|
Cruiser Series Battery Selector Switch with AFD
Part No. 2100
Description
Continuous Amps: 230
Momentary Amps: 345
Cable Lug Size: 3/8"
Color: Orange
Dimensions: 5-1/2"W x 2-5/8"
Product Features
Alternator field disconnect (AFD) allows selection of any position, including "off" without damage to alternator or electrical system
Polycarbonate case
For 6, 12, 24 or 36 volt systems
One year Warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
56.10 |
|
|
Cruiser Series Battery Selector Switch without AFD
This battery switch can be used on 6, 12, 24 or 36V systems.
Features:
Polycarbonate case
Surface mount
Cable Lug Size: 3/8"
Dimensions: 5.50" x 2.63"
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
48.34 |
|
|
Battery Selector Switch
Part No. 2111A
Features
New ergonomically styled turn knob provides easy On/Off switching
Updated color scheme and graphics make it easier to determine switch status
Longer stud lengths for improved assembly and easier cable routing
Built with heavy-duty copper sweep contacts to ensure positive circuit control
Rugged internal components protected by a tough, impact resistant polycarbonate housing that is impervious to the elements
One year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
28.78 |
|
|
Medium Duty Battery Selector Switch w/Key Lock
Perko's 8501 Series battery selector switches are among the most popular battery switches ever produced. Their use of the traditional Perko bolt circle makes for easy installation, whether new or as a replacement. These switches can be mounted in numerous locations. And as ignition protected switches, they can be installed in the engine rooms of gasoline powered boats.
In addition to doing everything a battery disconnect switch does, battery selector switches permit battery selection (of two or more batteries) for specific purposes including starting engines, running accessories or even recharging. They allow for the use of one or more batteries in systems with one or more engines and facilitate putting batteries in parallel for emergency starting when one or both batteries are substantially discharged.
Perko battery switches are designed for surface mounting. Standard duty switches have a bright red polycarbonate housing for safety with a large easy-to-turn black knob. The housing of the heavy duty switches are red fiber-reinforced polycarbonate. Selector switches are designed with a "make before break" feature. This allows switching between the "1", the "ALL" and the "2" positions while the engine is running. Models with an "Alternator Field Disconnect" feature offer protection for Non-Unitized Alternators should the switch accidentally be turned to the "OFF" position with the engine running.
Versions of the 8501 Series switches offer additional features such as alternator disconnect and key lock security.
The 90° rotation feature allows users to feel the switches' position in no light situations and the classic shape of the knob makes it easy to turn.
High conductivity studs are long enough to handle more than 1 cable and strong enough for torque needed for secure connections. Optional spacer ring (PN 0462DP0RED) allows for the use of larger cables.
Specifications:
Diameter: 5-1/4"
Depth: 2-5/8"
For use with 6 to 50 Volt Marine Electrical Systems
Capacity - 250 AMPS Continuous, 360 AMPS Intermittent
When used with Non-Unitized Alternators, these models will interrupt the field current (reducing the possibility of damage) if turned "OFF" with the engine running
|
73.54 |
|
|
Diesel Power Battery Selector Switch
Product Features
Polycarbonate case
For 6, 12, 24 or 36 Volt systems
Alternator field disconnect (AFD) allowing selection of any position including "off", without damage to alternator or electrical system
One year warranty
Specifications:
Continuous Amps: 360
Momentary Amps: 600
Cable Lug Size: 1/2"
Color: Gray
Dimensions: 5-1/2" sq x 3-1/2"H
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
129.80 |
|
|
Battery Selector Switch with AFD
Part No. 2110A
Description
Continuous Amps: 230
Momentary Amps: 345
Dimensions: 5"D x 2-3/4"H
Product Features
Alternator field disconnect (AFD) allows selection of any positions, including "off" without damage to alternator or electrical system. AFD is required on some electrical systems.
Heavy duty copper sweep contacts
"Make before break" contacts allow selection of all positions except "off" while engine is running
Use with 6, 12, 24 or 36 volt systems
New design is easy to retrofit into existing hole patterns
Built-in skirt protects connections
Exclusive flat 360 degree "sweep" contact design provides up to 60% more contact area than other switch designs
Surface or rear panel mounting
Marine grade construction
One year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
34.32 |
|
|
Compact Battery Selector & Main Disconnect Switches
Ignition Protected
For use with 12, 24 and 32 volt marine electrical systems
Higher Rating Than Popular 8500 Series Switches
Same bolt patterns as popular 8500 series
Smooth, positive position selector
Compact, Medium Duty Battery Selector Switch
|
62.24 |
|
|
Compact Battery Selector & Main Disconnect Switches
Ignition Protected
For use with 12, 24 and 32 volt marine electrical systems
Higher Rating Than Popular 8500 Series Switches
Same bolt patterns as popular 8500 series
Smooth, positive position selector
Compact, Medium Duty Battery Selector Switch w/ Key Lock
|
73.54 |
|
|
Mini Battery Selector Switch
The 701S is the most compact selector switch available on the market. While BEP recommends isolated battery systems as outlined with our distribution clusters, the 701S provides a simple economical way of separating two batteries. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.
Housed in the same dimensions as the 701, and includes the same removable side plates and back cover
Please note selector switches will not separate electronics from harmful engine starting spikes
Tin-plated copper studs and nuts
Ignition-protected
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
35.83 |
|
|
Heavy-Duty Battery Selector Switch
The 721 Battery Selector Switch is our heavy duty selector switch. Housed in the same module as the 720, it includes the same removable plates and back cover. While BEP Marine recommends isolated battery systems as outlined with our distribution clusters, the 721 offers a simple economical way of separating two batteries. Please note selector switches will not separate electronics from harmful engine starting spikes.
Specifications:
DC Voltage: 48
Stud Size (Imperial): 3 x 3/8"
Stud Size (Metric): 2 x 10mm
Continuous Rating: 350
Intermittent Rating: 500
Cranking Rating: 1500
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
59.10 |
|
|
Pro Installer 400A EZ-Mount Battery Selector Switch (1-2-Both-Off)
As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches.
Tested to UL1107 ignition protection, CE
Tinned copper 10mm (3/8") studs
Stainless steel washers/nuts
Fiber reinforced plastics
400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking
Waterproof to IP66
Same interconnection height as Pro Installer
Removable knob allows isolation during servicing
3 removable sideplates for protection
Industry standard 3.85" x 3.85" footprint
Specifications
Mounting: Surface Only
Voltage: 48v DC (for 12-48v systems)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: 1-2-Both-Off
Stud: 3x 10 mm (3.8")
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
58.00 |
|
|
Medium Duty Battery Selector Switches
Ignition Protected
For use with 12, 24 and 32 volt marine electrical systems
Capacity - 250 AMPS continuous, 360 Amp Intermittent
Medium Duty Battery Selector Switch w/ Alternator Field Disconnect
w/o Key Lock
|
74.88 |
|
|
Medium Duty Battery Selector Switches
Ignition Protected
For use with 12, 24 and 32 volt marine electrical systems
Capacity - 250 AMPS continuous, 360 Amp Intermittent
Medium Duty Battery Selector Switch w/ Alternator Field Disconnect
w Key Lock
|
80.88 |
|
|
Dual Battery Selector Switch - Cup Mount
The Perko Dual Battery Selector Switch allows the addition of an extra battery for accessories. This switch provides the flexibility of selection between batteries or combined operation of both batteries in parallel for starting or charging. It can also serve as an emergency main disconnect switch in the event of an electrical problem. All models are make before break design and are ignition protected.
Features:
For two or more batteries
Unique oval shape mounts in a round hole
Removable actuator key
|
63.20 |
|
|
Heavy Duty Battery Switch
Ignition Protected
For use with 6, 12, 24 and 32 volt marine electrical systems
capacity - rated 380 amps continuous,
850 amps intermittent (5 mins on, 5 mins off)
Heavy Duty Battery Selector Switch w/ Alternator Field Disconnect
|
186.97 |
|