|
Leveler Short Hose Trim - 2-1/2" with Screws
Hose trim is used for appearance and to conceal the hole that is drilled for the hydraulic hose to pass through the transom.
Features:
2-1/2 inches
Resist ultraviolet rays and are made of impact-resistant nylon or glass-filled, thus eliminating expansion from hydraulic pressure and water absorption
Hose trim comes with four black xylon-coated screws
|
13.50 |
|
|
Long Hose Trim - 3-1/2" with Screws
Hose trim is used for appearance and to conceal the hole that is drilled for the hydraulic hose to pass through the transom.
Features:
3-1/2 inches
Resist ultraviolet rays and are made of impact-resistant nylon or glass-filled, thus eliminating expansion from hydraulic pressure and water absorption
Hose trim comes with four black xylon-coated screws
|
13.50 |
|
|
Ampco Pumps KC2 2 1/2 X 2 Fluid End Nialbz 5.00" Trim
|
3440.34 |
|
|
Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 400lb working pressure. Entering the transom 6" above the water line, the hoses are held securely with hose trim. Stainless steel clamps hold the hose to barb fitting at the solenoid.
|
5.40 |
|
|
Jabsco 1210-0001-B Neoprene Impeller
Rubber Type: Neoprene
Outer Diameter: 2-1/4 Inches / 57 mm
Depth: 1-1/4 Inches / 31.5 mm
Shaft Size: 5/8 Inches / 16 mm
Drive Type: 12 Point Spline
Drive Core Type: Brass
Number of Blades: 12
Typical Liquid Use: Water, Glycol, Engine Cooling, Beer, Wine, Whiskey, Cider
This Neoprene Impeller replaces the following
Detroit Diesel 5194205
Volvo 825940 860203 875811
Onan 132-0162
Perkins 0460038
Gray 74306
Northern Lights 25-12060
|
32.89 |
|
|
Insta-Trim Boat Leveler 12 Volt Solenoid Valve with White Wire. They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
|
94.50 |
|
|
Insta-Trim Boat Leveler 12 Volt Solenoid Valve with Green Wire. They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
|
94.50 |
|
|
Insta-Trim 10" x 10" Trim Tab Set
Insta-Trim, the original hydraulic boat leveler, provides a better ride every time you leave the dock. Each Insta-Trim system features:
Wiring: Color-coded wiring in 25' and 40' lengths with quick connect fittings, meets federal standards for heat, pull and insulation.
Solenoids: Our solenoids are custom designed for Insta-Trim Boat Leveler company, epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb type hose fittings provide tight, secure connections.
Motor: A powerhouse with coated wiring that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminates oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Pump: Designed and engineered exclusively by Insta-Trim. The built-in bypass is factory set at 400 P.S.I. Tolerance held to +/-.00025. Amperage doesn?t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Brackets: Swivel type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins if the tab strikes an object.
Cylinders: Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus 0-rings, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular steel rod prevents hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion.
Stainless Steel Trim Tabs: 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim systems use hinges that prevent most spray and can be used for transom or bottom mounting.
Motor cover: High impact abs plastic cover with a built-in oil reservoir mounts easily with two screws. Our cover protects the motor from occasional wash down.
Hose: Designed and manufactured exclusively for Insta-Trim with nylon reinforced webbing and a UV resistant coating. Rated at 2000 lbs. Burst pressure, 15; of hose is supplied for your system. Stainless steel clamps hold the hose to barb fittings at the solenoids and at the cylinder connection.
Rocker type controls: Mounted on the dash, they are easy to operate.
Optional touch button waterproof switches: Adjust the tabs for maximum control and performance. 3" Diameter.
|
576.13 |
|
|
Insta-Trim 12" x 12" Trim Tab Set
Insta-Trim, the original hydraulic boat leveler, provides a better ride every time you leave the dock. Each Insta-Trim system features:
Wiring: Color-coded wiring in 25' and 40' lengths with quick connect fittings, meets federal standards for heat, pull and insulation.
Solenoids: Our solenoids are custom designed for Insta-Trim Boat Leveler company, epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb type hose fittings provide tight, secure connections.
Motor: A powerhouse with coated wiring that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminates oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Pump: Designed and engineered exclusively by Insta-Trim. The built-in bypass is factory set at 400 P.S.I. Tolerance held to +/-.00025. Amperage doesn?t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Brackets: Swivel type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins if the tab strikes an object.
Cylinders: Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus 0-rings, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular steel rod prevents hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion.
Stainless Steel Trim Tabs: 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim systems use hinges that prevent most spray and can be used for transom or bottom mounting.
Motor cover: High impact abs plastic cover with a built-in oil reservoir mounts easily with two screws. Our cover protects the motor from occasional wash down.
Hose: Designed and manufactured exclusively for Insta-Trim with nylon reinforced webbing and a UV resistant coating. Rated at 2000 lbs. Burst pressure, 15; of hose is supplied for your system. Stainless steel clamps hold the hose to barb fittings at the solenoids and at the cylinder connection.
Rocker type controls: Mounted on the dash, they are easy to operate.
Optional touch button waterproof switches: Adjust the tabs for maximum control and performance. 3" Diameter.
|
579.54 |
|
|
Insta-Trim 18" x 11" Trim Tab Set
Insta-Trim, the original hydraulic boat leveler, provides a better ride every time you leave the dock. Each Insta-Trim system features:
Wiring: Color-coded wiring in 25' and 40' lengths with quick connect fittings, meets federal standards for heat, pull and insulation.
Solenoids: Our solenoids are custom designed for Insta-Trim Boat Leveler company, epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb type hose fittings provide tight, secure connections.
Motor: A powerhouse with coated wiring that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminates oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Pump: Designed and engineered exclusively by Insta-Trim. The built-in bypass is factory set at 400 P.S.I. Tolerance held to +/-.00025. Amperage doesn?t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Brackets: Swivel type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins if the tab strikes an object.
Cylinders: Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus 0-rings, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular steel rod prevents hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion.
Stainless Steel Trim Tabs: 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim systems use hinges that prevent most spray and can be used for transom or bottom mounting.
Motor cover: High impact abs plastic cover with a built-in oil reservoir mounts easily with two screws. Our cover protects the motor from occasional wash down.
Hose: Designed and manufactured exclusively for Insta-Trim with nylon reinforced webbing and a UV resistant coating. Rated at 2000 lbs. Burst pressure, 15; of hose is supplied for your system. Stainless steel clamps hold the hose to barb fittings at the solenoids and at the cylinder connection.
Rocker type controls: Mounted on the dash, they are easy to operate.
Optional touch button waterproof switches: Adjust the tabs for maximum control and performance. 3" Diameter.
|
636.82 |
|
|
Insta-Trim boat leveler's electronic tab locator shows the
position of your tabs. Two seperate lines of diode lamps
accurately indicate the position of each tab. the screen is
small, mounts on the dashboard, and is designed to
match your rocker type controls in size and appearance.
The detectors are rugged and attach easily and quickly to
each hydraulic cylinder. The attached readout line runs
up to the light panel with simple plug in connections.
Insta-Trim electonic tab locators can be added to your
existing boat leveler system, upgrading your system for a
better, more accurate performance.
Installation is quick, easy, and simple. Only a few
common tools are rquired, and the tab locators come
with easy to follow instructions.
|
364.50 |
|
|
Insta-Trim boat leveler's electronic tab locator shows the
position of your tabs. Two seperate lines of diode lamps
accurately indicate the position of each tab. the screen is
small, mounts on the dashboard, and is designed to
match your rocker type controls in size and appearance.
The detectors are rugged and attach easily and quickly to
each hydraulic cylinder. The attached readout line runs
up to the light panel with simple plug in connections.
Insta-Trim electonic tab locators can be added to your
existing boat leveler system, upgrading your system for a
better, more accurate performance.
Installation is quick, easy, and simple. Only a few
common tools are rquired, and the tab locators come
with easy to follow instructions.
|
364.50 |
|
|
Stainless Steel Short Side Door Hinge - Stamped #8 Screws Individual Bulk Packaging
These Short Side Door Hinges are great for interior and exterior applications such as cabinets, hatches, folding tables, or seats where mounting space is tight. Constructed of corrosion resistant stamped 304 stainless steel. Installs with five #8 FH fasteners (not included).
|
5.56 |
|
|
Air Boat - 12" x 9" Trim Tab Kit
Single center-mounted tab set specifically designed for air boats.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
559.73 |
|
|
Mercruiser Tilt Trim Reservoir Kit - 4 Screw Mount
Tilt trim reservoir kit that will fit Arco 6275 Tilt Motor 4 screw mount. Replaces Mercruiser.
Replaces:
Mercruiser 883166A2
*ARCO Assurance 12-month part and labor warranty protection
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
43.04 |
|