Submersible Pressure Transducer 0-3 PSI Maretron’s submersible pressure transducers indicate tank levels and can be installed directly in the tank. Please follow these instructions to mount and connect a submersible pressure transducer to an NMEA 2000® network via a Maretron FPM100 Fluid Pressure Monitor. Maretron recommends one of two methods for mounting a submersible pressure transducer in a tank: 1) without a restraining tube, and 2) with a restraining tube. The submersible pressure transducers are designed for a tank with a 5-hole SAE J1810 fitting at the top. Install the mounting plate with cord grip onto the transducer cable, with the rounded hex section of the cord grip facing away from the transducer. Lower the pressure transducer into the tank such that the transducer lies at the lowest point of the tank and tighten the cord grip to secure the cable. On a tank with a flat bottom, the transducer may slide from side to side with the motion of the vessel but will not rotate due to the stiffness of the cable. It is also possible to mount the pressure transducer inside a restraining or focus tube (sold separately, Maretron part number TFT-5H). Pressure Transducer Mounting Connect the two wires of the pressure transducer to a free pressure monitoring channel. Connect the red wire from the pressure transducer to the channel's positive (+) terminal and connect the black wire from the pressure transducer to the negative (-) terminal of the channel. The example in Figure 1 shows the pressure transducer connected to switch channel 0, with the white wire connected to "P0+" and the brown wire connected to "P0-." Submersible pressure transducers have a small plastic vent tube in the connecting cable. Use a Maretron DSM Series Display (firmware 1.4.7 or higher) or a PC running Maretron’s N2KAnalyzer software (version 1.4.19 or higher) to configure the connected channel(s) on the FPM100. Supply power to the NMEA 2000 network and verify that the pressure channel indicates a valid pressure reading. Specifications: Operating Range: 0 to 3 PSI (0.207 bar) Depth Range (Water): 83.1” (2.11 m) Depth Range Diesel (820 kg/m3): 101.3” (2.57 m) Depth Range Gasoline/Petrol (750 kg/m3): 110.8” (2.81 m) Cable Length: 17 ft (5.18 m) Sensor Type: Gauge (Vent Tube) Output: 4 – 20 mA current loop, loop powered Excitation Voltage: 8 VDC to 28 VDC Compatible Fluids / Gases: Diesel, Diesel Exhaust Fluid (DEF), Gasoline/Petrol, Hydraulic Fluid, Kerosene, Motor Oil, Fresh Water, Sea Water, Waste Water Operating Temperature: 14 degrees F to 158 degrees F (-10 degrees C to 80 degrees C) Storage Temperature: -4 degrees F to 176 degrees F (-20 degrees C to 80 degrees C) Accuracy: ±0.3% Full Scale typ. at 25°C Total Error Band (TEB): ±1.0% Full Scale typ. (-10 degrees C to 70 degrees C) Non-Linearity, Hysteresis (NLH): ±0.2% Full-Scale typ. Best Straight Line (BSL) at 25°C Temperature Compensation: 23 degrees F to 122 degrees F (0 degrees C to 50 degrees C) Accuracy: ±1% Full Scale Linearity: 0.5% Full Scale Repeatability: 0.05% Full Scale Full-Scale Thermal Error: 0.04% Full Scale/°F (0.07% Full Scale/degrees C) Long-Term Stability: 0.2% Full Scale/year Response Time: 150ms Proof Pressure: 2 × Full Scale Burst Pressure: 3 × Full Scale Reverse Voltage Protection: ± 30V for 3 minutes Construction: 316L stainless steel body and diaphragm, polyether polyurethane cable, chloroprene boot EMC Compatibility: 10 Volts/meter per EN 61000-4-3 Weight: 24.8oz (703g)

Submersible Pressure Transducer - 0-1.5 PSI The submersible pressure transducers are used together with Maretron's Fluid Pressure Monitor (FPM100), which allows tank fluid level to be broadcast over an NMEA 2000® network where it can be monitored from any compatible NMEA 2000® display. When used together with Maretron displays, alerts can be set to inform the user of low or high tank levels. Users can be notified through emails or text messages about their tank levels when not onboard the vessel. Additionally, the tank levels can be stored using Maretron's data recorder (VDR100) for later analysis.

Submersible Pressure Transducer - 0 to 5 PSI The submersible pressure transducers are used together with Maretron's Fluid Pressure Monitor (FPM100), whichallows tank fluid level to be broadcast over an NMEA 2000® network where it can be monitored from any compatible NMEA 2000® display. When used together with Maretron displays, alerts can be set so the user can be informed of low or high tank levels. And when not on-board the vessel, users can be notified through emails or text messages about theirtank levels. Additionally, the tank levels can be stored using Maretron's data recorder (VDR100) for later analysis. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Galley Maid Pressure Gauge 0-60 PSI Picture is a representation of a 0 to 60 PSI gage.

Pressure Transducer - 0 to 5000 PSI This pressure transducer is designed to connect to the NMEA 2000® network via a Maretron FPM100 Fluid Pressure Module. Specifications: Range: 0 to 5000 PSI (344.74 bar) Accuracy: +/- 0.5% Full Scale Type: Absolute (no vent tube) Installation: All Maretron pressure transducer assemblies are equipped with a 1/4 in. NPT male threaded fitting. Install the pressure transducer to a 1/4 in. NPT female fitting on the system or tank is to be monitored with a maximum torque of 150 in-lbs (16.95 Nm). If you are monitoring a system where pressure spikes or transients will occur, or where the pressure will exceed the maximum pressure rating of the pressure transducer, install a Pressure Snubber (PT-SNUB-01) onto the system being monitored first, then install the pressure transducer to the female port on the pressure snubber.

Pressure Transducer 0 to 50 PSI All Maretron pressure transducer assemblies are equipped with a 1/4” NPT male threaded fitting. Install the pressure transducer to a ¼” NPT female fitting on the system or tank to be monitored with a maximum torque of 150 in-lbs (16.95 Nm). If you are monitoring a system where pressure spikes or transients will occur, or where the pressure will exceed the maximum pressure rating of the pressure transducer, install a Pressure Snubber (PT-SNUB-01) onto the system being monitored first, then install the pressure transducer to the female port on the pressure snubber. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Pressure Transducer 0 to 5 PSI - for FPM100 Fluid Pressure Monitor WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Pressure Transducer 0 to 1.5 PSI For use with FPM100 Fluid Pressure Monitor WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Pressure Transducer 0 to 3 PSI - for the FPM100 Fluid Pressure Monitor WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

2" Oil Pressure Gauge (0-100 PSI) A pressure gauge operates by sending a low amperage current through the gauge's meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the change in pressure. Includes fire orange pointer, black aluminum bezel, flat glass lens, case with locator keyway to ensure proper installation and perimeter lighted black dial with stylish white graphics. Available for MG systems, J1939 CAN Bus or J1939 Stand-Alone systems and mechanical types. 2" - Hole Size: 2.0625" (53mm) Specifications: Standard (100-200°F) Scratch Resistant Lens Black Aluminum Bezel Orange Contoured Pointer

Jabsco 30472-1000 Pressure Gauge 0-60 Psi  

9 M SILR Y Dual Side Image Transducer Adapter Cable f/HELIX  Y Cable - Separates Side Imaging into Left and Right Side Beams - for Side Imaging products only.  Allows the use of two side imaging transducers with one unit without the need for a transducer switch.  Y Cable - Separates Side Imaging into Left and Right Side Beams - for Side Imaging products only.  Allows the use of two side imaging transducers with one unit without the need for a transducer switch.  Used in applications where the a plastic thru the hull transducer is required on a boat with a deep V hull or the motor or other items on the transom of the boat may block one side of the transducer and distort readings.    30" length. Supports MEGA Side Imaging. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Kronos 2" Water Pressure Gauge Kit - 30 PSI Polished Stainless Steel bezel, flat glass lens, perimeter lighted spun aluminum dial with Gold and Black graphics. Gold increments and Logo on dial are Embossed.  All instruments include two piece Newport pointer with White hub.  A pressure gauge operates by sending a low amperage current through the gauge's meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc... As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the change in pressure. 2" - Hole size: 2.0625" (53mm) Specifications: Flat Scratch Resistant Lens Polished Stainless Steel bezel LED Illuminating around the Perimeter of the Dial Newport style White Pointer Dual Scale - Imperial and Metric In the Box: 2” 30 PSI Kronos SS Water Pressure gauge 1/8” NPT Adapter w/locktite VS 516 Mounting hardware 15’ Tubing Factory P/N OP1171 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Newport SS 2" Oil Pressure Gauge - 0 to 80 PSI  The Newport Stainless Steel (SS) family of marine gauges is a classic style of gauge, engineered to be the new Modern Retro.   Designed with the latest fog resistant features, this Retro Style gauge far surpasses all expectations.  Perimeter lighting makes reading these gauges easy to read Day/Night.  Features:  Perimeter lighted Retro White Dial Black and Gray Graphics  Domed fog resistant lens  Two-piece Black pointers  Hand-polished Stainless Steel bezel Studded connection for ring terminals Red illuminated edge-lighting Technical Specifications:  Operating Range  - 0 to 80 PSI 2.06" (53 mm) Mounting hole Operating Voltage - 12/24 V In the box: Gauge Mounting Hardware Installation Manual Factory P/N GP8159 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Newport SS 2" Oil Pressure Gauge - 0 to 100 PSI The Newport Stainless Steel (SS) family of marine gauges is a classic style of gauge, engineered to be the new Modern Retro.   Designed with the latest fog resistant features, this Retro Style gauge far surpasses all expectations.  Perimeter lighting makes reading these gauges easy to read Day/Night.  Features:  Perimeter lighted Retro White Dial Black and Gray Graphics  Domed fog resistant lens  Two-piece Black pointers  Hand-polished Stainless Steel bezel Studded connection for ring terminals Red illuminated edge-lighting Technical Specifications:  Operating Range  - 0 to 100 PSI 2.06" (53 mm) Mounting hole Operating Voltage - 12/24 V In the Box: Gauge Mounting Hardware Installation Manual Factory P/N GP8185 *Sold as an Individual ** Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.