|
Wiring Harness, 60 amp (712A, 912, 915, T2400, T4000, T3200PO, AP3500)
|
84.16 |
|
|
Circuit Breaker, 60 amp (712A, 912, 915, T2400, T4000, T3200PO, ST712, SH12HBM, AP3500)
|
23.65 |
|
|
Plug (712A, 912, 915, T2400, T4000, T3200PO, ST712, BH12, SH12HBM, AP3500)
|
16.27 |
|
|
Socket (712A, 912, 915, T2400, T4000, T3200PO, ST712, BH12, SH12HBM, AP3500)
|
14.77 |
|
|
Switch (712A, 912, 915, T2400, T4000, T3200PO, ST712)
|
49.85 |
|
|
40' x 7/32" Replacement Galvanized Cable with Hook
For all manual and electric trailer winches. High chromium content and added nickel make these cables virtually impervious to corrosion and add years of service. Ideal for any winch using 7/32 inches diameter cable, designed for handling boats up to 11,500 pounds, superior 7 x 19 strand cable construction for maximum pulling strength. Complete installation instructions included. Available with heavy duty zinc plated pulley block.
Features:
Galvanized cable with hook
40 feet x 7/32 inches
Replacement for RC30, RC23, 712A, 912, 915 T2400 and AP3500 winches
|
60.29 |
|
|
Thrust Bearing, Thrust Washers, and Springs (712A, 912, T2400, T4000, ST712, VS190, AP3500)
|
60.25 |
|
|
Male Plug & Socket for 712, 912, 915, RC30 & RC23
Replacement wiring harness plug to fit the socket. For Powerwinch Models: 712, 912, 915, RC30, and RC23.
|
26.63 |
|
|
Wire Harness - High Power f/40" - 50" Light Bar
This 13' wiring harness is designed to connect a single 40"-50" LED light bar to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: 50" E-Series, 50" SR-Series.
Features:
14 AWG Wire
Deutsch Connector
Inline Fuse Holder
|
45.37 |
|
|
Wire Harness f/10"-30" Light Bar
This 11' wiring harness is designed to connect a single 10"-30" LED light bar to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: 10" E-Series, 10" SR-Series, 20" E-Series, 20" SR-Series, 30" E-Series, 30" SR-Series, 40" E-Series, 40" SR-Series.
Features:
16 AWG Wire
Deutsch Connector
Inline Fuse Holder
12 Volt Relay
|
40.12 |
|
|
Wire Harness f/4"-6" Light Bar
This 11' wiring harness is designed to connect a single LED light to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: Dually (Single), D2 (Single), 4" E-Series, 6" E-Series, 4" SR-Series, 6" SR-Series.
Features:
18 AWG Wire
Deutsch Connector
Inline Fuse Holder
|
32.09 |
|
|
Wire Harness f/Dually Pair
This 14' wiring harness is designed to connect a pair of Dually LED lights to your 12V electrical system. It features battery terminals on one end and Deutsch connectors on the other to connect to the lights. It incorporates an inline fuse holder, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: Dually (Pair).
Features:
18 AWG Wire
Deutsch Connector
Inline Fuse Holder
|
32.09 |
|
|
Wire Harness f/D2 Pair
This 14' wiring harness is designed to connect a pair of D2 LED lights to your 12V electrical system. It features battery terminals on one end and Deutsch connectors on the other to connect to the lights. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: D2 (Pair).
Features:
18 AWG Wire
Deutsch Connector
Inline Fuse Holder
|
31.92 |
|
|
PP4408 PowerPod Pre-Cut f/Simrad GO7 & B&G Vulcan 7
PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base.
The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV.
PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels.
All PowerPods Include:
Acrylic capped ABS plastic
Chromed stainless steel tamper-poof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Swivel Base with large pass-through for wire harness
|
322.90 |
|
|
PP4410 PowerPod Pre-Cut for Garmin STRIKER™ 5dv (Requires Flush Mount Kit Garmin Part)
PP4400 Series, PowerPods for Power are a better option than bracket mounting. PowerPods provide a clean look for flush mounting with the advantage of a swivel base.
The trunion bracket that is supplied with most electronics is not optimal. PowerPods have the advantage of protecting the back of the electronics from harsh saltwater spray. Most manufacturers do an excellent job of protecting the face of the display from water intrusion with sealed rubber push buttons. The back is generally not waterproof. They are expecting you to flush mount it into the console or a NavPod. The PowerPod also protects the plastic connectors and wires from deterioration caused by long term exposure to UV.
PowerPods for Sail are for mounting on a flat surface. Perhaps under the dodger or aft end of the cockpit table especially on boats with dual wheels.
All PowerPods Include:
Acrylic capped ABS plastic
Chromed stainless steel tamper-poof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Swivel Base with large pass-through for wire harness
|
322.90 |
|