Compact battery monitor, just 124 x 62mm x 23mm! Based on the highly successful BM-1 marine battery monitor, the BM-1 Compact is especially designed for applications where space is at a premium. Caravans, mobile homes, RV's, small boats and renewable power installations can all benefit from the BM-1 Compact. It is able to monitor the performance of any 12 Volt lead acid battery system with a capacity up to 600 AmpHours. The BM-1 Compact is supplied with a precision 100 Amp shunt and prefabricated cables to enable simple DIY installation. The unit continually monitors the voltage, the current (charge or discharge) and calculates the state of charge together with the time remaining to charge or discharge the battery. This information can lead to a more efficient use of the battery enhancing its life and reducing the risk of failure. Operation is very simple. One screen displays the voltage, current (charge or discharge) and a bar graph showing the remaining capacity. A flashing alarm is also included to warn if the capacity is getting too low. A second screen shows the remaining time available at the current charge/discharge rate together with the remaining capacity in both analog and digital format. The BM1 Compact consumes a miserly 1.5mA!This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Clipper BM-2 Battery Monitor The BM-2 is designed to monitor performance of 12 volt lead acid battery systems with capacities of up to 600 Amp hours. It is supplied complete with a precision 200 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure. Specifications: Supply voltage: 8-16 volts DC Supply current: 1.5 milliamps Battery capacities: 5-600 AMP Hour Load Current: 199 Amps Max Charge Current: 199 Amps Max Shunt: Standard 50 millivolt @ 200 Amp Cables Supplied: 200 Amp shunt link to M8 Ring terminal. 5 meter from display unit to battery - fused and fitted with ring terminals for shunt, fuse holder, and M8 ring terminal to battery. Display Unit: Standard 110m squre clipper case. High contrast LCD, backlit for night viewing. Minimum voltage visual alarm Simple operation: 4 keys to select backlight, Volt/Amp/State of charge screen, AMP hours or time to run. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Compact battery monitor, just 124 x 62mm x 23mm! Based on the highly successful BM-1 marine battery monitor, the BM-1 Compact is especially designed for applications where space is at a premium. Caravans, mobile homes, RV's, small boats and renewable power installations can all benefit from the BM-1 Compact. It is able to monitor the performance of any 12 Volt lead acid battery system with a capacity up to 600 AmpHours. The BM-1 Compact is supplied with a precision 100 Amp shunt and prefabricated cables to enable simple DIY installation. The unit continually monitors the voltage, the current (charge or discharge) and calculates the state of charge together with the time remaining to charge or discharge the battery. This information can lead to a more efficient use of the battery enhancing its life and reducing the risk of failure. Operation is very simple. One screen displays the voltage, current (charge or discharge) and a bar graph showing the remaining capacity. A flashing alarm is also included to warn if the capacity is getting too low. A second screen shows the remaining time available at the current charge/discharge rate together with the remaining capacity in both analog and digital format. The BM1 Compact consumes a miserly 1.5mA! This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

BM-1 LI Battery Monitor for 12V Lithium The BM-1 battery monitor is designed to monitor performance of 12 volt lead acid battery systems, including AGM and GEL types with capacities of up to 600 Amp hours. It is supplied complete with a precision 100 AMP shunt and a prefabricated cable assembly to enable simple DIY installation. The unit continuously monitors voltage, current (charge or discharge), number of amp/hours (charge or discharge), the batteries state of charge and the time to charge or discharge. It also monitors the voltage of the engine strat battery. This information leads to more efficient use of the battery, which can enhance battery life and reduce the risk of failure. Features: Fully monitors domestic battery/bank Monitors voltage of engine start battery Specifications: Supply Voltage BM-1  12V 8 – 16 Volts DC BM-1  24V 16 – 32 Volts DC Supply current 1.5 milliamps Battery capacities 5 – 600 AMP Hour Load current 100 AMPS Maximum Charge current 100 AMPS Maximum Shunt Standard 50 millivolt @ 100 AMP Cables Supplied: 100 AMP shunt link to M8 Ring terminal. 5 Metre from display unit to battery – fused and fitted with ring terminals for shunt, fuse holder and M8 ring terminal to battery. Display unit Standard 110mm square Clipper case. High contrast LCD, backlit for night viewing. Minimum voltage visual alarm Simple operation – 4 keys to select backlight, Volt/Amp/State of Charge screen, AMP hours or Time to run. How Does It Work? A simple and intuitive display shows the service battery voltage, charge/discharge current, state of charge, and time to charge/discharge. The instrument also warns the user when the charge level is too low so that load can be shed or charging commenced to protect the battery. A resettable Amp Hour counter is provided for checking the efficiency of the charging system or keeping a track of power consumption and a second input lets the user monitor the voltage of the starter battery. The simple display format does not mean the internal software is unsophisticated. In fact two separate algorithms are used. One based on integrating amp hours over the charge and discharge cycle, the second based on an adaptive internal mathematical battery model. A unique feature of the BM1+ is its ability to use information from both algorithms, during the charge/discharge cycles, to continually update its performance. This means that, unlike many other systems that rely solely on amp hour integration, the NASA BM1+ never needs to be re-synchronised with the battery. The algorithm includes Peukert's equation to ensure accuracy over a wide range of load currents. The BM1+ does all this whist consuming a meagre one and a half milliamps. It is a true battery monitor, easy to install and excellent value for money. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Bluetooth Battery Monitor When you need a battery monitor but don't have space for the display or routing thecables would be a nightmare, there is now a solution. The BM-1(BT) will monitor yourboat or caravan's lead-acid batteries and transmit the data directly to your mobile phone,or tablet, wirelessly by bluetooth. A simple Android app, freely available from the nasamarine.com website or Google PlayStore, (requires Android V4.3 or later) shows your service battery voltage, current flowingin or out, state of charge and time to charge or discharge the battery. An audible alarmwarns if the battery level gets dangerously low. It will also show the starter batteryvoltage. For apple users a more sophisticated app, with additional features can bepurchased from the Apple app store. Compatible with iPhone, iPad and iPod touch.Offers Apple Watch App for iPhone. (Requires iOS 9.0 or later) The monitor, which draws a meagre 2 mA, is supplied with a 100 amp shunt and a premadecable assembly to simplify connection to your service battery.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Smart Battery Monitor - BMV-712 - Grey - Bluetooth Capable Features: Bluetooth inside With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.  Download the Victron Bluetooth app Use a smartphone or other Bluetooth enabled device to - customize settings, - monitor all important data on single screen, - view historical data, and to - update the software when new features become available.  Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting.  Midpoint voltage monitoring One bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information. We recommend our Battery Balancer (BMS012201000) to maximize service life of series-connected lead-acid batteries.  Very low current draw from the battery Current consumption: 0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24V Especially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown. After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA for example may damage a 200Ah battery if the system is left in discharged state during more than 8 days.  Bi-stable alarm relay Prevents increased current draw in case of an alarm.  Other features - Battery voltage, current, power, ampere-hours consumed and state of charge - Remaining time at the current rate of discharge - Programmable visual and audible alarm - Programmable relay, to turn off non critical loads or to run a generator when needed - 500 Amp quick connect shunt and connection kit - Shunt selection capability up to 10.000 Amps - VE.Direct communication port - Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health - Wide input voltage range: 6,5 – 70V - High current measurement resolution: 10 mA (0,01A) Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.

Lynx Smart BMS 1000 Battery Management System for Lithium Smart Batteries The Lynx Smart BMS is a dedicated Battery Management System (BMS) for the Victron Lithium Battery Smart batteries. These batteries are Lithium Iron Phosphate (LiFePO4) batteries and are available in 12.8 V or 25.6 V in various capacities. They can be connected in series, parallel, and series/parallel so that a battery bank can be built for system voltages of 12V, 24 V, or 48 V. The maximum number of batteries in one system is 20, which results in a maximum energy storage of 84 kWh in a 12 V and up to 102 kWh in a 24 V1) and 48 V1) system. Out of the various available BMSes, the Lynx Smart BMS is the most feature-rich and complete option and integrates seamlessly into the Lynx Distributor system. This model is a 1000 A (M10) version. Built-in 1000 A Contactor The contactor acts as a secondary safety system to protect the battery in case the primary controls (ATC, ATD, and/or DVCC) fail to disable loads and/or chargers when required and is also suitable as a remote controllable main system switch. Pre-charge Circuit In addition to the contactor, a built-in pre-charge circuit prevents high inrush currents when connecting a capacitive load such as a MultiPlus/Quattro or other inverter, eliminating the need for external pre-charging. Monitoring and Control Monitor and control the BMS via Bluetooth using the VictronConnect App or a GX device such as a Cerbo GX and the VRM Portal. A built-in battery monitor that operates similarly as the other Victron Energy battery monitors, provides data such as state of charge, voltage, current, historical data, status info, and more in real-time and with instant readout even without the need to connect to the BMS, allowing diagnostic at a glance. DVCC closed Loop Control as Well as ATC/ATD Contacts Compatible Victron inverters/chargers and solar chargers are automatically controlled via a connected GX device and DVCC. The ATC/ATD contacts can be used to control other chargers and loads that have a remote on/off port. Programmable Relay The relay can be used either as an alarm relay (combined with the pre-alarm) or to control an alternator via its external regulator (ignition cable). In Alternator ATC mode, the relay will only activate when the contactor is closed. Alternator ATC contact of the alternator opens first and then with a delay of 2 seconds the contactor. These 2 seconds ensure that the alternator is switched off before the battery is disconnected from the system. AUX Terminal The advantage of the onboard auxiliary power supply (1.1 A @ system voltage) is to provide power to specific loads (i.e. a GX device) after the BMS has shut down the loads in the event of a low cell voltage event. If no charge voltage is detected within 5 minutes, the BMS, including the AUX connection switches off. VE.Can and NMEA 2000 Data Communication VE.Can allows for easy connection (standard RJ45 network cable) and communication with a GX device. Since the CANbus protocol is based on NMEA 2000 (and J1939), it is easy to integrate into a marine network and feed a marine MFD with data (requires a VE.Can to NMEA 2000 micro-C male cable). Lynx Distributor Fuse Monitoring Read out the fuse status and receive an alarm in case a fuse is blown. The Lynx Smart BMS monitors up to 4 connected Lynx Distributors and their fuses via VictronConnect or a GX device 1) To reduce the required balancing time, we recommend using as many different batteries in series as possible for the application. 24 V systems are best built using 24 V batteries, and a 48 V system. This System Contains the Following Components: Lynx Distributor with 2 fused paralleled lithium-ion smart batteries. Lynx Smart BMS with BMS, contactor, and battery monitor A second Lynx distributor provides fused connections for inverter/charger(s), loads and chargers (additional modules can be added if more connections are needed) A Cerbo GX (or other GX device) to read out the Lynx Smart BMS and Lynx Distributor data. Power Specifications: Battery Voltage Range: 9 – 60 VDC Maximum Input Voltage: 75 VDC Supported System Voltages: 12, 24, or 48 V Reverse Polarity Protection: No Main Safety Contactor Continuous Current Rating: 1000 A continuous Main Safety Contactor Peak Current Rating: 1200 A for 5 minutes  Power Consumption OFF Mode: 0.3 mA for all system voltages Power Consumption in Standby Mode: Approximately 0.6 W (50 mA at 12 V) Power Consumption in ON Mode: Approx. 2.6 W (217 mA at 12 V) depending on the state of the relays Approximately 4.2 W (350 mA at 12 V) depending on the state of the relays Minimum Load Resistance for Pre-Charging: 10 Ω and above for 12 V systems, 20 Ω and above for 24 V and 48 V systems AUX Output Maximum Current Rating: 1.1 A continuous, protected by resettable fuse Allow-to-Charge Port Maximum Current Rating: 0.5 A at 60 VDC, protected by a resettable fuse Allow-to-Discharge Port Maximum Current Rating: 0.5 A at 60VDC, protected by a resettable fuse Alarm Relay (SPDT) Maximum current Rating: 2 A at 60 VDC Connections: Busbar: M10 (Torque: 17 Nm) VE.Can: RJ45 I/O: Removable multi-connector with screw terminals Battery BTV Cables: Male and female circular 3-pole connector with M8 screw ring Up to 20 batteries can be connected in one system Lynx Distributor fuse monitoring (up to 4 modules) RJ10 (cable ships with each Lynx Distributor) Physical Specifications: Enclosure Material: ABS Enclosure Dimensions (h x w x d): 230 x 180 x 100 mm Unit Weight: 2.7 kg Busbar Material: Tinned copper Busbar Dimensions (h x w): 8 x 30 mm Environmental Specifications: Operating Temperature Range: -40 °C to +60 °C Storage Temperature Range: -40 °C to +60 °C Humidity Max.: 95 % (non-condensing) Protection Class: IP22 Standards Safety: EN-IEC 63000:2018 EMC: EN-IEC 61000-6-3:2007/A1:2011/AC:2012 QMS: NEN-EN-ISO 9001:2015 Please contact your dealer for any returns, repairs or support issues related to this product.

Battery Monitor - BMV-702 - Grey Features: Battery ‘fuel gauge’, time-to-go indicator, and much more The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to take all these variables into account. Next to the basic display options, such as voltage, current and ampere-hours consumed, the BMV-700 series also displays state of charge, time to go, and power consumption in Watts. The BMV-702 features an additional input which can be programmed to measure the voltage (of a second battery), battery temperature or midpoint voltage (see below).  Bluetooth Smart Use the Bluetooth Smart dongle to monitor your batteries on Apple or Android smartphones, tablets, macbooks and other devices.  Easy to install All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for the rear mounting and screws for the front mounting.  Easy to program (with your smartphone!) A quick install menu and a detailed setup menu with scrolling texts assist the user when going through the various settings. Alternatively, choose the fast and easy solution: download the smartphone app (Bluetooth Smart dongle needed)  Standard features - Battery voltage, current, power, ampere-hours consumed and state of charge - Remaining time at the current rate of discharge - Programmable visual and audible alarm - Programmable relay, to turn off non critical loads or to run a generator when needed - 500 Amp quick connect shunt and connection kit - Shunt selection capability up to 10.000 Amps - VE.Direct communication port - Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health - Wide input voltage range: 6,5 – 95V - High current measurement resolution: 10 mA (0,01A) - Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.

BM100 Battery Monitoring Solution The BM100 is a complete system comprising SmartShunt and the veKonvert NMEA 2000 interface. It is part of Digital Yacht’s iSeaSense range of NMEA 2000 boat instruments. With this solution, your multi-function display becomes a sophisticated battery and energy management system. Features Digital Yacht’s BM100 battery monitoring system allows highly accurate DC voltage, current, and capacity measurements, enabling reliable monitoring of your boat’s battery and electrical system. Core to the system is the SmartShunt. It measures battery voltage and current. Based on these measurements, it intelligently calculates the battery’s state of charge and the time to depletion for the remaining charge. It also keeps track of historical data, such as the deepest discharge and average discharge current, as well as the number of charge and discharge cycles. The smart shunt can also monitor the voltage of a 2nd battery, typically dedicated to engine starting. The product is a collaboration between Victron Energy and Digital Yacht. The system utilizes Victron’s proprietary VE.Direct data connectivity as a source for the NMEA 2000 data. The BM100 is part of a wider group of products now introduced by Digital Yacht that bring NMEA 2000 connectivity to Victron systems using the VE.Direct interface. Victron solar panel controllers (MPPTs) and battery monitors can now also interconnect to NMEA 2000 via the veKonvert interface. Monitoring the battery with the BM100 will give important feedback to the user so that remedial measures can be taken when necessary. Doing this will extend battery life. There’s also an optional battery temperature sensor available. The BM100 can also integrate with Digital Yacht’s other NMEA 2000 and wireless instruments, which offer hybrid NMEA 2000 and wireless display options. NMEA 2000 Interface The system features an NMEA 2000 interface, so your navigation multi-function display or plotter can display all key parameters. Modern MFDs from leading manufacturers such as Garmin, Raymarine, Furuno, and Navico allow electrical battery data to be displayed via their NMEA 2000 interface. Alarms and alerts for low capacity and voltage can also be enabled. Bluetooth Interface The BM100 also has a standalone wireless Bluetooth interface, so your mobile phone or iPad can connect and display current, voltage, capacity, additional historical data, state of charge information, and time to go based on remaining battery capacity. Specifications: BM100 solution comes as a complete package with SmartShunt and the veKonvert NMEA 2000 interface Bluetooth interface for setup and detailed analysis, including charge/discharge cycles, state of charge, remaining capacity, and historical data Use your phone/tablet and your NMEA 2000 devices for battery monitoring and management 500A SmartShunt included for the main battery system Monitor the voltage of a separate (eg starter) battery Universal NMEA 2000 gateway for Victron’s popular range of smart battery monitors/SmartShunt using the VE.Direct interface (see compatibility list in the FAQ tab) Enables electrical and battery monitoring and management on compatible multi-function displays (Raymarine, Garmin, Navico, Furuno, etc) Provides battery voltage, charge/discharge current, state of charge, and time to depletion based on a sophisticated algorithm Easy installation, plug ‘n play connectivity, and self-powering from the NMEA 2000 bus Supports alerts generated by the SmartShunt Supports multiple SmartShunts for multi-battery systems Also compatible with other VE.Direct products such as solar MPPT controllers Vekonvert Is Compatible with the Following Victron Products: BMV -700, BMV -702, BMV -700H, BMV-712 Smart, BMV-710H Smart, BMV-712 Smart Rev2, SmartShunt 500A/50mV, SmartShunt 1000A/50mV, SmartShunt 2000A/50mV, and All MPPT Charge Controllers NOTE: veKonvert is not compatible with Victron Chargers and Inverters. It should also not be plugged into the VE.Direct interfaces of any Victron "Consumers" such as Multiplus, Quattro, Cerbo, etc.

Lynx Smart BMS 500 Battery MGMT System for Lithium Smart Batteries The Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature-rich and complete option. Features: Built-in 500A contactor, used as a fall-back safety mechanism and also available as a remote controllable main systems switch Battery monitor, indicating the state of charge percentage and more data. Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell. Bluetooth for use with our VictronConnect App, for setup and monitoring. Local and remote monitoring using a Victron GX device, for example, the Cerbo GX. The Lynx Smart BMS is part of the modular Lynx distribution system. Please contact your dealer for any returns, repairs or support issues related to this product.

BMV-700 Battery Monitor The BMV-700 is a high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery. Features: Battery voltage, current, power, ampere-hours consumed and state of charge  Remaining time at the current rate of discharge  Programmable visual and audible alarm  Programmable relay, to turn off non critical loads or to run a generator when needed  500 Amp quick connect shunt and connection kit  Shunt selection capability up to 10.000 Amps  VE.Direct communication port  Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health  Wide input voltage range: 6,5 – 95V  High current measurement resolution: 10 mA (0,01A)  Low current consumption: 2,9Ah per month (4mA) @12V and 2,2Ah per month (3mA) @ 24V VictronConnect VictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle. Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.

SmartShunt 500A/50MV IP65 Bluetooth Battery Monitor The Smart Battery Shunt The SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as a display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information, and much more. Alternatively, the SmartShunt can be connected and read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter are wanted. The SmartShunt is equipped with Bluetooth, and a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring, or a temperature sensor. Please contact your dealer for any returns, repairs or support issues related to this product.

SmartShunt 1000A/50MV IP65 Bluetooth Battery Monitor The Smart Battery Shunt The SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as a display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information, and much more. Alternatively, the SmartShunt can be connected and read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter are wanted. The SmartShunt is equipped with Bluetooth and a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring, or a temperature sensor. Please contact your dealer for any returns, repairs or support issues related to this product.

SmartShunt 2000A/50MV IP65 Bluetooth Battery Monitor The Smart Battery Shunt The SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as a display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information, and much more. Alternatively, the SmartShunt can be connected and read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter are wanted. The SmartShunt is equipped with Bluetooth and a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring, or a temperature sensor. Please contact your dealer for any returns, repairs or support issues related to this product.

CANNS500 Digital Battery Monitoring Shunt Keep Your Battery Health In Check Boating should be easy and carefree. And with the VETUS CANNS500 shunt, you are one knot closer to a light-hearted summer afternoon on board your electric-powered boat. Specially designed to keep track of your battery dataset, the VETUS CANNS500 Digital Battery Monitoring Shunt will give you that so-desired, worry-free stay on the water. A Know-It-All Solution For Battery Readout Wi-Fi equipped, the VETUS CANNS500 shunt enables you to keep a close eye on the percentage state of charge left in your batteries, as well as power consumption and the estimated remaining boating time. When in range, just connect your smartphone, tablet, or laptop to the CANNS500 shunt to get real-time information on your battery bank. Features: Easy Wi-Fi-connected monitoring with your smartphone, tablet, or laptop Can be connected to an onboard NMEA 2000 network Compatible with CANNME7 VETUS display Suitable for various voltages (12, 24, 36, and 48 VDC) Suitable for currents up to 500 A continuous Real-time battery data readout Integrated sensors for highly accurate reading and timely warning when monitoring an external device Monitor the temperatures and block voltages of up to 4 batteries in 1 battery-bank Compatible with multiple battery types, such as AGM, gel, deep-cycle flooded, and lithium LiFePO4 3 Year Warranty This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.