solids handling is all that is needed.
Automatic submersible effluent/dewatering pump
Capable of handling 3/4" solids - ideal for basement installations, laundry facilities, underground parking, grain storage and construction sites
Thermoplastic construction
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/3
MAXIMUM CAPACITY: 3600 GPH
FLOW AT 10' LIFT: 2700 GPH
SWITCH TYPE: Tethered
SWITCH ON LEVEL: 11-1/2"
SWITCH OFF LEVEL: 4-1/2"
DISCHARGE PIPE SIZE: 2"
MINIMUM PIPE SIZE: 1-1/2"
MAXIMUM SOLID HANDLING SIZE: 3/4"
CORD LENGTH: 15'
AMP DRAW: 7 amps
VOLTAGE: 115v, 60 Hz
|
436.80 |
|
|
Flotec N76-46P Pump Body
This is the durable plastic pump body, that is specially designed for use with Flotec shallow well jet pumps.
Replacement pump body N76-46P covers the pump impeller and directs water flow through the pump. This part replaces a worn or damaged body to restore proper pumping.
The Flotec, Simer and Sta-Rite pumps have interchangeable parts. If the part number is the same, it will work in any of the Flotec, Simer and Sta-Rite pumps.
|
122.85 |
|
|
Flotec FP4122 Well Pump 3/4Hp 115/230V
Flotec Shallow Well Jet Pump, Cast Iron Construction, 3/4HP 115/230V, 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 14.4GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth
|
720.00 |
|
|
Flotec FP4822 Stainless Steel Shallow Well Jet Pump 3/4 HP
Stainless steel shallow well jet pumps are heavy-duty, durable, corrosion resistant, high pressure and offer efficient non-stop operation for years.
KEY FEATURES
Superior performance at depths to water of 25' or less
Heavy-duty, stainless steel pump housing for highest corrosion resistance
Ready-to-install 230 volt motor - see manual for 115 volt conversion
1-1/4" NPT suction and 1" NPT discharge pipe sizes
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Stainless Steel
HORSEPOWER: 3/4
MAXIMUM CAPACITY: 11 GPM
FLOW at 10' LIFT and 40 PSI: 11 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 52 psi
MAXIMUM INLET PRESSURE:
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: NPT
AMP DRAW (full load): 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 20 amp on 115v
MAXIMUM WATER TEMPERATURE: 122°F (50 °C)
|
734.40 |
|
|
Flotec FP4332 Thermoplastic Convertible Jet Pump 1 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor - see manual for 115 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1
MAXIMUM CAPACITY: 20.7 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 18.3 GPM (shallow setup)
MAX LIFT: 25' for shallow setup / 90' for deep setup
MAXIMUM PRESSURE: 52 psi for shallow / 56 psi for deep
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW: 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 20 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
698.25 |
|
|
Flotec FPSC1725X-03 Cast Aluminum Water Removal Utility Pump 1/4 HP 1250 GPH
Cast Aluminum construction provides years of service for those emergency water removal situations.
FEATURES
Heavy-duty, epoxy coated, cast aluminum construction
Portable pump for emergency water removal or emptying shallow flooded areas
Draws water down to 1/8"
Switch for automatic operation sold separately
3-year limited warranty
BODY CONSTRUCTION: Cast Aluminum
HORSEPOWER: 1/4 HP
MAXIMUM CAPACITY: 1320 GPH
FLOW AT 10' LIFT: 1020 GPH
DISCHARGE SIZE: 1¼" (male) NPT
VOLTAGE: 115v AC, 60 Hz
CORD LENGTH: 8' with 3-prong grounded plug
MAXIMUM WATER TEMPERATURE: 120°F (50°C)
|
191.10 |
|