|
AL7001CR
The AL7001CR (1-3/8"ID) is the solution for boats with a tower or when a lower angle is desired. It has a slightly larger footprint (4"x 7"). Ruggedly constructed from marine grade anodized aluminum. It can be easily attached above or below the standing platform or any flat surface. It comes in a standard angle of 22 degrees that gives it a low rise. Anodized in Bright Silver it is as strong as it is attractive. It accepts all the same poles as the AL7000 series holders.
|
220.15 |
|
|
MX8000CR
Adjustable Angle holders MX8000CR (1-5/8" ID) are our strongest and most versatile holders. The three-point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18".
Recommended poles for MX8000CR
MX8719CR - 19 ft MX Step- Tube Style
MX8716CX - 16 ft MX Step- Tube Style - Single Spreader
MX8719CX - 19 ft MX Step- Tube Style - Single Spreader
MX8720CX - 20 ft MX Step- Tube Style - Double Spreader
MX8722CX - 22 ft MX Step- Tube Style - Single Spreader or Double Spreader
|
516.32 |
|
|
Outrigger Holder Reducer - 1-5/8" to 1-1/2" - Pair
Downsize your outrigger holders
Reduce from 1-5/8" to 1-1/2"
|
58.68 |
|
|
MX7000CR
Adjustable Angle holders MX7000CR (1-1/2" ID) are our strongest and most versatile holders. The three point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18".
Recomended poles for MX7000CR
AO8716CR - 16 ft Center Rigger (Mk II)
AO8718CR - 18 ft Center Rigger (Mk II)
MX8712CR - 12 ft MX Step- Tube Style
MX8715CR - 15 ft MX Step- Tube Style
MX8718CR - 18 ft MX Step- Tube Style
MX8716CX - 16 ft MX Step- Tube Style - Single Spreader
MX8720CX - 20 ft MX Step- Tube Style - Double Spreader
|
502.62 |
|
|
PSS Shaft Seal 1-3/8" Shaft 2-1/4" Tube
Shaft Diameter: 1-3/8"
Stern Tube Diameter (D): 2-1/4" to 2-3/8"
Total Length (A): 7.38"
Total Length (compressed) (Compressed A): 6.38"
Rotor Diameter (B): 2.875"
Carbon Cuff Diameter (C): 2.5"
Stern Cuff Length (E): 1.5"
The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).
The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.
**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."
Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.
The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.
|
324.00 |
|
|
The Original Wishbone Outrigger Holder
The Original Wishbone Style Outrigger Holder has been in production for over 45 years. Setting the standard for the industry, our "Junior" outrigger holder has often been imitated, but never equaled. Its ease of operation, adjustable fishing angle, ability to lay down for bridges and small footprint makes it the ideal holder for a multitude of boats.
Durability was the watchword at its conception. You won't find plastic parts in this holder. Constructed of heavy duty brass forgings, heavy wall brass pipe and a stainless steel main tube, it epitomizes strength and reliability. The three point mounting system provides maximum strength and distributes the stress to the mounting surface over a wide area. This holder can be mounted vertically or angled toward the stern. Somewhere between twenty to thirty five degrees is normal.
Model OH226S is for use with our deluxe 19ft. single spreader poles and non-spreader poles up to 22ft.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
1859.68 |
|
|
AL7211CR
The AL7211CR (1-3/8"ID) is the perfect holder for boats in the 16 to 31 ft range. Its economical price and small footprint (3"x 5") make it our most popular center rigger holder. The receiving tube of this marine grade anodized holder is set at a 45 degree angle. This is the perfect angle for boats where the mounting position is low and the cockpit is not extremely deep (e.g. mounting on T-Tops, Hard Tops, or Fly-Bridges). Compatible poles are 12 or 14ft in length and come standard in bright silver anodized finish with a Black Spike.
Recomended poles for AL7211CR
AO8712CR - 12 ft Center Rigger (Mk II)
AO8714CR - 14 ft Center Rigger (Mk II)
MX8712CR - 12 ft MX Step- Tube Style
|
108.00 |
|
|
MX Pro Series Fixed Angle Center Rigger Holder - 22° - 1.5" ID - Bright Silver
The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by.
MX Pro Series (1-1/2"ID) is the solution for boats with a tower or when a lower angle is desired
Slightly larger footprint (5"x 7")
Ruggedly constructed from marine grade anodized aluminum
Can be easily attached above or below the standing platform or any flat surface
Anodized in Bright Silver it is as strong as it is attractive
|
261.70 |
|
|
MX Pro Series Fixed Angle Center Rigger Holder - 30° - 1.5" ID - Bright Silver
The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by.
MX Pro Series (1-1/2"ID) is the solution for boats with a tower or when a lower angle is desired
Slightly larger footprint (5"x 7")
Ruggedly constructed from marine grade anodized aluminum
Can be easily attached above or below the standing platform or any flat surface
Anodized in Bright Silver it is as strong as it is attractive
|
261.70 |
|
|
MX Pro Series Fixed Angle Center Rigger Holder - 45° - 1.5" ID - Bright Silver
The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by.
MX Pro Series (1-1/2"ID) is the solution for boats with a tower or when a lower angle is desired
Slightly larger footprint (5"x 7")
Ruggedly constructed from marine grade anodized aluminum
Can be easily attached above or below the standing platform or any flat surface
Anodized in Bright Silver it is as strong as it is attractive
|
261.70 |
|
|
AL7301CR
Fits 1.050" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|
|
AL7302CR
Fits 1.315" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|
|
AL7303CR
Fits 1.660" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|
|
AL7304CR
Fits 1.900" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|
|
Center Rigger Holder - 1-5/16" IPS Pipe - 1-1/8" Holder
Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. Fits 1" Pipe Size.
|
88.03 |
|