|
Tuthill 2LE-A-7 Pump 6.2Gpm 1/2"Ports
Cast Iron Rotary Gear Pump
Pump End Only
L Series Pump
Cast Iron Construction
Tang Shaft
Inlet Port is 1/2 inch NPT
Discharge Port is 1/2 inch NPT
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 5.6 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
715.00 |
|
|
Gianneschi EXCELSIOR-3 Bronze 1.25" Ports Hand Pump
|
2427.28 |
|
|
Tuthill 1LE-7 Pump 3.2Gpm 1/2"Ports Viton
Cast Iron Rotary Gear Pump
Pump End Only, NO motor
Cast Iron Construction
Inlet Port is 1/2 inch NPT, Discharge Port is 1/2 inch NPT
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 3.0 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
647.50 |
|
|
Tuthill 00LE-K-C Pump 1Gpm 1/2" Ports
|
625.81 |
|
|
Tuthill 00LE-K-C-7 Pump 1Gpm 1/2 Ports
Pump Body: Cast Iron
Shaft Seal: Mechanical Seal Viton
Port Size:Inlet Port is 1/2 inch NPT
Discharge Port is 1/2 inch NPT
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 1.0 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
626.88 |
|
|
Tuthill 00LE-C-7 Pump 1Gpm 1 1/2" Ports
Pump Body: Cast Iron
Shaft Seal: Mechanical Seal Viton
Port Size:Inlet Port is 1/2 inch NPT, Discharge Port is 1/2 inch NPT.
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 1.0 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
702.50 |
|
|
Tuthill 4C2B-C-7 Pump 36 Gpm 1 1/2Ports
Tuthill 4C2B-C-7, Cast Iron Rotary Gear Pump. Pump End Only. 36 GPM C Series. Cast Iron Construction NO motor. Flange mount. Clockwise rotation only (from shaft end view). Inlet Port is 1-1/2 inch NPT, Discharge Port is 1-1/2 inch NPT.
Features :
Pump Body:Cast Iron
Shaft Seal:Mechanical Seal Viton
Port Size:Inlet Port is 1-1/2 inch NPT
Discharge Port is 1-1/2 inch NPT.
|
1133.22 |
|
|
Tuthill 4C2EN-C-7 Pump 36Gpm 1 1/2 Ports With
Tuthill 4C2EN-C-7, Cast Iron Rotary Gear Pump. Pump End Only. 36 GPM C Series. Cast Iron Construction NO motor. Ball Bearing on Shaft. Clockwise rotation only (from shaft end view). Inlet Port is 1-1/2 inch NPT, Discharge Port is 1-1/2 inch NPT.
Features :
Pump Body:Cast Iron
Shaft Seal:Sleeve Bushing Lip Seal Viton
Port Size:Inlet Port is 1-1/2 inch NPT
Discharge Port is 1-1/2 inch NPT.
|
1319.88 |
|
|
Tuthill 0LE-C-7 Pump 1.8Gpm 1/2 Ports
Cast Iron Rotary Gear Pump
Pump End Only, NO motor
L Series
Cast Iron Construction
Has Internal Relief Valve Relief valve is set at 55 PSI (can be adjusted in field)
Clockwise rotation only (from shaft end view)
Inlet Port is 1/2 inch NPT, Discharge Port is 1/2 inch NPT
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 1.8 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
596.25 |
|
|
Flojet G57-3218 Pump Aod Viton 1/2" Ports
Flojet Diaphragm Pump AOD Air Powered, 1/2" Hose Barb Snap-In Ports, 5.5GPM Max, Polypropylene, Viton Check Valve Seat and Diaphragm, 1/4” Hose Barb Straight Plastic Air Inlet
Model No.: G57 Series
Capable of Air or CO2 drive pressures up to 100PSI (6.9bar)
Highest flow rate for any air pump of comparable size
Robust Design with durable integral mounting
Patented Shuttle Valve, eliminates stalling
Capable of passing solids up to 3.2mm diameter easily with large clog-free Check Valves
Corrosion Resistant materials capable of handling a wide range of chemicals
Sanitary design with insert molded diaphragm (Santroprene only)
Leak Resistant radial seals, no critical o-ring seals
Quiet Operation with large exhaust muffler
Ease of Installation with all quick disconnect ports
Stall-proof design with patented shuttle valve
Automotive Cleaning and Recycling; Chemical Transfer and dispensing; Bag-In-Box chemicals Parts Washers; Car Wash Systems
Innovative compact design features a patented shuttle valve that eliminates stalling and provides a long life. Features a chemically resistant polypropylene body with a choice of EP/PP blend, FKM or FFKM elastomers, as well as quick disconnect liquid and gas port fittings for easy installation.
|
315.84 |
|
|
March MDX-3 1/2" Ports Pump W/115V Mtr
|
281.78 |
|
|
Oberdorfer N992M-J07 Gear Pump 3/8" 1/2 Hp
|
1258.20 |
|
|
Applications for the MDX-3-1/2 Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.
March Pump's industrial MDX-3-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8 gallons per minute at 1 foot, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, carbon filled Kynar (PVDF), Ryton Buna N, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheitor 87 Celsius. The March MDX-3-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
8.5 GPM
30 LPM
Max Head
19 FT
4 M
Power
.04 HP
.029 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1/2"OD
Outlet
1/2"OD
Wet End
Polypropylene (Front Housing and Impeller), Carbon filled Kynar (Rear Housing, Shaft), Ryton (Thrust Washer), Buna N (O-Ring), Stainless Steel (Screw) Ceramic Magnet
|
328.58 |
|
|
March 1A-MD-1/2 Mag Drive Pump
March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI). The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel. When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 115V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.
Perfect for Applications Including
Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.
Great for Chemicals Including
The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.
Inlet: 1/2"OD
Outlet: 1/2"OD
Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft)
Uses:Submersible or Open Air
When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord
P/N:0115-0007-0200 (115V)
|
317.85 |
|
|
March 1A-MD-1/2 Mag Drive Pump
March Pump's industrial 1A-MD-1/2 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI). The 1A-MD-1/2 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, and Stainless Steel. When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 1/2 inch smooth, and the outlet is 1/2 inch smooth. The standard motor is a 1 Phase 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-1/2 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-1/2 is suitable for your application, please contact March Pump.
Perfect for Applications Including
Applications for the 1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.
Great for Chemicals Including
The 1A-MD-1/2 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.
Inlet: 1/2"OD
Outlet: 1/2"OD
Wet End: Polypropylene (Front Housing, Rear Housing, Impeller), Buna N (O-Ring), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft)
Uses:Submersible or Open Air
When submerged, the following is also in contact with the solutionEpoxy, Noryl, SJT Cord
P/N 0115-0007-0700 (230V)
|
320.78 |
|