Lynx Smart BMS 1000 Battery Management System for Lithium Smart Batteries The Lynx Smart BMS is a dedicated Battery Management System (BMS) for the Victron Lithium Battery Smart batteries. These batteries are Lithium Iron Phosphate (LiFePO4) batteries and are available in 12.8 V or 25.6 V in various capacities. They can be connected in series, parallel, and series/parallel so that a battery bank can be built for system voltages of 12V, 24 V, or 48 V. The maximum number of batteries in one system is 20, which results in a maximum energy storage of 84 kWh in a 12 V and up to 102 kWh in a 24 V1) and 48 V1) system. Out of the various available BMSes, the Lynx Smart BMS is the most feature-rich and complete option and integrates seamlessly into the Lynx Distributor system. This model is a 1000 A (M10) version. Built-in 1000 A Contactor The contactor acts as a secondary safety system to protect the battery in case the primary controls (ATC, ATD, and/or DVCC) fail to disable loads and/or chargers when required and is also suitable as a remote controllable main system switch. Pre-charge Circuit In addition to the contactor, a built-in pre-charge circuit prevents high inrush currents when connecting a capacitive load such as a MultiPlus/Quattro or other inverter, eliminating the need for external pre-charging. Monitoring and Control Monitor and control the BMS via Bluetooth using the VictronConnect App or a GX device such as a Cerbo GX and the VRM Portal. A built-in battery monitor that operates similarly as the other Victron Energy battery monitors, provides data such as state of charge, voltage, current, historical data, status info, and more in real-time and with instant readout even without the need to connect to the BMS, allowing diagnostic at a glance. DVCC closed Loop Control as Well as ATC/ATD Contacts Compatible Victron inverters/chargers and solar chargers are automatically controlled via a connected GX device and DVCC. The ATC/ATD contacts can be used to control other chargers and loads that have a remote on/off port. Programmable Relay The relay can be used either as an alarm relay (combined with the pre-alarm) or to control an alternator via its external regulator (ignition cable). In Alternator ATC mode, the relay will only activate when the contactor is closed. Alternator ATC contact of the alternator opens first and then with a delay of 2 seconds the contactor. These 2 seconds ensure that the alternator is switched off before the battery is disconnected from the system. AUX Terminal The advantage of the onboard auxiliary power supply (1.1 A @ system voltage) is to provide power to specific loads (i.e. a GX device) after the BMS has shut down the loads in the event of a low cell voltage event. If no charge voltage is detected within 5 minutes, the BMS, including the AUX connection switches off. VE.Can and NMEA 2000 Data Communication VE.Can allows for easy connection (standard RJ45 network cable) and communication with a GX device. Since the CANbus protocol is based on NMEA 2000 (and J1939), it is easy to integrate into a marine network and feed a marine MFD with data (requires a VE.Can to NMEA 2000 micro-C male cable). Lynx Distributor Fuse Monitoring Read out the fuse status and receive an alarm in case a fuse is blown. The Lynx Smart BMS monitors up to 4 connected Lynx Distributors and their fuses via VictronConnect or a GX device 1) To reduce the required balancing time, we recommend using as many different batteries in series as possible for the application. 24 V systems are best built using 24 V batteries, and a 48 V system. This System Contains the Following Components: Lynx Distributor with 2 fused paralleled lithium-ion smart batteries. Lynx Smart BMS with BMS, contactor, and battery monitor A second Lynx distributor provides fused connections for inverter/charger(s), loads and chargers (additional modules can be added if more connections are needed) A Cerbo GX (or other GX device) to read out the Lynx Smart BMS and Lynx Distributor data. Power Specifications: Battery Voltage Range: 9 – 60 VDC Maximum Input Voltage: 75 VDC Supported System Voltages: 12, 24, or 48 V Reverse Polarity Protection: No Main Safety Contactor Continuous Current Rating: 1000 A continuous Main Safety Contactor Peak Current Rating: 1200 A for 5 minutes  Power Consumption OFF Mode: 0.3 mA for all system voltages Power Consumption in Standby Mode: Approximately 0.6 W (50 mA at 12 V) Power Consumption in ON Mode: Approx. 2.6 W (217 mA at 12 V) depending on the state of the relays Approximately 4.2 W (350 mA at 12 V) depending on the state of the relays Minimum Load Resistance for Pre-Charging: 10 Ω and above for 12 V systems, 20 Ω and above for 24 V and 48 V systems AUX Output Maximum Current Rating: 1.1 A continuous, protected by resettable fuse Allow-to-Charge Port Maximum Current Rating: 0.5 A at 60 VDC, protected by a resettable fuse Allow-to-Discharge Port Maximum Current Rating: 0.5 A at 60VDC, protected by a resettable fuse Alarm Relay (SPDT) Maximum current Rating: 2 A at 60 VDC Connections: Busbar: M10 (Torque: 17 Nm) VE.Can: RJ45 I/O: Removable multi-connector with screw terminals Battery BTV Cables: Male and female circular 3-pole connector with M8 screw ring Up to 20 batteries can be connected in one system Lynx Distributor fuse monitoring (up to 4 modules) RJ10 (cable ships with each Lynx Distributor) Physical Specifications: Enclosure Material: ABS Enclosure Dimensions (h x w x d): 230 x 180 x 100 mm Unit Weight: 2.7 kg Busbar Material: Tinned copper Busbar Dimensions (h x w): 8 x 30 mm Environmental Specifications: Operating Temperature Range: -40 °C to +60 °C Storage Temperature Range: -40 °C to +60 °C Humidity Max.: 95 % (non-condensing) Protection Class: IP22 Standards Safety: EN-IEC 63000:2018 EMC: EN-IEC 61000-6-3:2007/A1:2011/AC:2012 QMS: NEN-EN-ISO 9001:2015 Please contact your dealer for any returns, repairs or support issues related to this product.

Lynx Smart BMS 500 Battery MGMT System for Lithium Smart Batteries The Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature-rich and complete option. Features: Built-in 500A contactor, used as a fall-back safety mechanism and also available as a remote controllable main systems switch Battery monitor, indicating the state of charge percentage and more data. Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell. Bluetooth for use with our VictronConnect App, for setup and monitoring. Local and remote monitoring using a Victron GX device, for example, the Cerbo GX. The Lynx Smart BMS is part of the modular Lynx distribution system. Please contact your dealer for any returns, repairs or support issues related to this product.

Lynx Distributor with M10 Terminals The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. This model is part of the Lynx distribution and is a M10 busbar model. Note that M10 refers to the busbar connection joints where the modules are connected. The fuse and cable connections are always M8. The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can. Features: 1000A model with M10 busbars The Lynx Distributor ships together with a 40cm RJ10 cable, which provides power to the Lynx Distributor and is also used to transmit data if connected to a Lynx Smart BMS The Lynx Distributor is designed to hold MEGA fuses If the Lynx Distributor is connected to a Lynx Smart BMS, it can be monitored and set up with the VictronConnect App Up to 4 connected Lynx distributors can be monitored with a GX device if connected to a Lynx Smart BMS The Lynx Distribution System The Lynx Distribution System is a modular busbar system that incorporates DC connections, distribution, fusing, and battery monitoring and/or lithium battery management. The Lynx Distribution System Consists of the Following Parts Lynx Power In A positive and negative busbar with four batteries or DC equipment connections. Lynx Distributor A positive and negative busbar with four fused connections for batteries or DC equipment and fuse monitoring, is available in two versions. Lynx Shunt VE.Can A positive busbar with a space for a main system fuse and a negative busbar with a shunt for battery monitoring. It has VE.Can communication for monitoring and setup with a GX device. Lynx Smart BMS For use together with Victron Energy Smart Lithium batteries. It contains a positive busbar with a contactor driven by a battery management system (BMS) and a negative busbar with a shunt for battery monitoring. It has Bluetooth communication for monitoring and setup via the VictronConnect App and VE.Can communication for monitoring with a GX device and the VRM portal. Available as a 1000A model with M10 busbars. Please contact your dealer for any returns, repairs or support issues related to this product.

Lynx Power-In Class-T M10 Terminals The Lynx Class-T Power In connects and fuses up to two strings of lithium batteries. It features a positive and negative busbar, connections for two Class-T fuses, and a connection to ground the DC system. The Class T-fuses, are available in 225A, 250A, 350A, and 400A (must be purchased separately). For installations using three or more strings of lithium batteries, use multiple Lynx Class-T modules. As a core component of the Lynx Distribution system, the Lynx Class-T seamlessly integrates with all other M10 Lynx products. The Lynx Distribution System The Lynx Distribution System is a modular busbar system that incorporates DC connections, distribution, fusing, and battery monitoring and/or lithium battery management.  The Lynx Distribution System Consists of the Following Parts Lynx Power In A positive and negative busbar with four batteries or DC equipment connections. Lynx Distributor A positive and negative busbar with four fused connections for batteries or DC equipment and fuse monitoring is available in two versions. Lynx Shunt VE.Can A positive busbar with a space for a main system fuse and a negative busbar with a shunt for battery monitoring. It has VE.Can communication for monitoring and setup with a GX device. Lynx Smart BMS For use together with Victron Energy Smart Lithium batteries. It contains a positive busbar with a contactor driven by a battery management system (BMS) and a negative busbar with a shunt for battery monitoring. It has Bluetooth communication for monitoring and setup via the VictronConnect App and VE.Can communication for monitoring with a GX device and the VRM portal. Available as a 1000A model with M10 busbars. Specifications Power: Voltage Range: 9 - 60Vdc Current Rating: 1000Adc continuous  Connections: M10 Busbar: 3/8” Physical: Enclosure Material: ABS Enclosure Dimensions (H x W x D): 279 x 169 x 97mm Unit Weight: 2.1 kg Busbar Material: Tinned copper Busbar Dimensions (H x W): 8 x 30mm Environmental: Operating Temperature Range: -40°C to +60° Storage Temperature Range: -40°C to +60° Humidity: Max. 95% (non-condensing) Protection Class: IP20 Please contact your dealer for any returns, repairs or support issues related to this product.

Lynx Power-In with M10 Terminals The Lynx Power In contains a positive and negative busbar with 4 connections for batteries, loads, or chargers and a ground connection. It is part of the Lynx Distribution System. This version is a M10 busbar. Note that M10 refers to the busbar connection joints where the modules are connected. The fuse and cable connections are always M8. The Lynx Distribution System The Lynx Distribution System is a modular busbar system that incorporates DC connections, distribution, fusing, and battery monitoring and/or lithium battery management.  The Lynx Distribution System Consists of the Following Parts Lynx Power In A positive and negative busbar with four batteries or DC equipment connections. Lynx Distributor A positive and negative busbar with four fused connections for batteries or DC equipment and fuse monitoring, is available in two versions. Lynx Shunt VE.Can A positive busbar with a space for a main system fuse and a negative busbar with a shunt for battery monitoring. It has VE.Can communication for monitoring and setup with a GX device. Lynx Smart BMS For use together with Victron Energy Smart Lithium batteries. It contains a positive busbar with a contactor driven by a battery management system (BMS) and a negative busbar with a shunt for battery monitoring. It has Bluetooth communication for monitoring and setup via the VictronConnect App and VE.Can communication for monitoring with a GX device and the VRM portal. Available as a 1000A model with M10 busbars. Please contact your dealer for any returns, repairs or support issues related to this product.

12V - 12 AH Max Lithium Battery Vexilar’s MAX Lithium Battery delivers 12 volts and 12 amps of power, the most in its class to be a drop-in replacement for existing 12-volt SLA batteries with half the weight. This battery is designed for the outdoor enthusiast on the go, with high capacity, a fast recharge time, rugged construction, and design features that make it ideal for portable summer and winter use. Great for fly-in trips too. FH1000 Fuse Holder Mounted on the positive terminal of your battery are a fuse holder and fuse. Vexilar knows your battery can cause fires if a dead short happens, so we have taken the added safety precaution to include this fuse holder with a 3 amp fuse for your battery. It comes standard with a 3 amp automotive fuse, but you can put in a size fuse from 3 amp to 10 amps. If your sonar system does not power up, check to see if the fuse or fuse holder is loose. If your sonar system does not power up, inspect the fuse itself, if the wire inside the fuse is burnt, the fuse must be replaced Yes, your Vexilar can run without the fuse holder by connecting directly to the battery, but please use it whenever possible for safety purposes. If for some reason you’ve lost your fuse holder or would like to put them on all your Vexilar systems, they are available directly at vexilar.com, part number: FH1000 Lightweight and powerful, the V-200L 12 Volt, 12 amp-hour Vexilar MAX Lithium battery has been designed to replace any current Vexilar Flasher/Pack battery and may still allow the use of the 1 amp, fully-automatic Vexilar battery charger or the recommended new V-420L rapid charger. Features: Drop-in replacement for any current Vexilar Flasher/Pack battery LiFePO4 technology Delivers twice the number of battery re-charging cycles over sealed lead-acid batteries Half the weight of the sealed lead-acid battery

Remote Battery Management Cluster f/Single Engine Offers all features of motorized battery switches and Motorized VSRs in one kit. Makes ordering easy! Clusters are surface mount, and can be rearranged to meet specific needs, such as port and starboard configurations and can be combined with other battery distribution products. Available in single, dual and triple engine configurations WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Remote Battery Management Cluster f/Twin Engine Offers all features of motorized battery switches and Motorized VSRs in one kit. Makes ordering easy! Clusters are surface mount, and can be rearranged to meet specific needs, such as port and starboard configurations and can be combined with other battery distribution products. Available in single, dual and triple engine configurations. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Remote Battery Management Cluster f/Triple Engine Offers all features of motorized battery switches and Motorized VSRs in one kit. Makes ordering easy! Clusters are surface mount, and can be rearranged to meet specific needs, such as port and starboard configurations and can be combined with other battery distribution products. Available in single, dual and triple engine configurations WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

15Ah Lithium Battery Kit Replacement 15AH lithium battery for portable and ICE fishing systems. Features: Dual USB Ports: Keep your electronics charged and power accessories while out on the ICE. LED Battery Level Indicator: Always know how much charge is in your battery. 1-Year Limited Warranty

20Ah Lithium Battery Kit Replacement 20AH lithium battery for portable and ICE fishing systems. Features: Dual USB Ports: Keep your electronics charged and power accessories while out on the ICE. LED Battery Level Indicator: Always know how much charge is in your battery. 1-Year Limited Warranty

Lithium Battery 12VDC - 100AH - Smart LifePO4 Features: With integrated cell balancing Can be parallel and series connected  Bluetooth app available to monitor cell voltage and temperature Requires one of these BMS-es: VE.Bus BMS – recommended for systems with our inverter/chargers. smallBMS – recommended for use in small systems.  Battery Management System BMS 12/200 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Smart BMS 12/200 - recommended for use in Automotive and Marine systems having DC-loads and Alternators.  Smart BMS CL 12/100 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Lynx Smart BMS - recommended for use in large systems. Please contact your dealer for any returns, repairs or support issues related to this product.

Lithium Battery 24VDC - 100AH - Smart LifePO4 Features: With integrated cell balancing Can be parallel and series connected  Bluetooth app available to monitor cell voltage and temperature Requires one of these BMS-es: VE.Bus BMS – recommended for systems with our inverter/chargers. smallBMS – recommended for use in small systems.  Battery Management System BMS 12/200 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Smart BMS 12/200 - recommended for use in Automotive and Marine systems having DC-loads and Alternators.  Smart BMS CL 12/100 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Lynx Smart BMS - recommended for use in large systems. Please contact your dealer for any returns, repairs or support issues related to this product.

Lithium Battery 24VDC - 200AH - Smart LifePO4 Features: With integrated cell balancing Can be parallel and series connected  Bluetooth app available to monitor cell voltage and temperature Requires one of these BMS-es: VE.Bus BMS – recommended for systems with our inverter/chargers. smallBMS – recommended for use in small systems.  Battery Management System BMS 12/200 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Smart BMS 12/200 - recommended for use in Automotive and Marine systems having DC-loads and Alternators.  Smart BMS CL 12/100 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Lynx Smart BMS - recommended for use in large systems. Please contact your dealer for any returns, repairs or support issues related to this product.

VE.Bus BMS V2 for Victron LiFePO4 Batteries 12-48VDC - Work with All VE.Bus & GX Devices The VE.Bus BMS and VE.Bus BMS V2 is Battery Management System (BMS) designed to interface with and protect a single or multiple Victron Lithium Battery 12,8V & 25,6V Smart (LiFePO4 or LFP) in systems that have Victron inverters or inverter/chargers with VE.Bus communication. It monitors and protects the batteries against the over voltage and under voltage of any individual cell, and also over temperature or under temperature conditions. Based on the status of the battery or batteries, the BMS will: Generate a pre-alarm signal to alert of an imminent cell under voltage conditions. Disable inverting in VE.Bus inverters or inverters/chargers via VE.Bus, and disable other loads via the 'Load Disconnect' terminal in the event of a cell under voltage conditions. Disable charging in VE.Bus inverters or inverters/chargers via VE.Bus and disable other chargers via the 'Charge Disconnect' terminal in the event of a cell overvoltage, under-temperature, or over-temperature conditions. The "original" VE.Bus BMS is best used in systems without a GX device The "next generation" VE.Bus BMS V2 has additional features such as: Remote on/off terminals. Ability to disable VE.Direct and VE.Can solar chargers via a GX device. Allowing control of the VE.Bus inverter/charger from multiple devices, like the Digital Multi Control, the VE.Bus Smart dongle and/or a GX device. Auxiliary power input and output terminals that allow a GX device to remain powered in the event of a system shutdown. Please contact your dealer for any returns, repairs or support issues related to this product.