109 Backing Plate with Gasket - Anodized Aluminum Use with the Smooth Slide Rocket Launcher.

Sidewinder Backing Plate f/Bolt-In Holders Below top operation. Fully locked in Running and 80° out Trolling positions. Locks when handle is up or down. Rotates when handle is to the left or right. Fastest Lay-Down on the market. Automatically locks in position when raising or lowering the pole. No knobs to loosen or tighten. Just pull down the Ridged Collar and lower or raise the pole. Available with Quick Laydown or Curved Tube. No ball bearings to rust. Internal Delrin and nylon bearing surfaces provide smooth operation and prevent metal to metal contact. Accepts our 16Ft Extra Strong (AP3916XS) or 18Ft (AP3918) Outrigger Pole. Has 4"x6" Mounting plate. Extends 14" above and 8-1/2" below mounting plate. Fits all outrigger ready boats.

Top Gun Backing Plate Secure your new Top Guns with custom-designed backing plates made of anodized aircraft aluminum. These backing plates work with any bolt-in Top Gun or Z-30 outrigger bases. Needed when top thickness is not sufficient to support outrigger bases. Sold individually - 2 required.

Backing Plates For Grand Slam Outriggers (pair) Part #: BP-150BSY-320-1 Specifically made for additional support for Grand Slam Outriggers when mounting to hard tops and gunnels. Made of Anodized Aluminum.

Grand Slam GS-950BHC Electric Anchor & Stern Light - Black Anodized Aluminum Not only can boaters adjust the position of their masthead anchor light with the simple push of a button, but the popular GS-950 is now available with a black hard coat anodized aluminum finish – providing enhanced protection from the elements in style. Ideal for powered vessels 39’ and under (12 meters and under), the GS-950BHC is certified for USCG-required 3 nautical miles. The GS-950BHC is a fully electric unit with hidden wires inside the hardtop. This mount easily installs to the surface of the hardtop and fits all top thicknesses. The GS-950BHC lights run on 12 volts and consist of four 3-watt LED Cree chips driven by two Mean Well drivers. Features & Benefits: 4 Electric Masthead Anchor Lights Black hard coat anodized aluminum Machined / Anodized aluminum body with a Light-brushed finish  Certified for USCG-required 3-nm  Includes tube, light, and 6” lead of 20-gauge wire from the base 12-volt DC power supply for light function  Threaded shaft for consistent lift and descent  Brass bearings for smooth operation  Features breakaway pin for manual operation Mounts to all hardtops  Reliable long-life LEDs  6-Watt Stern Light and 12-watt Anchor  Low-draw, 0.6 amps per light  Low-voltage 12-24VDC  Pairs with Backing Plate (BP-0850AEY), which is sold separately Pairs with 6-degree Wedge Plate (WP-850-950), which is sold separately Made in the USA  1-year limited warranty Specifications: Mount Base Diameter (inch): 4-1/4" Max height of Mount (inch): 6-1/8" Individual Weight (pounds): 3.5 lbs. *Sold in a case of four  

ShadeFin Mini Semi-Flush Mount with Backing Plate The ShadeFin Mini Semi-Flush Mount is ideal for boat decks, console tops, or any flat surface. The unique design of the semi-flush mount enables the post to be removed and stowed when not in use, leaving only a semi-flush ring secured in place. To use the Semi-Flush Mount, simply install the threaded locking ring and the post to the semi-flush ring, tighten securely, and mount the ShadeFin Mini. Features and Benefits: Constructed out of aluminum-grade 6061 alloys with stainless steel Type-304 screws Includes an injection-molded nylon cap Includes a backing plate and mounting hardware 3-year limited warranty Specifications: Finish: Anodized aluminum finish    

Dashboard Mount with Backing Plate for 7"-8" Tablets with Cases The RAM® Tab-Tite™ bundle is a rugged mount including the RAM® Tab-Tite™, RAM® Universal Double Ball Mount with Two Round Plates, and RAM® Backing Plate Adapter. The RAM® Tab-Tite™ spring-loaded, quick-release holder offers a secure fit with easy access to the mounted tablet. The spring-loaded design makes it easy to insert and remove your tablet, along with keeping it secure in mobile applications. The custom end cups are designed to optimize the functionality of your tablet, enabling access to all ports and tablet functions. The RAM-101U-B consists of a short double socket arm and two 2.5" diameter round bases with the universal AMPS hole pattern. Designed into the mount is a 1.5" diameter patented rubber ball and socket system with adjustment points at both socket ends of the arm. Rubber ball and socket technology allow for almost infinite adjustment and perfect viewing angles. The included 2.10" x 2.60" steel backing plate with #8-32 threaded holes attaches to a variety of RAM® Mounts ball bases. Features: The spring-loaded holder secures 7 in. -8 in. tablets with a case; interchangeable end cups allow you to modify the holder when upgrading devices Drill-down mounting solution; choose either round plate featuring the AMPS hole pattern for attachment to compatible device holders 2.10 in. x 2.60 in. steel backing plate attaches to a variety of RAM® Mounts ball bases Ball and socket technology allows for near-infinite adjustability Backed by a lifetime warranty Specifications: Hardware Included: Assembly Hardware, (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Holder Dimensions (inch): Height Range: 8.32" - 10.92", Width Range: 4.43" - 5.3", Depth Range: .13" - .62" Socket to Socket Length (inch): 2.5” Hole Pattern (inch): 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Ball Size (inch): C size (1.5”) Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs. Materials: Marine-grade aluminum, high-strength composite, powder-coated steel Weight: 1.98 lb. Compatible Devices: Samsung: Galaxy Tab 4 8.0 with Otterbox Defender Case, Galaxy Tab A 8.0 (2017) with Case, Galaxy Tab A 8.0 (2018) with Case, Galaxy Tab A 8.0 (2019) with Case, Galaxy Tab S 8.4 with Otterbox Defender Case, Galaxy Tab E 8.0 with Verizon Rugged Case, and Galaxy Tab Active2

DA Backing Plate - 5" Meguiar's DA backing plates are designed to distribute pressure evenly for smoother sanding and finishing. The outer edges are precisely tuned for disc contouring over flat and curved surfaces. These backing plates also features a rotation indicator marking that allows the user to recognize backing plate rotation for ideal results. Can be attached to all DA polishers with a 5/16" diameter shaft. Features: Distributes pressure for smoother sanding and finishing Precisely tuned outer edges for ideal pad & disc contouring over fl at and curved surfaces Quick and easy pad & disc changes with micro hook and loop attachment system Fits all DA Polishers with 5/16" diameter shaft

Double Ball Mount with Backing Plate This mount consists of a double socket arm, two 2.5" diameter round bases that contain the universal AMPS hole pattern, a 2.10" x 2.60" backing plate, and mounting hardware. The mount is designed with a 1" diameter rubber ball and socket system that features adjustment points at both ends of the double socket arm, allowing for near-infinite adjustability for ideal viewing angles. Features: 2.10 in. x 2.60 in. steel backing plate attaches to a variety of RAM® Mounts ball bases 2.5 in. round plate with a B-size 1 in. RAM® rubber ball connects to RAM® device holders containing the universal AMPS hole pattern; includes a B-size medium-length double socket arm Made of stainless steel and high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Product Dimensions (inch): Overall Height: 5" Socket to Socket Length (inch): 3” Hole Pattern (inch): 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Plate Size (inch): 2.5" Diameter, 3" x 3" Square Plate Ball Size (inch): B size (1”) Weight Capacity: The standard use is 2 lbs. and the heavy-duty use is 1 lb. Materials: Marine-grade aluminum and stainless steel Weight: 0.79 lb.

Dashboard Mount with Backing Plate for 8" Tablets with Cases This vehicle kit consists of a RAM® Tab-Tite™ spring-loaded holder for 8" tablets with a case, a medium B-size double socket arm, two 2.5" diameter round bases that contain the universal AMPS hole pattern, a 2.10" x 2.60" backing plate, and mounting hardware. The mount is designed with a 1-diameter B-size rubber ball and socket system that features adjustment points at both ends of the double socket arm, allowing for near-infinite adjustability for ideal viewing angles. Features: The spring-loaded holder secures most 8 in. tablets with a case; interchangeable end cups allow you to modify the holder when upgrading devices Includes a 4-hole AMPS pattern ball adapter, a B-size medium-length double socket arm, and a backing plate kit for drill-down mounting; ball and socket technology allows for near-infinite adjustability Made of powder-coated, marine-grade aluminum and high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: Assembly Hardware, (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Holder Dimensions (inch): Height Range: 7.125" - 9.5", Width Range: 5.06" - 5.68", Depth Range: .13" - 1" Socket to Socket Length (inch): 3” Hole Pattern (inch): 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Plate Size (inch): 2.5" Diameter Ball Size (inch): B size (1”) Weight Capacity: The standard use is 2 lbs. and the heavy-duty use is 1 lb. Materials: Marine-grade aluminum, high-strength composite, and powder-coated steel Weight: 1.04 lb. Compatible Devices: Apple: iPad mini 6 with Case Amazon: Fire 7 Kids, Fire HD 8 Kids, and Fire HD 8 with Case ASUS: MeMO Pad 8 with Case, VivoTab 8 with Case Dell: Venue 8 with Case, Venue 8 (2014) with Case, Venue 8 7840 with Case, and Venue 8 Pro with Case Huawei: MediaPad M3 with Case, MediaPad M3 Lite with Case, MediaPad T1 8.0 with Case, and MediaPad T3 8 with Case Lenovo: Ideapad Miix 300 with Case, IdeaTab A2107 with Case, Tab 2 A8 with Case, Tab 4 8 with Case, Tab 4 8 Plus with Case, Tab A8-50 with Case, Tab S8 with Case, and Tab3 8 with Case LG: G Pad F 8.0 (2nd Gen) with Case, G Pad F2 8.0 with Case, G Pad II 8.0 with Case, and G Pad X II 8.0 with Case Nvidia: Shield Tablet with Case Panasonic: Toughpad FZ-M1 Samsung: Galaxy Tab 2 7.0 with Case, Galaxy Tab 3 8.0 with Case, Galaxy Tab A 8.4 with Case, Galaxy Tab A7 Lite 8.7 with Case, Galaxy Tab E 8.0 with Case, Galaxy Tab Pro 8.4 with Case

Dashboard Mount with Backing Plate for 9"-10.5" Tablets with Cases This rugged dashboard tablet mount consists of a RAM® Tab-Tite™ spring loaded holder for any 9 in. -10.5 in. tablets with a case, a medium C-size double socket arm, two 2.5 in. diameter round bases that contain the universal AMPS hole pattern, a 2.10" x 2.60" backing plate, and mounting hardware. The mount is designed with a 1.5" diameter C-size rubber ball and socket system that features adjustment points at both ends of the double socket arm, allowing for near-infinite adjustability for ideal viewing angles. Features: A spring-loaded holder secures most 9-10.5 in. tablets with cases; interchangeable end cups allow you to modify the holder when upgrading devices Includes 4-hole AMPS pattern ball adapter, a C-size medium-length double socket arm, and a backing plate kit for drill-down mounting; ball and socket technology allows for near-infinite adjustability Made of powder-coated, marine-grade aluminum and high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: Assembly Hardware, (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, (4) #8 Flat Washers Holder Dimensions (inch): Height Range: 9.5" - 12.125", Width Range: 6.55" - 7.43", Depth Range: .3" - .875" Socket to Socket Length (inch): 2.5” Hole Pattern (inch): 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Ball Size (inch): C size (1.5”) Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs. Materials: Marine-grade aluminum, high-strength composite, powder-coated steel Weight: 1.9 lb. Compatible Devices: Apple: iPad (5th Generation) with Case, iPad (6th Generation) with Case, iPad (7th Generation) with Case, iPad (8th Generation) with Case, iPad (9th Generation) with Case, iPad (10th Generation) with Case, iPad 9.7 (2017) with Case, iPad 9.7 (2018) with Case, iPad Air with Case, iPad Air 2 with Case, and iPad Pro 10.5 (2nd Generation) with Case ASUS: ZenPad 10 with Case, ZenPad 3S 10 with Case, and ZenPad Z10 with Case Dell: Venue 10 7000, Venue 11 Pro, and Venue 11 Pro 7000 Huawei: MediaPad M2 10.0 with Case Lenovo: Tab 2 A10-70 with Case, Tab 4 10 with Case, Tab 4 10 Plus with Case, Tab3 10 Business with Case, and Yoga Tab 3 10 with Case LG: G Pad 10.1 with Case, G Pad II 10.1 with Case, G Pad X 10.1 with Case, and G Pad X II 10.1 with Case Microsoft: Surface Go with Case and Surface Go 2 with Case Samsung: Galaxy Tab 10.1 with Case, Galaxy Tab 3 10.1 with Case, Galaxy Tab 8.9 with Case, Galaxy Tab A 9.7 with Case, Galaxy Tab A 10.5 with Case, Galaxy Tab Pro 10.1 with Case, Galaxy Tab S2 9.7 with Case, Galaxy Tab S3 9.7 with Case, Galaxy Tab S4 10.5 with Case, Galaxy Tab S6 with Case, Galaxy Tab S7 with Case, and Galaxy Tab S8 with Case Sony: Xperia Tablet Z with Case Vankyo: MatrixPad Z4 10"

Drill-Down Dashboard Mount with Backing Plate - C Size Medium Meet the new go-to mount and component option for pairing any holder or dock with a dashboard drill-down mount. The RAM-101-225B2U consists of a C-size medium-length double socket arm, two round 2.5" diameter round bases with the universal AMPS hole pattern, and one 2.10" x 2.60" steel backing plate (hardware included). RAM®'s patented rubber ball and socket technology dampens shock and vibration and allows for near-infinite adjustment, enabling the perfect viewing and operating angle of your device. Features: Drill-down double ball mount with a 2.10 x 2.60 in. steel backing plate that connects to RAM® components containing the universal AMPS hole pattern Includes a C-size 1.5 in. RAM® rubber ball and a medium-length double socket arm; ball and socket technology allows for near-infinite adjustability Components made of powder-coated, marine-grade aluminum, and steel for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Machine Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Product Dimensions (inch): Overall Height: 7.35" Socket to Socket Length (inch): 4.66” Hole Pattern: Round Plate:, 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Ball Size (inch): C size (1.5”) Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs. Materials: Marine-grade aluminum and steel Weight: 1.4 lb.

Drill-Down Dashboard Mount with Backing Plate - C Size Short Meet the new go-to mount and component option for pairing any holder or dock with a dashboard drill-down mount. This mount consists of a C-size short-length double socket arm, two round 2.5" diameter round bases with the universal AMPS hole pattern, and one 2.10 x 2.60 in. steel backing plate (hardware included). RAM®'s patented rubber ball and socket technology dampens shock and vibration and allows for near-infinite adjustment, enabling the perfect viewing and operating angle of your device. Features: Drill-down double ball mount with a 2.10 x 2.60 in. steel backing plate that connects to RAM® components containing the universal AMPS hole pattern Includes a C-size 1.5" RAM® rubber ball and a short double socket arm; ball and socket technology allows for near-infinite adjustability Components made of powder-coated, marine-grade aluminum, and steel for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Machine Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Product Dimensions (inch): Overall Height: 5.225" Socket to Socket Length (inch): 2.5” Hole Pattern: Round Plate:, 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Ball Size (inch): C size (1.5”) Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs. Materials: Marine-grade aluminum and steel Weight: 1.16 lb.

Drill-Down Dashboard Ball Base with Backing Plate - B Size Meet the new go-to mount and component option for pairing any holder or dock with a dashboard drill-down mount. This part consists of a 1" B-size rubber ball connected to a 2.5" diameter round plate with the universal AMPS hole pattern and one 2.10 x 2.60 in. steel backing plate (hardware included).  Connect a B-size RAM® double socket arm and device holder that's perfect for the use case. RAM®'s patented rubber ball and socket technology dampens shock and vibration and allows for near-infinite adjustment, enabling the perfect viewing and operating angle of your device. Features: 2.5 in. round plate with a B-size 1 in. rubber ball connects to the included 2.10 x 2.60 in. steel backing plate that connects to RAM® components containing the universal AMPS hole pattern Connect a B-size RAM® double socket arm and device holder for your use case; ball and socket technology allows for near-infinite adjustability Components made of powder-coated, marine-grade aluminum, and steel for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Machine Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Product Dimensions (inch): Overall Height: 5.225" Socket to Socket Length (inch): 2.5” Hole Pattern: Round Plate:, 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Ball Size (inch): B size (1”) Weight Capacity: The standard use is 2 lbs. and the heavy-duty use is 1 lb. Materials: Marine-grade aluminum and steel Weight: 0.42 lb.

Drill-Down Dashboard Ball Base with Backing Plate - C Size Meet the new go-to mount and component option for pairing any holder or dock with a dashboard drill-down mount. This part consists of a 1.5 in. C-size rubber ball connected to a 2.5 in. diameter round plate with the universal AMPS hole pattern and one 2.10 x 2.60 in. steel backing plate (hardware included). Connect a C-size RAM® double socket arm and device holder that's perfect for your use case. RAM®'s patented rubber ball and socket technology dampens shock and vibration and allows for near-infinite adjustment, enabling the perfect viewing and operating angle of your device. Features: 2.5 in. round plate with a C-size 1.5 in. rubber ball connects to the included 2.10 x 2.60 in. steel backing plate that connects to RAM® components containing the universal AMPS hole pattern Connect a C-size RAM® double socket arm and device holder for your use case; ball and socket technology allows for near-infinite adjustability Components made of powder-coated, marine-grade aluminum, and steel for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Machine Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Hole Pattern: Round Plate: 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Ball Size (inch): C size (1.5”) Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs. Materials: Marine-grade aluminum and steel Weight: 0.5 lb.