Rule In-Line Blower - 3" Ducting Part Number: 140 Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule? in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets. Features Efficient high-volume air flow Quiet operation Low amp draw Slip-on inlet and outlet ducting connections Sealed motor shaft for moisture protection Corrosion resistant nickel-plated motor housing IMCI (CE) USCG 183.410 Compliant: Ignition protected Applications: Race cars and helmet ventilation Bus ventilation (engine and bathroom fumes) Prison van ventilation (cooling, air-freshening) Blow-up signs and mascots Tanning booths Building ventilation Specifications Approvals: CE Dimensions (H x W x D): 76 x 127 x 81 (mm) ElectricalCharacteristics: 2.9 Amp Flow Rate (US gallons & litres): 135 CFM @ Open Flow Fuse Size: 4 (amp) Product Inlet Fitting: 3" (76 mm) Ducting Product Outlet Fitting: 3" (76 mm) Ducting Voltage: 13.6 (Vdc) WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

3" In-Line Blower Inlet/Outlet - 3" CFM - 158 Johnson Pump in-line blowers provide ventilation for bilges, engine compartments, galleys, and heads. Made from high quality ABS plastic construction, corrosion resistant motors, and premium electrical connections completes these blowers Five blade, quiet, highly efficient, and reliable operation will provide years of long life Compact and with mounting feet makes it easy to install on any flat surface

Rule In-Line Blower - 4" Ducting Part Number: 240 Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule® in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets. Features Efficient high-volume air flow Quiet operation Low amp draw Slip-on inlet and outlet ducting connections Sealed motor shaft for moisture protection Corrosion resistant nickel-plated motor housing IMCI (CE) USCG 183.410 Compliant: Ignition protected Applications: Race cars and helmet ventilation Bus ventilation (engine and bathroom fumes) Prison van ventilation (cooling, air-freshening) Blow-up signs and mascots Tanning booths Building ventilation Specifications Approvals: CE Dimensions (H x W x D): 102 x 152 x 106 (mm) ElectricalCharacteristics: 4.3 Amp Flow Rate (US gallons & litres): 235 CFM @ Open Flow Fuse Size: 7 (amp) Product Inlet Fitting: 4" (102 mm) Ducting Product Outlet Fitting: 4" (102 mm) Ducting Voltage: 13.6 (Vdc) WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

4" In-Line Blower Inlet/Outlet - 4" CFM - 240 Johnson Pump in-line blowers provide ventilation for bilges, engine compartments, galleys, and heads. Made from high quality ABS plastic construction, corrosion resistant motors, and premium electrical connections completes these blowers Five blade, quiet, highly efficient, and reliable operation will provide years of long life Compact and with mounting feet makes it easy to install on any flat surface

Turbo 4000 Series II In-Line Blower Part #: 1749-4 Attwood's improved Turbo 4000 Series II sets the standard for in-line blower performance. Utilizing advanced fan blade design techniques, Attwood has developed a blower system that matches air flow of existing in-line blowers at a significantly reduced noise level. The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size. Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads. Features: Nickel-plated motor can for corrosion resistance Stiffening ribs to reduce housing distortion Motor cap to seal wires and motor for water resistance Five-blade fan maximize airflow and efficiency Tabs in intake and exhaust hold ventilation hose/clamp firmly in place Low amp draw motor for longer blower and battery life Built-in mounting feet allow easy vertical or horizontal install 3-Year Warranty WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Turbo 3000 Series In-Line Blower Part #: 1733-4 The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size. Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads with optional MP1 molded rubber connectors. Improved 3" design. Features: Nickel-plated motor can for corrosion resistance Stiffening ribs to reduce housing distortion Motor cap to seal wires and motor for water resistance Five-blade fan maximize airflow and efficiency Tabs in intake and exhaust hold ventilation hose/clamp firmly in place Low amp draw motor for longer blower and battery life Built-in mounting feet allow easy vertical or horizontal install WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

iL200 In-Line & Submersible Pump 12V Centrifugal submersible and inline pump; Suitable for fresh or salt water Water transfer, deck shower, or deck wash Water Systems to 60°C Intermittent rating of 20 minutes. Should not be run dry for long periods Specifications Output: up to 12.7 litres/minute at up to 1bar (2.8 gallons/minute at 14psi) Connections: 1/2" (12.7mm) and 3/4" (19mm) Hose Dimensions: (L x Diameter) 130 x 36 (mm) Amp Draw: 2.8 (amp) Packed Size: 190.0 x 50.0 x 130.0 mm (LxHxW) Weight: 206 (g) WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

3" Blue Polyduct Blower Hose - Sold by the Foot Trident Polyduct is the most flexible, crush proof and rugged blower duct hose for heat, ventilation, and air conditioning* (HVAC). Heavy Duty polypropylene hose, reinforced with a flexible polypropylene rod helix. Features: Sold by the foot Excellent flexibility & compressibility Excellent resistance to crushing, flex fatigue, tearing, and moisture  Stomp on it and it returns to shape without damage  Shove it thru tight openings and overheads and it delivers full airflow Application: Rugged blower duct hose for heat, ventilation, and air conditioning Specifications:  Temperature Range: -40°F to +225°F (-40°C to 107°C) (when insulated) Inner Diameter (inch): 3" *Meets FMVSS 302 flame resistance

Air Blower 1000 Inline 165 - 12V 7″ in-line mounted marine ventilation 12V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 165mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance.  Features: Weight: 1.2 kg/2 lbs Dimensions: 165/6.5L x 220/8.7H x 178/7W mm/in  Type: 7" In-Line For continous duty  7A fuse *Certification: CE marked ISO 9097:1991 Marine (small craft electrical fans), ISO8846 1990 (ignition protection), ISO 10133 2000 (electrical systems), EN55014-1 2006 (2004/108EC)

iL200 Plus In-Line & Submersible Pump 12V Centrifugal submersible and inline pump; Suitable for diesel, fresh and salt water Quick diesel transfer with no spillage Bait tank aeration, diesel transfer, water transfer Water Systems to 80°C Continuous rating but should not be run dry for long periods Specifications Output: up to 12.7 litres/minute at up to .75bar (2.8 gallons/minute at 11psi) Connections: 1/2" (12.7mm) Hose Dimensions (L x H): 142 x 38 (mm) Amp Draw: 2.5 (amp) Weight: 260 (g) WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

IL200 Plus In-Line Submersible Pump - 24V - 2.8GPM Centrifugal submersible and inline pump. Features:  Cable Length: 1(m) Connections: 1/2" (12.7mm) Hose Dimensions: 142mm long, 38mm diameter Maximum Current: 1.5(amps) Output: up to 12.7 litres/minute at up to .75bar (2.8 gallons/minute at 11psi) Suitable for diesel, fresh and salt water Quick diesel transfer with no spillage Bait tank aeration, diesel transfer, water transfer. Water Systems to 80 ºC Intermittent light duty Motor life approx 250 hours Actual Weight: 0.33 Kg  (Approx. 0.53 Kg packed)

Exit Plate/Flat for up to 3/4" Line Specifications: Halyard Size 3/4" (19 mm) Mast Stat Opening 3-1/4"x 1" (83 mm x 25 mm) Fasteners (4), #10 RH (5 mm) Weight 1 oz. (28 g)

In-Line Check Valve 1"-1 1/2" Stepped Connection All Whale bilge switches, non-return valves, strainers and pipework fittings are designed and manufacturers with highest quality at heart. Combine these accessories with your whale bilge pump for a robust bilge system tailored to your vessel. LV1215 In-line Check Valve 25mm / 38mm (1"/ 1 1/2") Stepped Connection WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Series 20 Ball Bearing Block - Double, In-Line Features: Low friction High static and dynamic load capacity Lightweight Precision molded Acetal sheaves running on stainless steel or Torlon® ball bearings provide high performance & low friction. Applications: Dinghy control lines Dinghy vangs Cunninghams Traveller controls Dinghy barber haulers Spinnaker pole launching systems Materials: Stainless Steel ball bearings UV stabilized Acetal sheave Grade 316 Stainless Steel load strap and head fitting Impact and UV resistant, fiber reinforced Nylon cheeks

Air Blower 1000 Inline 165 - 24V 7″ in-line mounted marine ventilation 24V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 165mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance.  Features: Weight: 1.2 kg/2 lbs Dimensions: 165/6.5L x 220/8.7H x 178/7W mm/in  Type: 7" In-Line For continous duty  3,5A fuse Certification: CE marked ISO 9097:1991 Marine (small craft electrical fans), ISO8846 1990 (ignition protection), ISO 10133 2000 (electrical systems), EN55014-1 2006 (2004/108EC)