|
Jog Switch with 2 Sets of Switches
The ComNav Jog Switch is a permanently mounted, watertight, electrical switch specifically designed for marine service. The spring-centred lever is moved to Port or Starboard as desired to provide non follow-up (time dependent) electrical control of the vessel steering system. The Jog Switch can work in conjunction with any autopilot system or can be installed and used as a stand alone system.
|
530.03 |
|
|
GNA 10 Jog Level Adapter
Use the Garmin GNA 10 to connect a jog lever to our Reactor 40 autopilots1 on displacement hull boats. A jog lever is a rugged and simple steering control for workboats or trawlers. Adjust heading hold with the jog lever by pressing it right or left, or put the autopilot into the new Power Steering mode to move the rudder without autopilot guidance. The GNA 10 can also optionally connect to a button and LED light to allow switching between heading hold and standby2. Garmin does not supply the jog lever, button, or LED light.
Specifications:
Cable length: 2.8 meters
Water rating: IPX7
NMEA output: NMEA 2000
NMEA 2000® LEN (Load Equivalency Number): 5 (250mA @ 9VDC)
Operating temperature: -20C to 75C
Supply voltage: Powered by NMEA 2000 bus, 9-32V
Supported Jog Levers:
Kobelt 7170
Jastram JO100/JO300
Simrad S35 (has built-in button and LED status which is supported)
The GNA 10 does not support two-speed jog levers with two sets of switches
Supported Button Types:
DPST OFF-MOM (no diode needed for installation) or
SPST (requires diode for installation)
Max current of 5mA and a max voltage of 12V
Supported LED Types:
LED lights with a current draw of 20mA or less
1 The GNA 10 requires both a compatible Garmin autopilot and Garmin display
2 The GNA 10 can also be used to interface a Reactor 40 autopilot with Jastram digital steering controls
The GNA 10 with jog lever is designed only for use on displacement hull powerboats. It is not compatible with planning hull boats or sailboats.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
242.99 |
|
|
Jog Switch
The ComNav Jog Switch is a permanently mounted, watertight eletrical switch specifically designed for marine service. The spring-centered lever is moved to Port or Starboard as desired to provide non follow-up (time dependent) electrical control of the vessel steering system. The Jog Switch can work in conjunction with any autopilot system or can be installed and used as a stand alone system.
|
477.37 |
|
|
Waterproof Trim Tab Switch - Black/Black Buttons
The rocker-type switch controls are easy to install and operate. the positive action and silver contact points allow for easy bow-up, port, and starboard correction. The wiring for these switches meets federal standards for heat, pull, and insulation. Each set of switches comes color-coded with a switch plate installed. Black Xylon Coated screws, A 20 Amp fuse, and electrical eye fittings, making installation easy, our rocker switches come standard with all trim tab systems and also adapt easily to other brands of trim tabs.
|
117.00 |
|
|
Little Giant Piggyback Diaphragm Switch 599009
Little Giant RS-5 w/18' cord Remote Switch converts manual pumps to automatic operation
RS-5 converts any manual pump, up through 1/2 hp 115 Volt
UL and CSA listing for 115 Volt models only
|
171.28 |
|
|
8086 AC 3 Sources +12 Positions/DC Main +19 Position Toggle Circuit Breaker Panel - White Switches
Features:
Includes set of 30 common AC and 30 common DC labels
All AC and DC buses installed, fully pre-wired
Label backlighting pre-installed
All LEDs installed
Maximum panel Amperage
100 Amperes DC
50 Amperes AC
AC Features:
Two separate AC load groups with transfer switch to combine into one load group
Switch allows Ammeter and Voltmeter to read either AC load group
Reverse polarity indicators on both AC load groups
Ready for installation of optional 4031 AC Isolation Cover
9353, 0-150 Volt AC Voltmeter
9630, 0-50 Amp AC Ammeter
DC Features:
100 Amp C-Series circuit breaker provides main circuit protection and switching for DC branch circuits
8003, 8-16 Volt DC Voltmeter
8017, 0-100 Amp DC Ammeter
Specifications:
AC Positions: Source Selectors +12
DC Positions: Main +19
120 Volts AC
12 Volts DC
(3) 30A - (1) 50A - (6) 15A AC Circuit Breakers
(1) 100A - (13) 15A DC Circuit Breakers
*Combined AC/DC panels require a AC Insulating Cover to meet ABYC Standards
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
1612.97 |
|
|
8084 AC Main +6 Positions/DC Main +15 Positions Toggle Circuit Breaker Panel - White Switches
Features:
Includes set of 30 common AC and 30 common DC labels
All AC and DC buses installed, fully pre-wired
Label backlighting pre-installed
All LEDs installed
Maximum panel Amperage: 100 Amperes DC / 50 Amperes AC
AC Features:
Red reverse polarity indicating LED
Ready for installation of optional 4029 AC Isolation Cover
9353, 0-150 Volt AC Voltmeter
DC Features:
100 Amp C-Series circuit breaker provides main circuit protection and switching for DC branch circuits
8003, 8-16 Volt DC Voltmeter
8017, 0-100 Amp DC Ammeter
Owner upgradeable to 24 Volts with 8240, 18-32 Volt DC Voltmeter
Specifications:
AC Positions: Main +6
DC Positions: Main +15
120 Volts AC
12 Volts DC
(1) 30A - (3) 15A AC Circuit Breakers
(1) 100A - (9) 15A DC Circuit Breakers
*Combined AC/DC panels require a AC Insulating Cover to meet ABYC Standards
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
915.92 |
|
|
March 0150-0125-0200-2.50 Imp Mag Assy Encap W/2.50
|
115.44 |
|
|
March 0150-0125-0200-2.582 Imp Mag Assy W/2.582 Trim
|
115.44 |
|
|
Groco 9R Set Gasket Set Of 2
|
15.80 |
|
|
Melamine Square Dessert Plate - NORTHWIND - 8.2" Set of 6
The square dessert plate from the NORTHWIND collection has a simple but elegant nautical style. This collection has round and square dishes: choose your style! All the dishes in this unbreakable tableware are made from melamine and are decorated, like all the other accessories in the collection, in navy blue and white tones with the compass rose.
NORTHWIND has been the favorite tableware collection for many years and is composed of a large selection of nautical items to make life on board easier and more attractive.
Features:
BPA Free
Break Resistant
Dishwasher Safe
100% Top Melamine
Microwave Safe
Usage:
Melamine products are designed for eating, not cooking. Not for use in the oven or microwave. Suitable for dishwashers. To preserve their shine, avoid using abrasive detergents. To prevent stains caused by tea or coffee, we recommend washing the cups immediately after use. Any design irregularities and differences in these irregularities are part of the production process and should not be considered design faults.
|
64.67 |
|
|
ComNavPassive GPS antenna w/8M cable & TNC connector for X2, X3 and X5 AIS'
|
113.99 |
|
|
HS5 SeaTalkhs Network Switch
The HS5 SeaTalkhs Network Switch works with Raymarine's latest c-Series and e-Series Multifunction Displays and accessories and serves as the central connection point for the SeaTalk High Speed Network.
The HS5 uses the new Raynet waterproof connection system found on c-Series and e-Series displays, and provides a secure, reliable weather tight connection. Up to 5 displays or other peripherals can be connected directly to the HS5 network switch. The 5 ports all support 10 or 100 Megabit speeds when connected to peripherals like displays, scanners, sounder modules or thermal cameras. The 5th port also supports Gigabit speed for interconnecting multiple HS5 switches together on very large networks.
The compact HS5 works on both 12V and 24V dc power systems, and is simple to install with large keyhole mounting slots and front-facing status indicators.
|
342.38 |
|
|
OnDeck™ Relay Switch - 12V
Control your vessel remotely using the OnDeck™ Hub and a relay switch. Add up to five switches to your OnDeck Hub to stay in control.
Verify that the input power for your OnDeck Hub operates between 10 Vdc and 15.6 Vdc to ensure compatibility with your system.
|
44.99 |
|
|
OceanBridge Switch Input Cable
This cable is meant for connecting external switches to OceanLED's OceanBridge.
How to Use
To connect external switches, wire the push-button switches to the OceanBridge Switch Input Cable. Then, connect the switch input cable plug to the OceanBridge switch input connector. Keep in mind that supplementary wiring will be needed to establish the connection for the 12/24V DC power to the switch installation.
|
76.37 |
|