Permanent Waterheater Bypass Kit Save on antifreeze when you winterize with this easily-installed water heater by-pass kit. Sturdy, brass backflow preventer and 100% shut-off valve lets you by-pass the water heater with a single turn.

Quick Flush™ Outboard Flush Fitting Kit for Mercury & Yamaha Outboards Provides a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating water pressure keeps the valve sealed when using engine.  Features: Makes flushing outboard quick and easy Unique previously patented slide valve replaces outboard flushing port plug O-ring seal closes off port when operating engine Quick connect on hose snaps onto valve for flushing No plug to remove and no difficult turning of hose into port Takes the hassle out of flushing your outboard Fits all outboards equipped with a flushing port Kit consists of slide valve, hose quick connector, and washer WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flojet 20378-000 Bypass Kit 30-45 Psi

Flojet 20378-001 Bypass Kit 45-55Psi  

Flojet 20378-003 Bypass Kit 60-80 Psi  

Flojet 20378-012 Bypass Kit 50Psi  

Quick Zinc Propeller Nut Anode Kit for BTQ140 Bow Thrusters Tecnoseal Quick Zinc Propeller Nut Anode Kit BTQ140 for 140mm diameter tunnel. For use in salt water. Mounting screw is not included. Most thrusters require 2 anodes.

Quick Zinc Propeller Nut Anode Kit for BTQ110-125 Bow Thrusters Tecnoseal Quick Zinc Propeller Nut Anode Kit BTQ110 for 110mm diameter tunnel. For use in salt water. Mounting screw is not included. Most thrusters require 2 anodes.

Quick Zinc Propeller Nut Anode Kit for BTQ185 Bow Thrusters Tecnoseal Quick Zinc Propeller Nut Anode Kit BTQ185 for 185mm diameter tunnel. For use in salt water. Mounting screw is not included. Most thrusters require 2 anodes.

Quick Zinc Propeller Nut Anode Kit for BTQ250 Bow Thrusters Tecnoseal Quick Zinc Propeller Nut Anode Kit BTQ250 for 250mm diameter tunnel. For use in salt water. Mounting screw is not included. Most thrusters require 2 anodes.

Quick Zinc Propeller Nut Anode Kit for BTQ300 Bow Thrusters Tecnoseal Quick Zinc Propeller Nut Anode Kit BTQ300 for 300mm diameter tunnel. For use in salt water. Mounting screw is not included. Most thrusters require 2 anodes.

20' Coiled Hose & Spray Nozzle Kit Camco’s 20-Foot Coiled Hose and Spray Nozzle Kit is a complete wash kit that is ideal for marine use, as well as general cleaning, car washing and daily gardening since they are lightweight, easy-to-use and store. The coiled hose features strain relief to help prevent kinking. Included in the kit are an adjustable spray tip nozzle with thumb lever for flow control as well as a quick connect fitting. The quick connect fitting allows the hose to easily attach/detach from the spray tip nozzle as well as allow the nozzle to swivel a full 360-degrees. Features: Complete 20-foot coiled hose assembly that is ideal for marine use, as well as general cleaning, car washing and daily gardening Kit includes: 20-foot coiled hose, nozzle with thumb lever, a spray pattern adjustment dial, swiveling/quick connect fitting and vented storage bag with a carry handle and D-ring Coiled hose features strain relief to help prevent kinking and self-coils for easy storage Quick connect fitting allows the hose to easily attach/detach from the spray tip nozzle and swivel 360-degrees Nozzle has thumb lever flow control and an easily adjustable spray

40' Coiled Hose & Spray Nozzle Kit Camco’s 40-Foot Coiled Hose and Spray Nozzle Kit is a complete wash kit that is ideal for marine use, as well as general cleaning, car washing and daily gardening since they are lightweight, easy-to-use and store. The coiled hose features strain relief to help prevent kinking. Included in the kit are an adjustable spray tip nozzle with thumb lever for flow control as well as a quick connect fitting. The quick connect fitting allows the hose to easily attach/detach from the spray tip nozzle as well as allow the nozzle to swivel a full 360-degrees. Features: Complete 40-foot coiled hose assembly that is ideal for marine use, as well as general cleaning, car washing and daily gardening Kit includes: 40-foot coiled hose, nozzle with thumb lever, a spray pattern adjustment dial, swiveling/quick connect fitting and vented storage bag with a carry handle and D-ring Coiled hose features strain relief to help prevent kinking and self-coils for easy storage Quick connect fitting allows the hose to easily attach/detach from the spray tip nozzle and swivel 360-degrees Nozzle has thumb lever flow control and an easily adjustable spray

Marine Holding Tank Vent Filter Kit Camco's Marine Holding Tank Vent Filter Kit helps eliminate odors that are released from your boat's holding tank vent. It features granular activated carbon (GAC) for maximum odor control. This allows odorous gases to be properly filtered, helping absorb any holding tank smells. Kit installs easily to your boat's vent hose. The product includes a filter, mounting bracket, and fittings for standard garden hose connections, 3/4-inch, and 5/8-inch barbed hose connections. The mounting bracket measures 12-1/8-inches (L) x 2-3/4-inches (D) x 2-3/4-inches. The filter will last an entire boating season or more, depending on the usage. Features: Helps Eliminate Odors: Kit helps eliminate odors that are released from your boat's holding tank vent Provides Maximum Odor Control: Filter contains granular activated carbon (GAC) for maximum odor control Includes: A filter, mounting bracket, and fittings for standard garden hose connections, 3/4-inch, and 5/8-inch barbed hose connections Easy to Install: Installs easily to your boat's vent hose Dimensions: Mounting bracket measures 12-1/8-inches (L) x 2-3/4-inches (D) x 2-3/4-inches Note: The filter will last an entire boating season or more, depending on the usage

PED4400-C PedestalPod Uncut (Usable Face = 8.75"W x 6"H) (22.2cm W x 15.2cm H) - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.