Backing Plate for 70 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series. Features: Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Backing Plate for 80 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series. Features: Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA) 316L cast stainless steel 4-1/4" x 6" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Replacement Liner for 70 Series - White Replacement liner for 70 series in-gunnel and clamp-on rod holders. This UV-resistant vinyl liner protects rods. Features: Recessed liner (doesn't come to the top of the tube) Made of white vinyl material

Sidewinder Backing Plate f/Bolt-In Holders Below top operation. Fully locked in Running and 80° out Trolling positions. Locks when handle is up or down. Rotates when handle is to the left or right. Fastest Lay-Down on the market. Automatically locks in position when raising or lowering the pole. No knobs to loosen or tighten. Just pull down the Ridged Collar and lower or raise the pole. Available with Quick Laydown or Curved Tube. No ball bearings to rust. Internal Delrin and nylon bearing surfaces provide smooth operation and prevent metal to metal contact. Accepts our 16Ft Extra Strong (AP3916XS) or 18Ft (AP3918) Outrigger Pole. Has 4"x6" Mounting plate. Extends 14" above and 8-1/2" below mounting plate. Fits all outrigger ready boats.

Single Aluminum 5° Transom Mount Rod Holder The perfect way to add rod holders to the transom area. Designed with outboard engine wells in mind. An ideal way to add rod holders to a seating station. These rod holders feature a super strong 3/8" thick blade, rugged welded 1/3" tallgimbal bar, and a 1-5/8" inside diameter with a flared opening to make it easy to insert a rod in the holder. The taper liner and the addition of a rod security hole in the blade ensures that your valuable rods are protected. Mount vertically or with some outward angle for a wider fishing spread. Tube leans 5° away from the 3" tall x 2-3/4" wide mounting base. 10" overall height. Includes white vinyl liner.

Gunnel Mount Backing Plates f/88502 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Side Mount Backing Plates f/88505 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Large Gunnel Mount Backing Plates f/88506 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Large Side Mount Backing Plates f/88508 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Replacement liner for 80 series in-gunnel rod holder, 11" long, cut to desired angle and length. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Heavy Duty Pro Series Rod Holders The Pro Series line of molded rod holders takes the Pro Series to the next level with the addition of the Combo Mount. All the Pro-Series unique features you've come to expect, with the ability to mount in multiple configurations. Designed for use with casting and spinning rod holders. Heavy-duty, deep-tooth gear lock securely holds rod holder in mounting base. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

700A Series Rod Holder This rod holder is constructed of anodized aluminum and stainless steel for use in all freshwater and saltwater environments. More specifically, this rod holder is suitable for most walleye and panfish rods. An excellent choice for light trolling or still fishing. Features: Panther Rod Holders are designed and manufactured by CMP Group, the world’s leading producer of state-of-the-art boating and fishing equipment Posi-LOCK technology – 25 and 45-degree angles For optimum fishing performance, Panther gives you a full 360-degree hemisphere of possible positions The mounting base on all Panther models can be easily removed from the unit with an Allen Wrench for storage Panther Rod Holders are precision-made out of rust-resistant stainless steel and aluminum for freshwater and saltwater fishing 7 3/4 in. depth fits most standard rod sizes Mounting hardware is included Specifications: Base Plate (inch): 2-3/4" Tube Diameter (inch): 1-3/4" Tube Depth (inch): 7-3/4"

441 Backing Plate f/241 & 244 Mount Use the Scotty Backing Plate to add structural support when attaching the Scotty 241L / 241 Combination Side / Deck Mount or the Scotty 244L / 244 Flush Deck Mount to thin-walled watercraft. Made with super tough, rugged engineering grade nylon. *Stainless steel nuts & machine screws included. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

800A Series Rod Holder This rod holder is constructed of anodized aluminum and stainless steel for use in all freshwater and saltwater environments. This is Panther's most popular rod holder. It will accept most heavy-duty trolling rods and is the choice of serious anglers and charter captains throughout the Great Lakes as well as the Pacific Northwest. Features: Panther Rod Holders are designed and manufactured by CMP Group, the world’s leading producer of state-of-the-art boating and fishing equipment Posi-LOCK technology – 25 and 45-degree angles For optimum fishing performance, Panther gives you a full 360-degree hemisphere of possible positions The mounting base on all Panther models can be easily removed from the unit with an Allen Wrench for storage Panther Rod Holders are precision-made out of rust-resistant stainless steel and aluminum for freshwater and saltwater fishing 10 in. depth for larger fishing rods Mounting hardware is included Specifications: Base Plate (inch): 2-3/4" Tube Diameter (inch): 1-3/4" Tube Depth (inch): 10"

Plastic Rod & Cup Holder Backing Plate for Round Rod/Cup Only for 3-3/4" Holes Threaded Backing Plates for replacing existing ø3-3/4 cup holders with ROUND ABS PLASTIC Combination Rod & Cup Holders. Screws are included. For use with Round Top ABS Plastic Only in a ø3-3/4 existing hole.